﻿<?xml version="1.0" encoding="utf-8" standalone="no"?><Search><pages Count="142"><page Index="1" isMAC="true"><![CDATA[XLT1200OWNER’S/OPERATOR’S MANUALU.S.A. EditionREAD THIS MANUALCAREFULLY BEFORE OPERATION!LIT-18626-04-382002 WaveRunner]]></page><page Index="2" isMAC="true"><![CDATA[]]></page><page Index="3" isMAC="true"><![CDATA[Thank you for choosing a Yamaha water- craft.This Owner’s/Operator’s Manual contains information you will need for proper opera- tion, maintenance, and care. A thorough understanding of these simple instructions will help you to obtain maximum enjoyment from your new Yamaha. If you have any questions about the operation or mainte- nance of your watercraft, please consult a Yamaha dealer.Because Yamaha has a policy of continu- ing product improvement, this product may not be exactly as described in this Owner’s/ Operator’s Manual. Specifications are sub- ject to change without notice.This manual should be considered a per- manent part of this watercraft and should remain with it even if the watercraft is subse- quently sold.EJU01204Important manual information:In this manual, information of particular importance is distinguished in the following ways:The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!@Failure to follow WARNING instructions could result in severe injury or death to the machine operator, passengers, a bystander, or a person inspecting or repairing the watercraft.@@A CAUTION indicates special precau-tions that must be taken to avoid damageto the watercraft.@A NOTE provides key information to makeprocedures easier or clearer.@To the owner/operatorEEJU00989WARNINGCAUTION:NOTE: @EJU01173WaveRunner XLT1200 OWNER’S/OPERATOR’S MANUAL ©2001 by Yamaha Motor Corporation, USA 1st Edition, July 2001All rights reserved.Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, USAis expressly prohibited.Printed in USAP/N LIT-18626-04-38]]></page><page Index="4" isMAC="true"><![CDATA[]]></page><page Index="5" isMAC="true"><![CDATA[EJU00992ECONTENTSGENERAL AND SAFETY INFORMATION123456FEATURES AND FUNCTIONSOPERATIONMAINTENANCE AND CARETROUBLESHOOTING AND EMERGENCY PROCEDURESAPPENDIXREAD THIS OWNER’S/OPERATOR’S MANUAL CAREFULLY BEFORE OPERATING YOUR WATERCRAFT.]]></page><page Index="6" isMAC="true"><![CDATA[]]></page><page Index="7" isMAC="true"><![CDATA[EJU00993GENERAL AND SAFETY 1INFORMATIONIdentification numbers ............................1-1 Primary Identification (PRI-ID)number ...................................................1-1 Hull Identification Number (HIN) ............1-1 Engine serial number .............................1-1Emission control information ................1-2 Approval label of Emission control certificate ................................................1-2 Manufactured date label ........................1-2Important labels .......................................1-3 Label location .........................................1-3 Warning labels .......................................1-4 Caution labels ........................................1-6 Other labels ............................................1-7Safety information .............................1-8 Limitations on who may operate the watercraft ................................................1-8 Cruising limitations .................................1-9 Operation requirements .......................1-10 Recommended equipment ..................1-12 Hazard information ..............................1-13 Watercraft characteristics ....................1-13 Water-skiing .........................................1-14Rules of the Road ..................................1-16 Steering and sailing rules ....................1-16 Rules when encountering vessels ......1-17 Other special situations .......................1-18 Reading buoys and other markers ......1-18To get more boating safetyinformation .............................................1-20United States Coast Guard .................1-20 Other sources ......................................1-20 Watercraft Education and Training ......1-20Enjoy your watercraft responsibly ......1-21E]]></page><page Index="8" isMAC="true"><![CDATA[E1-1EJU00994Identification numbersRecord your Primary Identification (PRI- ID) number, Hull Identification Number (HIN) and engine serial number in the spaces pro- vided, to assist you in ordering spare parts from a Yamaha dealer. Also record and keep these ID numbers in a separate place in case your watercraft is stolen.EJU00995Primary Identification (PRI-ID) numberThe PRI-ID number is stamped on a label 1 attached to the inside of the engine compart- ment.EJU01205Hull Identification Number (HIN)The HIN is stamped on a plate 2 attached to the aft deck.EJU00997Engine serial numberThe engine serial number is stamped on a label 3 attached to the engine unit.]]></page><page Index="9" isMAC="true"><![CDATA[EEJU01174Emission control information1-2This engine conforms to the U.S. Environ- mental Protection Agency (EPA) regulations for marine SI engines for the year 2002.EJU01451Approval label of Emission control certificateThis label is attached to the electrical box and the intake side of the crankcase.1 Emission control information labelEJU01390Manufactured date labelThis label is attached to the electrical box and the intake side of the crankcase.2 Manufactured date label]]></page><page Index="10" isMAC="true"><![CDATA[EEJU00998EJU01351Label locationImportant labels1-3]]></page><page Index="11" isMAC="true"><![CDATA[EEJU01352Warning labels123451-4]]></page><page Index="12" isMAC="true"><![CDATA[67890AB1-5E]]></page><page Index="13" isMAC="true"><![CDATA[EEJU01353Caution labelsCDEFGHI1-6]]></page><page Index="14" isMAC="true"><![CDATA[EEJU01354Other labelsJKLM1-7]]></page><page Index="15" isMAC="true"><![CDATA[Safety informationEEJU01177EJU01159Limitations on who may operate the watercraftq Yamaha recommends a minimum opera-tor age of 16 years old.Adults must supervise use by minors. Know the operator age and training requirements for your state. A boating safety course is recommended and may be required in your state. You can find local rules by contacting the United States Coast Guard (USCG), the National Association of State Boating Law Admin- istrators, or your local Power Squadron.q This watercraft is designed to carry the operator and up to 2 passengers. Never exceed the maximum load limit or allow more than 3 persons (or 2 persons if a water-skier is being pulled) to ride the watercraft at one time.q Do not operate the watercraft with any passengers on board until you have con- siderable practice and experience riding alone. Operating the watercraft with pas- sengers requires more skill. Take the time to become accustomed to the handling characteristics of the watercraft before trying any difficult maneuvers.The safe use and operation of this watercraft is dependent upon the use of proper riding techniques, as well as upon the common sense, good judgment, and expertise of the operator. Every operator should know the following requirements before riding the watercraft.q Before operating the watercraft, read the Owner’s/Operator’s Manual, the Riding Practice Guide, the Riding Instruction card and all warning and caution labels on the watercraft. Also, watch the Basic Orientation Video provided with your watercraft. These materials should give you an understanding of the watercraft and its operation.q Never allow anyone to operate this water- craft until they too have read the Owner’s/ Operator’s Manual, the Riding Practice Guide, the Riding Instruction card and all warning and caution labels, and if possi- ble watched the Basic Orientation Video. Showing them the video may help rein- force the information contained in these materials.1-8Maximum load: 240 kg (530 lb)Load is the total weight of cargo, opera- tor and passengers.]]></page><page Index="16" isMAC="true"><![CDATA[EJU01001Cruising limitationsq Scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others.q Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft.q Do not follow directly behind watercraft or other boats.q Do not go near others to spray or splash them with water.q Avoid sharp turns or other maneuvers that make it hard for others to avoid you or understand where you are going.q Avoid areas with submerged objects or shallow water.q Ride within your limits and avoid aggres- sive maneuvers to reduce the risk of loss of control, ejection, and collision.q This is a high performance boat—not a toy. Sharp turns or jumping wakes or waves can increase the risk of back/spinal injury (paralysis), facial injuries, and bro- ken legs, ankles and other bones. Do not jump wakes or waves.q Do not operate the watercraft in rough water, bad weather or when visibility is poor; this may lead to an accident caus- ing injury or death. Be alert to the possi- bility of adverse weather. Take note of weather forecasts and the prevailing weather conditions before setting out on your watercraft.q As with any water sport, you should not ride your watercraft without someone else near by. If you ride further than swimming distance from shore, you should ride by another boat or watercraft, but make sure you stay a safe distance away. It’s good common sense!q Never operate in water that is less than 60 cm (2 ft) deep, otherwise you increase your chance of hitting a submerged object, which could result in injury.E1-9]]></page><page Index="17" isMAC="true"><![CDATA[Eq This watercraft is not equipped with light- ing required for night operation. Do not operate the watercraft after sunset or before dawn, otherwise you increase the risk of colliding with another boat, which could result in severe injury or death.EJU01160Operation requirementsq All riders must wear a Coast Guard approved personal flotation device (PFD) that is suitable for personal watercraft use.q Wear protective clothing. Severe internal injuries can occur if water is forced into body cavities as a result of falling into water or being near the jet thrust nozzle. Normal swimwear does not adequately protect against forceful water entry into rectum or vagina. All riders must wear a wetsuit bottom or clothing that provides equivalent protection. Such clothing includes thick, tightly woven, sturdy and snug-fitting apparel such as denim, but does not include spandex or similar fab- rics, like those used in bicycle shorts.1 Coast Guard approved PFD2 Wetsuit bottomq Eye protection is recommended to keepwind, water, and glare from the sun out of your eyes while you operate your water- craft. Restraining straps for eyewear are made which are designed to float should your eyewear fall in the water.Footwear and gloves are recommended.1-10]]></page><page Index="18" isMAC="true"><![CDATA[q Helmets meeting Snell or DOT standards are required for IJSBA-sanctioned races. You must decide whether to wear a hel- met while you ride for recreation. You should know that a helmet could help pro- tect you in certain kinds of accidents and that it could injure you in others.A helmet is designed to provide some head protection. Although helmets cannot protect against all foreseeable impacts, a helmet might reduce your injuries in a col- lision with a boat or other obstacle.A helmet may have potential safety haz- ards, as well. Falling into the water could risk the chance of the helmet catching water, commonly known as “bucketing,” and the resulting strain on your neck could cause choking, severe and perma- nent neck injuries, or death. A helmet could also increase the risk of an accident if it reduces your vision or hearing, or if it distracts you or increases your fatigue. How should you decide if a helmet’s potential safety benefits outweigh its potential risks for you? Consider your par- ticular riding conditions. Consider factors such as your riding environment and your riding style and ability. Also consider the likelihood of traffic congestion, and the water surface conditions. If you decide to wear a helmet based upon your riding cir- cumstances, choose one carefully. Look for a helmet designed for personal water- craft use, if possible. Consider a helmet meeting Snell or DOT standards. If you will be engaging in closed-course compe- tition, follow the helmet requirements of the sanctioning organization.q NEVER operate the watercraft after con- suming alcohol or taking other drugs.q For reasons of safety and proper care of the watercraft, always perform the pre- operation checks listed on page 3-5 before operating the watercraft.q The operator and passengers should always keep both feet in the footwell when the watercraft is in motion. Lifting your feet increases your chances of losing your balance, and your feet being hit by objects outside the watercraft. Do not give a ride to children if their feet cannot reach the floor of the footwell.q Passengers should firmly hold on to the person in front of them.q Always consult your doctor on whether it is safe for you to ride this watercraft if you are pregnant or in poor health.E1-11]]></page><page Index="19" isMAC="true"><![CDATA[q Donotattempttomodifythiswatercraft! Modifications to your watercraft may reduce safety and reliability, and render the watercraft unsafe or illegal for use.q Attach the engine shut-off cord (lanyard) to wrist and keep it free from the handle- bars so that the engine stops if the opera- tor falls off. After riding, remove the engine shut-off cord from the watercraft to avoid accidental starting or unauthorized use by children or others.q Scan carefully for swimmers and stay away from swimming areas. Swimmers are hard to see and you could acciden- tally hit someone in the water.q Avoid being hit by another boat! You should always take the responsibility to watch for traffic; other boaters may not be watching for you. If they do not see you, or you maneuver more quickly than other boaters expect, you risk a collision.q Maintain a safe distance from other boats or watercraft, and also watch for boats’ ski ropes or fishing lines. Obey the “Rules of the Road,” and be sure to check behind you before making a turn. (See Rules of the Road on pages 1-16 to 1-19.)q This watercraft is included in the Class A inboard boat classification of the U.S. Coast Guard. A watercraft of this type MUST carry a fire extinguisher of a B-1 classification, with a capacity of two pounds or more when navigating in waters under Coast Guard jurisdiction. In addition, most state and local boating laws also require that the fire extinguisher be approved by the USCG.EJU01381Recommended equipmentThe following items should be carried on board your watercraft:q Sound-signaling deviceYou should carry a whistle or other sound- signaling device that can be used to sig- nal other boats. See Rules of the Road for more information.q Visual distress signalsIt is recommended that a USCG approved pyrotechnic device be stored in a water- proof container on your watercraft. A mir- ror can also be used as an emergency signal. Contact your Yamaha dealer or the Coast Guard for more information.q WatchA watch is helpful so you will know how long you have been operating.q TowlineA towline can be used to tow a disabled watercraft in an emergency.EF0P030101-12]]></page><page Index="20" isMAC="true"><![CDATA[EEJU01202Hazard informationq When transporting or storing your water- craft, always place the fuel cock knob in the “OFF” position, otherwise gasoline may overflow from the carburetor.q Never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monoxide, a colorless, odorless gas that may cause loss of consciousness and death within a short time. Always operate the watercraft in an open area.q Donotstartengineonlanduntileveryone is away from stern. Hot water and steam spurting from exhaust outlet can cause serious burns.q Hot muffler surfaces can cause serious burns. Do not touch any muffler surface during or after engine operation. Catalytic converter gets hotter after engine stops.EJU01209Watercraft characteristicsq Jet thrust turns the watercraft. Releasing the throttle completely produces only min- imum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to steer without throttle. You may still have some turning ability immediately after releasing the throttle, but once the engine slows down, the watercraft will no longer respond to han- dlebar input until you open the throttle again or you reach a trolling speed. Prac- tice turning in an open area without obstructions until you have a good feel for this maneuver.q This watercraft are water-jet propelled. The jet pump is directly connected to the engine. This means that jet thrust will pro- duce some movement whenever the engine is running. There is no “neutral” position. You are in either “forward” or “reverse,” depending upon the shift lever position.q Do not use the reverse function to slow down or stop the watercraft as it could cause you to lose control, be ejected, or impact the handlebars.This could increase the risk of back/spinal injury (paralysis), facial injuries, and bro- ken legs, ankles, and other bones. You could also damage the shift mechanism.1-13]]></page><page Index="21" isMAC="true"><![CDATA[Eq Reverse can be used to slow down or stop during slow speed maneuvering, such as when docking. Once the engine is idling, shift to reverse and gradually increase engine speed. Make sure that there are no obstacles or people behind you before shifting into reverse.q Keep away from intake grate 1 while the engine is on. Items such as long hair, loose clothing, or PFD straps can become entangled in moving parts resulting in severe injury or drowning.q Never insert any object into the jet thrust nozzle 2 while the engine is running. Severe injury or death could result from coming in contact with the rotating parts of the jet pump.q Stop the engine and remove the clip 3 from the engine shut-off switch 4 before removing any debris or weeds, which may have collected around the jet intake.EJU01161Water-skiingYou can use the watercraft for water-ski- ing if it has the seating capacity to carry the operator, a rearward-facing spotter, and the water-skier when he or she is not skiing.The watercraft must also have a cleat 5 designed to pull a ski tow rope; do not attach the tow rope to any other location.It is the watercraft operator’s responsibility to be alert to the safety of the water-skier and others. Know and follow all state and local water-skiing regulations in effect for the waters in which you will be operating.The operator should be comfortable car- rying passengers before attempting to pull a skier.The following are some important consid- erations for minimizing risks while water-ski- ing.q The skier should wear an approved PFD,preferably a brightly colored one so boatoperators can see the skier.q Theskiershouldwearprotectiveclothing.Severe internal injuries can occur if water is forced into body cavities as a result of falling into the water. Normal swimwear does not adequately protect against forceful water entry into rectum or vagina. The skier should wear a wetsuit bottom or clothing that provides equivalent protec- tion.1-14]]></page><page Index="22" isMAC="true"><![CDATA[q A second person should be on board as a spotter to watch the skier; in most states it is required by law. Let the skier direct the operator’s control of speed and direction with hand signals.The spotter should sit securely on the passenger seat and hold onto the hand- grip with feet firmly on the footrest for proper balance while facing to the rear to watch the skier’s hand signals and his or her condition.1 Handgrip2 Footrestq Your control while pulling a skier isaffected by the skier’s ability, as well as water and weather conditions.q When preparing to pull a skier, operate the watercraft at the slowest possible speed until the watercraft is well away from the skier and slack in the towrope is taken up. Make sure that the rope is not looped around anything.After checking that the skier is ready and that there is no traffic or other obstacles, apply enough throttle to raise the skier.q Make smooth, wide turns. The watercraft is capable of very sharp turns, which could exceed the abilities of the skier. Keep the skier at least 50m (150ft), about twice the distance of a standard towrope, from any potential hazard.q Bealerttothehazardofthetowropehan- dle snapping back at the watercraft when the skier falls or is unable to get up on the skis.q Towing heavy or bulky objects other than skiers, such as another boat or watercraft, can cause loss of steering control and create a hazardous condition. If you must tow another boat in an emergency situa- tion, operate slowly and cautiously.1-15E]]></page><page Index="23" isMAC="true"><![CDATA[EEJU01180Steering and sailing rulesWhenever two vessels on the water meet one another, one vessel has the right-of- way; it is called the “stand-on” vessel. The vessel that does not have the right-of-way is called the “give-way” or “burdened” vessel. These rules determine which vessel has the right-of-way, and what each vessel should do.Stand-on vesselThe vessel with the right-of-way has the duty to continue its course and speed, except to avoid an immediate collision. When you maintain your direction and speed, the other vessel will be able to deter- mine how best to avoid you.Give-wayvesselThe vessel which does not have the right- of-way has the duty to take positive and timely action to stay out of the way of the stand-on vessel. Normally, you should not cross in front of the vessel with the right-of- way. You should slow down or change direc- tions briefly and pass behind the other ves- sel. You should always move in such a way that the operator of the other vessel can see what you are doing.The General Prudential Rule regarding the right-of-way is that if a collision appears unavoidable, neither boat has the right-of- way. Both boats must avoid the collision.In other words, follow the standard rules except when a collision will occur unless both vessels try to avoid each other. If that is the case, both vessels become give-way vessels.Rules of the RoadYamaha watercraft is legally consid- ered a powerboat. Operation of the watercraft must be in accordance with the rules and regulations governing the waterway on which it is used.Just as there are rules that apply when you are driving on streets and highways, there are waterway rules that apply when you are operating your watercraft. These rules are used internationally, and are also enforced by the United States Coast Guard and local agencies. You should be aware of these rules, and follow them whenever you encounter another vessel on the water.Several sets of rules prevail according to geographic location, but are all basically the same as the International Rules of the Road. The rules presented here in this Owner’s/Operator’s Manual are condensed, and have been provided for your conve- nience only. Consult your local U.S. Coast Guard Auxiliary or Department of Motor Vehicles for a complete set of rules govern- ing the waters in which you will be operating your watercraft.1-16]]></page><page Index="24" isMAC="true"><![CDATA[ERules when encountering vesselsThere are three main situations that you may encounter with other vessels which could lead to a collision unless the Steering Rules are followed:Meeting: you are approaching another vessel head-onCrossing: you are traveling across another vessel’s pathOvertaking: you are passing or being passed by another vesselIn the following illustration, your watercraft is in the center. You should give the right-of- way to any vessels shown in the white area (you are the give-way vessel). Any vessels in the shaded area must yield to you (they are the give-way vessels). Both you and the meeting vessel must alter course to avoid each other.MeetingIf you are meeting another power vessel head on, and are close enough to run the risk of collision, neither of you has the right- of-way! Both of you should alter course to avoid an accident. You should keep the other vessel on your port (left) side. This rule does not apply if both of you will clear one another if you continue on your set course and speed.CrossingWhen two power-driven vessels are crossing each other’s path close enough to run the risk of collision, the vessel which has the other on the starboard (right) side must keep out of the way of the other. If the other vessel is on your starboard (right) side, you must keep out of its way; you are the give- way vessel. If the other vessel is on your port (left) side, remember that you should maintain course and direction, provided the other vessel gives you the right-of-way as it should.1-17]]></page><page Index="25" isMAC="true"><![CDATA[EOvertakingIf you are passing another vessel, you are the give-way vessel. This means that the other vessel is expected to maintain its course and speed. You must stay out of its way until you are clear of it. Likewise, if another vessel is passing you, you should maintain your speed and direction so that the other vessel can steer itself around you.Other special situationsThere are three other rules you should be aware of when riding your watercraft around other vessels.Narrow channels and bendsWhen navigating in narrow channels, you should keep to the right when it is safe and practical to do so. If the operator of a power- driven vessel is preparing to go around a bend that may obstruct the view of other water vessels, the operator should sound a prolonged blast of four to six seconds on the whistle. If another vessel is around the bend, it too should sound the whistle. Even if no reply is heard, however, the vessel should still proceed around the bend with caution. If you navigate such waters with your water- craft, you will need to carry a portable air horn, available from local marine supply stores.Fishing vessel right-of-wayAll vessels fishing with nets, lines or trawls are considered to be “fishing vessels” under the International Rules. Vessels with trolling lines are not considered fishing ves- sels. Fishing vessels have the right-of-way regardless of position. Fishing vessels can- not, however, impede the passage of other vessels in narrow channels.Sailing vessel right-of-waySailing vessels should normally be given the right-of-way. The exceptions to this are: 1. When the sailing vessel is overtaking thepower-driven vessel, the power-drivenvessel has the right-of-way.2. Sailing vessels should keep clear of anyfishing vessel.3. In a narrow channel, a sailing vesselshould not hamper the safe passage of a power-driven vessel that can navigate only in such a channel.Reading buoys and other markersThe waters of the United States are marked for safe navigation by the lateral system of buoyage. Simply put, buoys and markers have an arrangement of shapes, colors, numbers and lights to show which side of the buoy a boater should pass on when navigating in a particular direction. The markings on these buoys are oriented from the perspective of being entered from seaward (the boater is going towards the harbor). Red buoys are passed on your star- board (right) side when proceeding from open water into the harbor, and black buoys are to your port (left) side. An easy way to remember the meaning of the colors is the phrase “red right returning.” When navigat- ing out of the harbor, your position with respect to the buoys should be reversed; red buoys should be to port and black buoys to starboard.Many bodies of water used by boaters are entirely within the boundaries of a particular state. The Uniform State Waterway Marking System has been devised for these waters.1-18]]></page><page Index="26" isMAC="true"><![CDATA[EThis system uses buoys and signs with distinctive shapes and colors to show regu- latory or advisory information. These mark- ers are white with black letters and orange borders. They signify speed zones, restricted areas, danger areas, and general information.Remember, markings may vary by geo- graphic location. Always consult local boat- ing authorities before riding your watercraft in unfamiliar waters.1-19]]></page><page Index="27" isMAC="true"><![CDATA[EEJU01181To get more boating safety informationBe informed about boating safety. Addi- tional publications and information can be obtained from many organizations, including the following.United States Coast GuardConsumer Affairs Staff (G-BC)Office of Boating, Public, and Consumer AffairsU.S. Coast Guard Headquarters Washington, D.C. 20593-0001Boating Safety Hotline: 1-800-368-5647Other sourcesYou can find local rules by contacting the National Association of State Boating Law Administrators, or your local Power Squad- ron.Watercraft Education andTrainingThe Online Boating Safety Course, avail- able through the watercraft section of the yamaha-motor.com website, is a free, 50 question learning course available to the public. Upon successful completion of 80 percent or better, the user can request a certificate of completion by mail or can download one immediately. The Online Boating Safety Course, provided by the Boat/US Foundation, is approved by the National Association of State Boating Law Administrators (NASBLA) and recognized by the United States Coast Guard. This course meets the education requirement for those states that recognize non-proctored, NASBLA-approved courses.Yamaha is the watercraft industry’s lead- ing manufacturer to build awareness and support for boating education. In 1997, Yamaha launched its GET W.E.T. (Water- craft Education and Training) initiative and has since reached out to over one million Americans promoting the benefits of boating education.1-20The Online Boating Safety Course: http://www.boatus.com/onlinecourse/]]></page><page Index="28" isMAC="true"><![CDATA[EJU01006Enjoy your watercraft responsiblyYou share the areas you enjoy when riding your watercraft with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, waters, and wildlife with respect and courtesy.Whenever and wherever you ride, think of yourself as the guest of those around you. Remember, for example, that the sound of your watercraft may be music to you, but it could be just noise to others. And the excit- ing splash of your wake can make waves others won’t enjoy. Avoid riding close to shoreline homes and waterfowl nesting areas or other wildlife areas, and keep a respectful distance from fishermen, other boats, swimmers, and populated beaches. When travel in areas like these is unavoid- able, ride slowly and obey all laws.Remember that pollution can be harmful to the environment. Do not refuel or add oil where a spill could cause damage to nature. Remove your watercraft from the water and move it away from the shoreline before refu- eling. And keep your surroundings pleasant for the people and wildlife that share the waterways: don’t litter!When you ride responsibly, with respect and courtesy for others, you help ensure that our waterways stay open for the enjoy- ment of a variety of recreational opportuni- ties.1-21E]]></page><page Index="29" isMAC="true"><![CDATA[EJU01007Location of main components ..............2-1Operation of controls and otherfunctions ...................................................2-5Rear seat ................................................2-5Front seat ............................................... 2-6 2 Hood .......................................................2-7Fuel tank filler cap ..................................2-8Oil tank filler cap .....................................2-8Fuel cock knob .......................................2-9 Engine stop switch ...............................2-10 Engine shut-off switch ..........................2-10 Choke knob ..........................................2-10 Throttle lever ........................................2-11Start switch ...........................................2-11 Cooling water pilot outlet .....................2-12 Steering system ...................................2-12Tilt lever ................................................2-13Shift lever .............................................2-14 Quick Shift Trim System (QSTS)selector .................................................2-15 Handgrip ...............................................2-16 Engine overheat warning system ........2-17 Exhaust temperature warningsystem ..................................................2-19 Multifunction meter ...............................2-20 PADLOC (Programmable digitallocking ignition) ....................................2-21 Tachometer ..........................................2-23 Speedometer .......................................2-24Fuel meter ............................................2-24 Engine oil meter ...................................2-25Clock ....................................................2-25Hour meter ...........................................2-26Trip timer ..............................................2-26 Tripmeter ..............................................2-27Fuel warning indicator ..........................2-27Oil warning indicator ............................2-28 Engine overheat warning indicator ......2-28 Exhaust temperature warningindicator ................................................2-29 Battery warning indicator .....................2-29 Storage compartments ........................2-30FEATURES AND FUNCTIONSE]]></page><page Index="30" isMAC="true"><![CDATA[EEJU01008Location of main components1 HandlebarsUse to control direction.2 FootwellUse to place feet for balance.3 FootrestTo keep proper balance while facing to the rear to watch the skier.4 Bow eyeUse to attach rope for transporting, mooring or towing the watercraft in an emergency.5 Hood6 Front seat7 Rear seat8 Sponsons9 Gunwale2-1]]></page><page Index="31" isMAC="true"><![CDATA[E1 Fuel tank filler cap2 Rope holes3 Intake gratePrevents debris from getting into the jet pump.4 Speed sensor5 CleatUse to attach a towrope for pulling water-skier,or a rope for mooring the watercraft.6 HandgripUse for support when boarding the watercraft or when seated facing rearward and acting as a spotter for a water-skier.7 Reverse gateControls direction of jet thrust when in reverse.8 Stern drain plugsUse to drain water in the bilge when the water- craft is on dry land.9 Jet thrust nozzleChanges the direction of jet thrust according to handlebar position.0 Ride plate2-2]]></page><page Index="32" isMAC="true"><![CDATA[E1 Engine stop switchPush to stop the engine normally.2 ClipInsert into the engine shut-off switch to enable starting of the engine.Remove to stop the engine or prevent acci- dental starting of the engine or unauthorized use of the watercraft.3 Quick Shift Trim System (QSTS) selector Use to select the trim angle of the watercraft.4 QSTS shift lock lever5 Engine shut-off switchRemove the clip to stop the engine and dis-able it from starting.6 Start switchPush to start the engine.7 Fuel cock knobUse to select either normal or reserve fuel flow from the fuel tank to the carburetors, or to shut off fuel flow.8 Choke knobUse to start a cold engine.9 Engine shut-off cord (lanyard)Attach to wrist so that the engine stops if the operator falls off the watercraft.0 Adjustable rearview mirrorsA Multifunction meterUse to check watercraft operation.B Shift leverUse to put the watercraft into forward or reverse.C Throttle leverUse to accelerate and decelerate.D Tilt leverUse to adjust the tilt of the handlebars.E Glove compartment2-3]]></page><page Index="33" isMAC="true"><![CDATA[E1 Spark plugs/Spark plug caps2 Electrical boxProtects electrical components from water.3 Flush hose connectorUse to flush the engine cooling water pas- sages.4 Spark plug lead5 Muffler6 Fuel filter7 Fuel tank8 Oil tank 9 Battery2-4]]></page><page Index="34" isMAC="true"><![CDATA[EEJU01009Operation of controls and other functionsEJU01211Rear seatTo remove the rear seat:Pull the rear seat latch 1 up, and then pull the seat off.To install the rear seat:Insert the projections on the front of the seat into the stays on the deck, and then push the rear of the seat down to lock it in place securely.2-5]]></page><page Index="35" isMAC="true"><![CDATA[EEJU01212Front seatTo remove the front seat:1. Remove the rear seat.2. Pull the front seat latch 2 up, and thenpull the seat off.To install the front seat:1. Insert the projections on the front of the seat into the stays on the deck, and then push the rear of the seat down to lock it in place.2. Install the rear seat.Make sure that the seats are properly secured before operating the watercraft.@NOTE: @2-6]]></page><page Index="36" isMAC="true"><![CDATA[EEJU01213HoodTo open the hood, pull the latch 1 up, and then lift the hood up.To close the hood, push the hood down to lock it in place.Make sure that the hood is properly secured before operating the watercraft.@NOTE: @2-7]]></page><page Index="37" isMAC="true"><![CDATA[EEJU01012Fuel tank filler capTo remove the fuel tank filler cap 1, turn it counterclockwise.Make sure that the fuel tank filler cap isproperly secured before operating the water-craft.@EJU01214Oil tank filler capTo remove the oil tank filler cap:1. Open the hood. (See page 2-7 for hood.)2. Turn the filler cap 2 counterclockwise.To install the oil tank filler cap:Install the filler cap, and then close the hood.Make sure that the oil tank filler cap andhood are properly secured before operatingthe watercraft.@NOTE: @NOTE: @2-8]]></page><page Index="38" isMAC="true"><![CDATA[E2-9EJU01014Fuel cock knobThe fuel cock supplies fuel from the fuel tank to the carburetors.The fuel cock knob 1 positions are explained as follows and are shown in the illustration.OFF:With the fuel cock knob in this position, fuel does not flow. Always turn the fuel cock knob to this position when the engine is not running.ON:With the fuel cock knob in this position, fuel flows to the carburetors. Turn the fuel cock knob to this position when starting the engine and operating the watercraft.RES:This indicates reserve. With the fuel cock knob in this position, the fuel reserve is made available. Turn the fuel cock knob to this position if you run out of fuel while oper- ating the watercraft. When this occurs, refuel as soon as possible and be sure to turn the fuel cock knob back to “ON”!]]></page><page Index="39" isMAC="true"><![CDATA[EJU01015Engine stop switchPush this switch 1 (red button) to stop the engine normally.EJU01016Engine shut-off switchInsert the clip 1, on the end of the engine shut-off cord 2, under the engine shut-off switch 3 (black button). The engine will stop automatically when the clip is removed from the switch, such as if the operator falls off the watercraft.@q Alwaysattachtheengineshut-offcord to your wrist and the clip to the engine shut-off switch BEFORE starting the engine.q To prevent accidental starting of the engine or unauthorized use by chil- dren or others, always remove the clip from the shut-off switch when the engine is not running.@EJU01215Choke knobStarting a cold engine requires a richer air-fuel mixture, which is supplied by the choke.Pull the knob 1 out to turn the choke on. Push the knob in to turn the choke off.EWARNING2-10]]></page><page Index="40" isMAC="true"><![CDATA[EEJU01018Throttle leverSqueeze the throttle lever 1 to increase engine speed.Release the throttle lever to decrease engine speed or to return it to the idle posi- tion.EJU01216Start switchPush the start switch 1 (green button) to start the engine.q The engine will not start when the clip is removed from the engine shut-off switch.q The engine will not start if the “LOCK” mode of the multifunction meter has been selected. (See page 2-22 for “PADLOC” mode selection procedures.)@NOTE: @2-11]]></page><page Index="41" isMAC="true"><![CDATA[EEJU01020Cooling water pilot outletThis watercraft is equipped with a cooling water pilot outlets.When the engine is running, cooling water is circulated in the engine, and then it is discharged from the pilot outlets.To check for proper operation of the cool- ing system, check that water is being dis- charged from the pilot outlets. If water is not being discharged from the outlets, cooling water may not be circulating in the engine. When this occurs, stop the engine and check for the cause. (See pages 2-17 and 5-4 for further instructions.)If the cooling water passages are dry, it willtake about 20 seconds for the water to reachthe outlet after the engine is started.@EJU01021Steering systemYour watercraft can be steered by turning the handlebars 1 the same direction you wish to travel.When the handlebars are turned, the angle of the jet thrust nozzle 2 is changed, and the direction of the watercraft is changed accordingly. Since the strength of the jet thrust determines the speed and direction of a turn, the throttle must always be open when attempting a turn, except at trolling speed.NOTE: @2-12]]></page><page Index="42" isMAC="true"><![CDATA[EEJU01217Tilt leverThe tilt lever 1 is located in front of the glove compartment and is used to adjust the tilt of the handlebars.To adjust the tilt, pull the tilt lever up, and then move the handlebars up or down to the desired position.@q Never touch the tilt lever during opera- tion, otherwise the handlebars may suddenly change position, which may lead to an accident.q Be sure to fasten the tilt lever properly after adjusting the handlebar position. If the handlebars are not properly fas- tened, they may suddenly change position, which may lead to an acci- dent.@WARNING2-13]]></page><page Index="43" isMAC="true"><![CDATA[EJU01218Shift leverThe shift lever is located on the starboard side of the watercraft and is used to control the reverse gate, which allows the watercraft to move into reverse or forward.When in the reverse position, the water- craft can be launched from a trailer, or backed up out of tight spots where you can- not turn around easily.To shift into reverse:E1. 2.@qqq qq@Release the throttle, and then let the engine speed return to idle.Pull the shift lever toward you.Make sure that the throttle is com- pletely released and that the engine is at idle before shifting into reverse.Do not use the reverse function to slow down or stop the watercraft as it could cause you to lose control, be ejected, or impact the handlebars.Use reverse for slow-speed maneuver- ing only.Make sure that there are no obstacles or people behind you before shifting into reverse. Donottouchthereversegatewhilethe shift lever is being operated, otherwise you could be pinched.WARNING2-14To shift into forward:1. Release the throttle, and then let the engine speed return to idle.2. Push the shift lever away from you.]]></page><page Index="44" isMAC="true"><![CDATA[EEJU01022Quick Shift Trim System (QSTS) selectorThe QSTS selector 1 is located at the left handlebar grip and is used to adjust the trim angle of the watercraft.Operating the QSTS selector changes the angle of the jet thrust nozzle vertically. This changes the trim angle of the watercraft.There are 5 positions: 2 bow down posi- tions A and B, neutral “N,” and 2 bow up positions C and D.To change the trim angle:1. Reduce engine speed to 3,400 r/min or less.2. Squeeze the shift lock lever 2, and then turn the QSTS selector to the desired position.3. Release the shift lock lever to lock the QSTS selector.@Do not turn the QSTS selector while operating the watercraft at full throttle, otherwise damage could occur to the QSTS.@The neutral “N” position will provide good performance for most operating conditions.To enhance particular types of perfor- mance, select bow down or bow up.CAUTION:2-15]]></page><page Index="45" isMAC="true"><![CDATA[EEJU01023Bow downTurn the grip to A or B and the bow will go down while the watercraft is on plane.Bow down puts more of the bow in the water. This gives the watercraft more “hook,” which enhances turning performance. This position will also help the watercraft get up on plane more quickly.At higher speeds, however, the watercraft will have greater tendency to “bow steer” and follow waves and wakes in the water. Fuel economy and maximum speed are also reduced.EJU01024Bow upTurn the grip to C or D and the bow will go up while the watercraft is on plane.Bow up puts less of the bow in the water. There is less water resistance, so straight- ahead acceleration when on plane and top speed are enhanced.In some conditions, however, the water- craft may tend to “porpoise” (hop in the water). If the watercraft is porpoising, choose neutral or bow down.EJU01219HandgripThe handgrip 1 provides a handhold for boarding the watercraft and for a spotter when facing rearward.@Do not use to tow objects, lift watercraft,or attach tie downs, otherwise damagecould occur.@CAUTION:2-16]]></page><page Index="46" isMAC="true"><![CDATA[EEJU01329Engine overheat warning systemThe model has an overheat warning device. If the engine starts to overheat, the warning light, indicator and “W.TEMP” on the meter begin to blink and the buzzer sounds intermittently. If this happens, reduce the engine speed and return to beach at low speed. If there is no water dis- charge at the cooling water pilot outlet while the engine is running, check the jet intake and impeller for clogging.@Before attempting to remove weeds or debris from the intake grate or impeller, shut the engine off and remove the clip from the engine shut-off switch. Severe injury or death could result from coming in contact with the rotating parts of the jet pump.@@This model is equipped with a catalytic converter.q Return to shore at low speed if theoverheat warning indicator and buzzer are on, and the display shows “W.TEMP.” If you ignore these signals, the engine will stop running and can- not be restarted until the exhaust sys- tem cools.q Have your watercraft inspected and serviced by a Yamaha dealer if the engine stopped due to overheating.@WARNINGCAUTION:2-17]]></page><page Index="47" isMAC="true"><![CDATA[EIf the initial overheat warning is ignored, engine and exhaust system heat can increase, particularly if the watercraft contin- ues to be operated at higher speed. If so, the warning indicators and buzzer will change from intermittent to constantly on and the overheat system will stop ignition to the engine to reduce the risk of severe over- heating. The engine cannot be restarted until it cools down, so it may be necessary to have the watercraft towed back to the beach. Refer to “Towing the watercraft” on page 5-7.q The buzzer stops sounding if any button on the meter is pressed.q Ask a Yamaha dealer to inspect the watercraft if there is no apparent reason for overheating.@NOTE: @2-18]]></page><page Index="48" isMAC="true"><![CDATA[EEJU01331Exhaust temperature warning systemThis model has an exhaust temperature warning device. If the exhaust temperature gets too hot, the warning light, indicator and “EXHST” will blink. The buzzer also sounds intermittently. If this happens, reduce engine speed and return to the beach at low speed. Allow the exhaust system to cool.@Hot muffler surfaces can cause serious burns. Do not touch any muffler surface during or after engine operation. The cat- alytic converter gets hotter after the engine stops.@@This model is equipped with a catalytic converter. Return to shore at low speed (below 4,000 r/min) if the warning indica- tor and buzzer are on, and the display shows “EXHST.” Have your watercraft inspected and serviced by a Yamaha dealer if the engine stopped due to over- heating.@q The buzzer stops sounding if any button on the meter is pressed.q Ask a Yamaha dealer to inspect the watercraft if there is no apparent reason for overheating.@WARNINGCAUTION:NOTE: @2-19]]></page><page Index="49" isMAC="true"><![CDATA[EJU01332Multifunction meterThis meter contains following functions for help and convenience in operating the watercraft.1 “MODE” button2 “SET” button3 “CODE” setting buttons4 Tachometer5 Speedometer6 Fuel meter7 Engine oil meter8 Display for Clock, Hour meter, Trip meter andTrip timer9 Warning light0 Display for PADLOC and direction of warningindicatorA Battery warning indicatorB Exhaust temperature warning indicatorC Engine overheat warning indicatorD Fuel warning indicatorE Oil warning indicator@q Do not run the engine over 4,000 r/min to check the meter for operation on land. The engine could overheat or the catalytic converter could result in seri- ous damage.q Use the specified resistor-type spark plugs and caps, otherwise the meter may function erratically.@The demonstration mode display starts showing after the engine starts. Then all dis- plays light up and the buzzer sounds twice. The meter will operate normally after a few seconds. The current display will continue to operate for 30 seconds after the engine stops.@ECAUTION:NOTE: @2-20]]></page><page Index="50" isMAC="true"><![CDATA[EEJU01222PADLOC (Programmable digital locking ignition)This feature is provided to deter unautho- rized use.The function allows you to choose either “START” or “LOCK” mode, as the situation requires, much as you would use an ignition key in a motor vehicle. If you have previously chosen “LOCK” mode, the engine will not start unless the right code is put in to select “START” mode.If you do not use the PADLOC system, it is unnecessary to perform the initial setting of the PADLOC. In this case, the “START” mode is automatically selected.@EJU01223PADLOC initial setting1. Disconnect the blue connector 1 behind the front storage compartment.2. After the warning light turns on, press the “MODE” button for at least 3 seconds until the display shows “COdE.” You are ready to set your code.NOTE: @2-21]]></page><page Index="51" isMAC="true"><![CDATA[3. Select your four-letter code by pressing the “A/SET,” “B,” or “C” buttons in a desired sequence.If you do not press a button for more than 10 seconds, the display automatically turns off. This cancels the process of setting a code.@4. After code setting is complete, the buzzer will sound 3 times and the display will show “SET.” Lastly, the display turns off and the warning light turns on again. After the meter has displayed this sequence, connect the blue connector again.q Your own code is kept even if the battery terminal is disconnected.q Ifyouforgetyourowncode,orifyouwant to change the code, do this initial setting procedure again from the beginning.@EJU01224Selecting “PADLOC” modeSelecting the desired mode can only be done after the initial setting has been done and while the display is not lit.1. Press the “MODE” button until the meterdisplays the current mode, “START” or “LOCK.”2. With “START” or “LOCK” displayed, press the “MODE” button continuouslyfor about 3 seconds until the display changes to “COdE.”E2-22NOTE: @NOTE: @]]></page><page Index="52" isMAC="true"><![CDATA[3. Enter your four-letter code by pressing the “A/SET,” “B,” or “C” buttons in the right sequence.If you do not press a button for more than 10 seconds, the display automatically turns off. This cancels the process of selecting the mode.@4. If the code entered is correct, the mode will change from the previous mode to either “START” or “LOCK.” Then the mode display and buzzer will operate for 2 seconds.q Once you select a mode, the mode will not change unless you perform this mode selection sequence again.q If the wrong code is entered, the mode display shows “ERROR” for 2 seconds and the buzzer will sound 5 times. Then the display returns to “COdE.”@ENOTE: @NOTE: @2-23EJU01225TachometerThe engine speed (r/min) is displayed by segments. Each segment indicates a 200 r/min increment.]]></page><page Index="53" isMAC="true"><![CDATA[EJU01226SpeedometerThe meter shows the watercraft speed against water.EJU01227Fuel meterThe fuel meter is provided for convenient fuel level checking while operating the watercraft.The fuel meter has 4segments which show the amount of fuel remaining in the fuel tank.The indication of the segments differsdepending on your operating condition. Usethe meter as a reference.@ENOTE: @2-24]]></page><page Index="54" isMAC="true"><![CDATA[EEJU01228Engine oil meterThe engine oil meter is provided for con- venient oil level checking while operating the watercraft.The engine oil meter has 3segments which show the amount of oil remaining in the oil tank.The indication of the segments differsdepending on your operating condition. Usethe meter as a reference.@2-25NOTE: @EJU01229ClockA 12-hour clock is provided in this meter.To show the clock, press the “MODE” but- ton until the display shows “CLOCK” while the engine is running.1. When the display shows “CLOCK,” pressthe mode button for at least 3 seconds.2. The buzzer will sound once. The hour display and “SET” start blinking. Then press the “A/SET” button until thedesired hour is displayed.3. Press the “MODE” button again.4. The buzzer will sound once. The minutedisplay and “SET” start blinking. Then press the “A/SET” button until the desired minute is displayed.5. Press the “MODE” button again.]]></page><page Index="55" isMAC="true"><![CDATA[E6. The buzzer will sound twice. The warn- ing light and “SET” blink for 2 seconds. Then the display turns to “CLOCK” and shows the time.If the battery terminal is disconnected, the clock will be reset to 12:00.@EJU01230Hour meterThe hour meter is provided to make it easy to follow the maintenance schedule.The meter shows how many hours of engine operation have elapsed since the watercraft was new.To show the hour meter, press the “MODE” button until the display shows “HOUR.M” while the engine is running.EJU01231Trip timerThe trip timer is provided for counting the time traveled on a given trip.To show the trip timer, press the “MODE” button until the display shows “TRIP.T” while the engine is running.1 Minutes2 Seconds1. When the display shows “TRIP.T,” pressthe “A/SET” button to start counting. Thebuzzer will sound once.2. Press the “A/SET” button again to stopcounting. The buzzer will sound once.3. Press “MODE” button for at least2 seconds to set the time back to 00:00. The buzzer will sound twice. The time display and “TRIP.T” blink for 2 seconds. Now it is ready to start counting.2-26NOTE: @]]></page><page Index="56" isMAC="true"><![CDATA[EEJU01163TripmeterA tripmeter is provided for measuring the approximate distance traveled.To show the tripmeter, press the “MODE” button until the display shows “TRIP” while the engine is running. After showing “TRIP,” the display turns to “.MILE.”1. When the display shows “.MILE,” press the “MODE” button for at least 2 seconds.2. The buzzer will sound twice. The warn- ing light and “.MILE” blink for 2 seconds, and “000” is displayed. Now the meter will start to measure the distance you travel.3. When the tripmeter begins measuring the distance traveled, the “.” to the left of “MILE” on the display will blink.Measured distance may vary depending on the water surface conditions, and wind direc- tion. The measured distance should be used for a reference.@NOTE: @2-27EJU01232Fuel warning indicatorIf the fuel remaining in the tank drops to about 17 L (4.5 US gal, 3.7 Imp gal), the lowest fuel level segment, the fuel warning indicator, “FUEL” and the warning light begin to blink. The buzzer also starts sound- ing intermittently.]]></page><page Index="57" isMAC="true"><![CDATA[EEJU01233Oil warning indicatorIf the oil remaining in the tank drops to about 1.4 L (0.37 US gal, 0.31 Imp gal) or the oil filter is clogged, the lowest oil level segment, the oil warning indicator, “OIL” and the warning light begin to blink. The buzzer also starts sounding intermittently.If the oil warning indicator begins to blink, refill with engine oil as soon as possible.If the warning indicator blinks with adequateoil in the tank, check the oil filter for clog-ging.@EJU01333Engine overheat warningindicatorIf the engine starts to overheat, the engine overheat warning indicator, “W.TEMP” and the warning light begin to blink. The buzzer also starts sounding intermittently.If the engine continues to be operated at higher speed after the warning system indica- tors have come on intermittently, the warning indicator, “W.TEMP” and the warning light will change to being on continuously. Also, the engine will stop and the buzzer will sound con- tinuously. Refer to “Engine overheat warning system” on page 2-17.When the warnings overlap each other, their priority is as follows.1. Final overheat2. Exhaust temperature3. Initial overheat4. Oil5. Fuel6. Battery@NOTE: @NOTE: @2-28]]></page><page Index="58" isMAC="true"><![CDATA[E2-29EJU01334Exhaust temperature warning indicatorIf the exhaust system becomes too hot, the exhaust temperature warning indicator, “EXHST” and warning light will blink. Also, the buzzer will start sounding intermittently. Refer to “Exhaust temperature warning sys- tem” on page 2-19.EJU01235Battery warning indicatorIf the battery voltage becomes less than 11.5 volts, the battery warning indicator, “VOLT” and the warning light begin to blink. The buzzer also starts sounding.If this happens during operation, beach the watercraft. Then recharge the battery and have the charging system inspected by a Yamaha dealer.]]></page><page Index="59" isMAC="true"><![CDATA[EEJU01236Storage compartmentsA front storage compartment, a glove compartment, and seat storage compart- ments are provided.q Makesurethatthestoragecompartments are properly secured before operating the watercraft.q The storage compartments are not designed to be waterproof. If you carry objects that must be kept dry, such as the manuals, put them in a waterproof bag.@EJU01237Front storage compartmentThe front storage compartment 2 is located at the bow.To open the front storage compartment, pull the hood latch 1 up, and then open the hood.To close the front storage compartment, push down on the rear of the hood until it latches securely.The front storage compartment can beremoved to access the engine compart-ment.@NOTE: @NOTE: @2-30Front storage compartment:Capacity: 56 L (15 US gal, 12 Imp gal) Load limit: 5 kg (11 lb)]]></page><page Index="60" isMAC="true"><![CDATA[EJU01038Glove compartmentA glove compartment 4 is located in front of the seat.To open the glove compartment, slide the latch 3 toward you, and then lift up the lid.To close the glove compartment, push the lid down until it locks securely.E2-31Glove compartment:Capacity: 1.7 L (0.45 US gal, 0.37 Imp gal) Load limit: 1 kg (2.2 lb)EJU01239Seat storage compartmentThe seat storage compartment 5 is located under the rear seat.To open the seat storage compartment, remove the rear seat. (See page 2-5 for rear seat.)Seat storage compartment:Capacity: 30 L (8 US gal, 6.6 Imp gal) Load limit: 9 kg (19.8 lb)]]></page><page Index="61" isMAC="true"><![CDATA[EJU01040OPERATIONFuel and oil ...............................................3-1 Gasoline .................................................3-1 2-stroke engine oil ..................................3-2 Filling the fuel tank .................................3-3 Filling the oil tank ...................................3-4Pre-operation checks ..............................3-5 Pre-operation check list .........................3-5 Pre-operation check points ....................3-6Operation ................................................3-14 Engine break-in ....................................3-14 Launching the watercraft .....................3-16 Starting the engine ...............................3-16 3 Stopping the engine .............................3-19 Leaving the watercraft .........................3-19Operating your watercraft ....................3-20 Getting to know your watercraft ...........3-20 Learning to operate your watercraft ....3-20 Riding watercraft with passengers ......3-21 Starting the watercraft ..........................3-22 Boarding and starting in deep water ...3-24 Capsized watercraft .............................3-26 Turning the watercraft ..........................3-28 Stopping the watercraft ........................3-30 Beaching the watercraft .......................3-31 Docking the watercraft .........................3-31 Reverse on waterways ........................3-32 Rough water operation ........................3-32Post-operation checks .........................3-33 Transporting ..........................................3-35E]]></page><page Index="62" isMAC="true"><![CDATA[This engine uses Yamaha’s oil injection system, which provides superior lubrication by ensuring the proper oil ratio for all operat- ing conditions. No fuel premixing is neces- sary except during the engine break-in period. Simply pour gasoline into the fuel tank and oil into the oil tank.EJU01203Gasoline@GASOLINE AND ITS VAPORS ARE HIGHLY FLAMMABLE AND EXPLOSIVE! q Do not smoke when refueling, andkeep away from sparks, flames, orother sources of ignition.q Stopenginebeforerefueling.q Refuel in a well-ventilated area. Do notstand or sit on the watercraft whilerefueling in case of fire.q Takecarenottospillgasoline.Ifgaso-line spills, wipe it up immediately with dry rags. Always properly dispose of gasoline-soaked rags.q Avoidoverfillingthefueltank.Stopfill- ing when the fuel level just reaches the bottom of the filler tube. Do not fill up the filler tube because fuel expands as it warms up and could overflow.q Tighten the filler cap securely after refueling.q If you should swallow some gasoline, inhale a lot of gasoline vapor, or get gasoline in your eyes, get immediate medical attention.q If any gasoline spills onto your skin, immediately wash with soap and water. Change clothing if gasoline spills on it.@EEJU01041Fuel and oilWARNING3-1]]></page><page Index="63" isMAC="true"><![CDATA[@q Do not use leaded gasoline. Leaded gasoline can seriously damage the catalytic converter.q Use only fresh gasoline that has been stored in clean containers.@ECAUTION:Recommended gasoline:Regular unleaded gasoline with a mini- mum octane rating of86 (Pump octane number) = (R+M)/2 90 (Research octane number)EJU01043GasoholThere are two types of gasohol: gasohol containing ethanol and that containing meth- anol.Gasohol containing ethanol can be used if ethanol content does not exceed 10 % and the fuel meets minimum octane ratings.Gasohol containing methanol is not rec- ommended by Yamaha because it can cause fuel system damage or engine perfor- mance problems.EJU011872-stroke engine oil@Use only YAMALUBE 2-W oil. Using another oil can seriously damage the cat- alytic converter and other engine compo- nents.@YAMALUBE 2-W is developed for this water- craft and available from a Yamaha dealer.@CAUTION:Recommended engine oil: YAMALUBE 2-W oil onlyNOTE: @3-2]]></page><page Index="64" isMAC="true"><![CDATA[EEJU01045Filling the fuel tank@Be careful when refueling. Avoid getting water or other contaminants in the fuel tank. Contaminated fuel can cause poor running or engine damage.@1. Open the hood and remove the front storage compartment, to check the fuel level. (See page 2-30 for front storage compartment.)2. Open the fuel tank filler cap, and slowly add fuel to the fuel tank.3. Stop filling when the fuel just reaches the bottom of the filler tube on the fuel tank. Do not fill into the filler tube, because fuel could spill out.CAUTION:3-3Fuel tank capacity:Total: 70 L (18.5 US gal, 15.5 Imp gal) Reserve: 12 L (3.2 US gal, 2.7 Imp gal)]]></page><page Index="65" isMAC="true"><![CDATA[EEJU01240Filling the oil tank@q Do not add gasoline to the oil tank. Fire or explosion could result.q Oil in the bilge is a serious fire hazard. Wipe up any spilled oil immediately.@@Do not allow the oil tank to become com- pletely empty. If the oil tank becomes empty the oil injection pump must be bled to ensure proper oil flow, otherwise engine damage may occur. If bleeding of the oil pump is necessary, have a Yamaha dealer bleed it.@1. Open the hood to access the oil tank filler cap. Also, remove all seats to watch the oil level. (See page 2-7 for hood, and 2-5 and 2-6 for rear and front seat.)2. Open the oil tank filler cap, and very slowly add engine oil to the oil tank.3. Stop pouring when the oil just reaches the bottom of the filler tube.WARNINGCAUTION:3-4Oil tank capacity:5.5 L (1.5 US gal, 1.3 Imp gal)]]></page><page Index="66" isMAC="true"><![CDATA[Pre-operation check listBefore operating this watercraft, perform the checks in the following check list. See the accompanying text in this chapter for details on how to perform the checks.@If any item in the pre-operation check list is not working properly, have it inspected and repaired before operating the watercraft, otherwise an accident could occur.@EEJU01346EJU01349Pre-operation checksWARNINGITEMROUTINEPAGEEngine compartmentRemove all seats and front storage compart- ment to ventilate engine compartment. Check for fuel vapors or loose electrical connections3-6BilgeCheck for water and fuel residue and remove if necessary3-7ThrottleCheck that the throttle lever springs back3-10Steering systemCheck for proper steering system operation3-10Shift lever and reverse gateCheck for proper operation3-11Fuel and oilCheck fuel and oil level and add if necessary Check hoses and tanks for leakage3-6Water separatorCheck for water and drain if necessary3-7BatteryCheck electrolyte level and battery condition3-8Front and rear seatsCheck that the seats are properly secured2-5, 2-6Hull/DeckCheck the hull and deck for cracks or other dam- age—Jet unitCheck for debris and remove if necessary3-12Fire extinguisherCheck the condition and replace if necessary3-9Engine shut-off cordCheck condition and replace is frayed or broken3-12SwitchesCheck the start switch, engine stop switch and engine shut-off switch for proper operation when the watercraft is in the water3-13Cooling water pilot outletCheck that water is discharged while the engine is running and the watercraft is in the water3-13Multifunction meterCheck for warning indications and proper opera- tion3-13NOTE: @Pre-operation checks should be made thoroughly each time the watercraft is used. This pro-cedure can be completed in a short time. It is worth the time spent to assure safety and reli-ability.@3-5]]></page><page Index="67" isMAC="true"><![CDATA[EJU01048Pre-operation check pointsEJU01241Engine compartmentVentilate the engine compartment before each use.To ventilate the engine compartment, remove all seats and front storage compart- ment. (See pages 2-5 and 2-6 for front and rear seat, and 2-30 for front storage com- partment.) Allow the engine compartment to remain open for a few minutes to allow any fuel vapors to escape. Also, check for loose electrical connections.@Failure to ventilate the engine compart- ment could result in fire or explosion. Do not start the engine if there is a fuel leak or a loose electrical connection.@EJU01242Fuel and oil systemsCheck the fuel system for leakage, cracks or malfunctions before each use. (See page 4-9 for check points and correct proce- dures.)1. Remove the fuel tank filler cap to releaseany pressure that might have built up inthe fuel tank.2. Remove all seats and front storage com-partment. (See pages 2-5 and 2-6 for front and rear seat, and 2-30 for front storage compartment.)3. Check the fuel and oil levels in the tanks and replenish if necessary. (See pages 3-3 and 3-4 for filling instructions.)EWARNING3-6]]></page><page Index="68" isMAC="true"><![CDATA[EEJU01052Water separatorCheck the water separator 1 for water. Normally the water separator is empty. The water separator retains any water entering through the fuel tank breather hose if the watercraft is capsized.If water remains in the water separator, drain it by removing the drain screw 2. Install the drain screw again after draining the water separator.EJU01053BilgeCheck for moisture and fuel residue in the bilge.Excessive water in the bilge can splash into the carburetor and engine which could cause engine damage.To remove water from the bilge:1. Remove the stern drain plugs.2. Raise the bow of the watercraft until thewater drains.3. After the water has drained, wipe thebilge with dry rags to make sure that thebilge is thoroughly dry.4. Install the drain plugs.@q Make sure that the stern drain plugs are tightened securely before launch- ing the watercraft.q Clean any foreign materials, such as dirt or sand, from the drain plug threads before installing the drain plugs.@CAUTION:3-7]]></page><page Index="69" isMAC="true"><![CDATA[EJU01054BatteryCheck the battery condition and the elec- trolyte level.Check that the battery leads are tightened securely and there is no corrosion on the battery terminals.@The battery must always be fully charged and in good condition. Loss of battery power may leave you stranded. Never operate the watercraft if the battery does not have sufficient power to start the engine or if it shows any other signs of decreased power.@Make sure that the breather hose is prop- erly connected and that it is not damaged or obstructed.Make sure that the battery is securely held in place.1 Positive (+): Red lead2 Negative (–): Black lead3 Breather hoseEWARNING3-8]]></page><page Index="70" isMAC="true"><![CDATA[EJU01164Fire extinguisherCheck that there is a full fire extinguisher on board. The fire extinguisher container 1 is located in the front storage compartment.To open the fire extinguisher container cap 2 turn it counterclockwise.After inserting the fire extinguisher make sure that the container cap is tightened securely.q See the instructions supplied by the fire extinguisher manufacturer for checking the fire extinguisher. Always keep the extinguisher in the fire extinguisher con- tainer.q Alwayscarryafireextinguisheronboard. A fire extinguisher is not standard equip- ment with this watercraft. If you do not have one, contact a Yamaha dealer or a fire extinguisher dealer to obtain one meeting the proper specifications.@EF0P03010NOTE: @3-9Fire extinguisher: Classification: B-1 Capacity: 2 lb or more]]></page><page Index="71" isMAC="true"><![CDATA[EEJU01056ThrottleSqueeze and release the throttle lever several times to make sure that there is no hesitation in its travel. It should be smooth over the complete range, and spring back to the idle position when released.@Before starting the engine, always check the operation of the throttle lever. It should move smoothly through its full range of operation, and should spring back to the idle position when released.@WARNING3-10EJU01244Steering systemCheck for looseness in the handlebars.Turn them as far as possible to the right and left to make sure that operation is smooth and unrestricted throughout the whole range. Make sure that the jet thrust nozzle also changes directions as the han- dlebars are turned, and that there is no free play between the handlebars and the jet thrust nozzle.Check that the tilt adjustment is locked in position. (See Tilt lever on page 2-13.)]]></page><page Index="72" isMAC="true"><![CDATA[EEJU01245Shift lever and reverse gateCheck for proper operation of the shift lever and reverse gate.Make sure that the reverse gate goes down to its stopper position when the shift lever is pulled up.Also, make sure that the reverse gate goes up to its stopper position when shift lever is pushed down.@q Make sure that the throttle is com- pletely released and that the engine is at idle before shifting into reverse.q Do not use the reverse function to slow down or stop the watercraft as it could cause you to lose control, be ejected, or impact the handlebars.q Use reverse for slow-speed maneuver- ing only.q Make sure that there are no obstacles or people behind you before shifting into reverse.q Donottouchthereversegatewhilethe shift lever is being operated, otherwise you could be pinched.@WARNING3-11]]></page><page Index="73" isMAC="true"><![CDATA[EEJU01058Jet unitCarefully check the jet intake for weeds, debris, or anything else that might restrict the intake of water. If the intake is clogged, cavitation could occur, reducing jet thrust, and possibly damaging the jet pump.In some cases, the engine may overheat because of lack of cooling water, and dam- age to the engine could result. Engine cool- ing water is fed to the engine by the jet pump. (See page 5-4 for jet intake cleaning procedures.)@q Keep away from intake grate while engine is on. Items such as long hair, loose clothing, or PFD straps can become entangled in moving parts resulting in severe injury or drowning.q Stop the engine and remove the clip from the engine shut-off switch before removing any debris or weeds, which may have collected around the jet intake.@WARNING3-12EJU01059Engine shut-off cord (lanyard)Check that the engine shut-off cord is not frayed or broken. If the cord is damaged, replace it; never try to repair it or tie it together.]]></page><page Index="74" isMAC="true"><![CDATA[EEJU01060SwitchesCheck the start switch 1, the engine stop switch 2, and the engine shut-off switch 3 for proper operation.To check these switches place the water- craft in the water to provide adequate cooling. Start the engine, and then pull the engine shut-off cord 5 to remove the clip 4 from the engine shut-off switch. Verify that the engine stops immediately. (See pages 3-16 to 3-19 for information on proper operation of the start switch, the engine stop switch and the engine shut-off switch.)3-13EJU01061Cooling water pilot outletCheck that water comes out from the out- lets while the engine is running and the watercraft is in the water.EJU01246Multifunction meterCheck the operation of the multifunction meter. (See pages 2-20 to 2-29 for operation of the meter.)]]></page><page Index="75" isMAC="true"><![CDATA[EEJU01063@OperationWARNINGBefore operating your watercraft, become familiar with all controls. Con- sult your Yamaha dealer about any con- trol or function you do not fully understand. Failure to understand how controls work could cause an accident or prevent you from avoiding an accident.@@Make sure that stern drain plugs aresecurely tightened before launching thewatercraft.@EJU01189Engine break-inThe engine break-in period is essential to allow the various components of the engine to wear and polish themselves to the correct operating clearances. This ensures proper performance and promotes longer compo- nent life.@q For the first tankful of operation, pre- mix a 50:1 mixture of fuel and oil (in addition to the oil in the oil tank).q After break-in, use straight gasoline for normal operation.@1. Launch the watercraft and start the engine. (See pages 3-16 to 3-18 for engine starting procedures.)2. Run the engine at the lowest possible speed for 5 minutes.CAUTION:CAUTION:3-14]]></page><page Index="76" isMAC="true"><![CDATA[E3. Gradually open the throttle and run the engine at 5,000 r/min or less.4. Continue operation at 5,000 r/min or less until the first tankful of fuel has been used.5. Fill the tank with straight gasoline, and then proceed with normal operation.@Failure to follow the engine break-in pro-cedure properly can result in severedamage to the engine.@CAUTION:3-15]]></page><page Index="77" isMAC="true"><![CDATA[EEJU01247Launching the watercraftMake sure that there are no obstructions behind you.After the watercraft is in the water, start the engine. Shift into reverse and move the watercraft back slowly. If there are waves, someone should make sure that the water- craft is not pushed into the trailer before backing away.EJU01248Starting the engine@Never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monox- ide, a colorless, odorless gas that may cause loss of consciousness and death within a short time. Always operate the watercraft in an open area.@1. Launch the watercraft in water free from weeds and debris and at least 60 cm (2 ft) deep.@Never operate in water that is less than 60 cm (2 ft) deep, otherwise you increase your chance of hitting a submerged object, which could result in injury.@@Never operate in water that is less than 60 cm (2 ft) deep, otherwise pebbles or sand could be sucked into the jet intake, causing impeller damage or engine over- heating.@WARNINGWARNINGCAUTION:3-16]]></page><page Index="78" isMAC="true"><![CDATA[E2. Turn the fuel cock knob to the “ON” posi- tion.Before starting the watercraft, after it has been sitting, remove the fuel tank filler cap to release any built-up pressure in the tank due to fuel expansion.@NOTE: @3. Attach the clip 1 to the engine shut-off switch 2. Also, attach the engine shut- off cord 3 to your left wrist.@Check that the engine shut-off cord is not frayed or broken, and keep it free from the handlebars so the engine stops if the operator falls off. The engine shut-off cord may not pull free if wrapped around the handlebars when the operator falls off, allowing the watercraft to continue to run and cause an accident.@It is not possible to start the engine with theclip removed from the engine shut-offswitch.@4. Pull and hold the choke knob all the way out to start a cold engine.The choke should not be used when the engine is warm.@WARNINGNOTE: @NOTE: @3-17]]></page><page Index="79" isMAC="true"><![CDATA[5. If the “LOCK” mode was chosen previ- ously, choose the “START” mode before starting the engine. (See pages 2-22 to 2-23 for selecting “PADLOC” mode.)NOTE: @qq@6.@IftheinitialsettingofthePADLOChasnot been done, the “START” mode is auto- matically selected.If you have previously chosen “LOCK” mode, the engine will not start unless the correct code is entered. This selects the “START” mode.While lightly squeezing the throttle lever, push the start switch (green button).EWARNINGOn this watercraft, the engine is con- nected directly to the jet pump. Starting the engine immediately generates some thrust. Apply only enough throttle to keep the engine running.@7. Release the start switch as soon as the engine starts to run.@q Never push the start switch while the engine is running.q Do not operate the start switch for more than 5seconds, otherwise the battery will be discharged and the engine will not start. Also, the starter motor may be damaged. If the engine does not start in 5 seconds, release the start switch, wait 15 seconds, and try again.@8. After the engine has warmed up, push the choke knob in to its original position.If the choke knob is left pulled out, the engine will stall.@CAUTION:NOTE: @3-18]]></page><page Index="80" isMAC="true"><![CDATA[EJU01066Stopping the engineTo stop the engine, release the throttle lever, and then push the engine stop switch (red button).@You need throttle to steer. Shutting off the engine can cause you to hit an obsta- cle you are attempting to avoid. A colli- sion could result in severe injury or death.@EJU01249Leaving the watercraftIf leaving the watercraft, choose the “LOCK” mode on the multifunction meter by setting PADLOC, and remove the engine shut-off cord to reduce the chance of acci- dental starting or unauthorized use by chil- dren or others.To set the mode, see PADLOC under Mul- tifunction meter.EWARNING3-19]]></page><page Index="81" isMAC="true"><![CDATA[EJU01068Operating your watercraftEJU01165Getting to know your watercraftOperating your watercraft requires skills acquired through practice over a period of time. Take the time to learn the basic tech- niques well before attempting more difficult maneuvers.Operating your new watercraft can be a very enjoyable activity, providing you with hours of pleasure. However, it is essential to familiarize yourself with the operation of the watercraft to achieve the skill level neces- sary to enjoy riding safely. Before operating this watercraft, read this Owner’s/Operator’s Manual, the Riding Practice Guide, the Riding Instruction card and all warning and caution labels on the watercraft. Pay particu- lar attention to the safety information on pages 1-8 to 1-15. Also, watch the Basic Orientation Video provided with your water- craft. These materials should give you an understanding of the watercraft and its oper- ation.Remember: This watercraft is designed to carry the operator and up to 2 passengers. Never exceed the maximum load limit or allow more than 3 persons (or 2 persons if a water-skier is being pulled) to ride the water- craft at one time.EJU01191Learning to operate your watercraftBefore operating the watercraft, always perform the pre-operation checks listed on page 3-5. The short time spent checking the watercraft will reward you with added safety and reliability.Check state and local laws before operat- ing your watercraft.Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft. Select a wide area to learn in, where you have good visi- bility and light boat traffic.Use the buddy system—operate with someone nearby. Scan constantly for peo- ple, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others.Attach the engine shut-off cord (lanyard) to your wrist and keep it free from the han- dlebars so that the engine stops if the opera- tor falls off.Wear a personal flotation device (PFD). All riders must wear a Coast Guard approved PFD that is suitable for personal watercraft use.EMaximum load: 240 kg (530 lb)Load is the total weight of cargo, opera- tor and passengers.3-20]]></page><page Index="82" isMAC="true"><![CDATA[EWear protective clothing. Severe internal injuries can occur if water is forced into body cavities as result of falling into the water or being near the jet thrust nozzle. Normal swimwear does not adequately protect against forceful water entry into rectum and vagina. All riders must wear a wetsuit bot- tom or clothing that provides equivalent pro- tection.Such clothing includes thick, tightly woven, sturdy and snug-fitting apparel such as denim, but does not include spandex or similar fabrics like those used in bicycle shorts. A full wetsuit can also protect against hypothermia (subnormal body temperature) and abrasions.Footwear and gloves are recommended.Eye protection is recommended to keep wind, water, and glare from the sun out of your eyes while you operate your watercraft. Restraining straps for eyewear are made which are designed to float should your eye- wear fall in the water.You should grip the handlebars firmly and keep both feet on the floor of the footwell. Do not attempt to ride with passengers until your operating skills are fully developed.EJU01166Riding watercraft withpassengersWhen 2 or 3 persons (including the oper- ator) are on board, the watercraft handles differently, and is not as easy to maneuver, so operating it requires a higher degree of skill. Before attempting to operate the water- craft with passengers on board, the operator must practice operating the watercraft alone enough to be able to acquire the necessary skills.The passengers must always wear USCG approved PFD and wetsuit bottom or equiv- alent.@Do not apply throttle when anyone is at rear of watercraft. Turn engine off or keep engine at idle. Water and/or debris exit- ing the jet thrust nozzle can cause severe injury. Passengers should not attempt to board the watercraft if the operator is applying throttle.@Do not give a ride to children whose feet cannot reach the floor of the footwell. Pas- sengers should hold on firmly to the person in front of them and keep both feet in the footwell.@When passengers are on board, make sure that they are holding on firmly and have feet in the footwell before you start to accelerate.@When pulling a skier, the spotter should face to the rear while holding the handgrip with both hands. The spotter should always sit astride the seat with his or her feet placed firmly on the footrest for proper balance. Fol- low state laws regarding skiing such as skier-down flags, rearward-facing spotter, and other requirements.WARNINGWARNING3-21]]></page><page Index="83" isMAC="true"><![CDATA[EJU01072Starting the watercraft@q Scan constantly for people, objects and other watercraft. Be alert for con- ditions that limit your visibility or block your vision of others.q Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft.q Do not follow directly behind water- craft or other boats. Do not go near others to spray or splash them with water. Avoid sharp turns or other maneuvers that make it hard for others to avoid you or understand where you are going. Avoid areas with sub- merged objects or shallow water.q Take early action to avoid collisions. Remember watercraft and other boats do not have brakes. Do not release the throttle when trying to steer away from objects—you need throttle to steer.q Practice reboarding in shallow water before riding in deep water.@EWARNING3-22]]></page><page Index="84" isMAC="true"><![CDATA[E3-23EJU01073Starting and boarding in shallow water1. Do not start the engine in less than60 cm (2 ft) of water. Put the watercraft in water that is deep enough, and then board the watercraft from the side or the rear.2. Attach the engine shut-off cord to your left wrist, and then install the clip to the engine shut-off switch.3. Grip the handlebars with both hands, place both feet on the floor of the foot- well, start the engine, and start off.EJU01074Starting from a dock1. Board the watercraft from the side.2. Attach the engine shut-off cord to your left wrist, and then install the clip to theengine shut-off switch.3. Push the watercraft away from the dock,grip the handlebars with both hands, place both feet on the floor of the foot- well, start the engine, and start off.]]></page><page Index="85" isMAC="true"><![CDATA[EEJU01075Boarding and starting in deep water@q Operator and passenger should prac- tice getting on board in shallow water before riding in deep water. Boarding in deep water requires more skill.q The fatigue and exposure that could result after unsuccessful attempts to get back on the watercraft may increase the risk of injuries and drown- ing.@EJU01076Boarding alone1. Swim to the rear of the watercraft and place both hands on the boarding plat- form, pull yourself up, and then grasp the handgrip with one hand.2. Pull yourself up to a kneeling position on the platform, and then move to the seat and sit astride.3. Attach the engine shut-off cord to your wrist, and then install the clip to the engine shut-off switch.4. Grip the handlebars firmly with both hands, place both feet in footwell, start the engine, and look in all directions before starting off.@Before starting off, make sure that thereare no boats, obstructions, or swimmersaround you.@WARNINGWARNING3-24]]></page><page Index="86" isMAC="true"><![CDATA[EEJU01252Boarding with passengers@Severe internal injuries can occur if water is forced into body cavities as a result of being near the jet thrust nozzle. Do not apply throttle until each passen- ger is seated with his or her feet on the floor of the footwell and is holding on to the person in front of him or her.@1. Climb on board as noted in the previous section, and sit astride the seat. Attach the engine shut-off cord to your wrist, and then install the clip to the engine shut-off switch.2. Have the passenger move to the rear of the watercraft.3. Have the passenger get on board and sit on the seat. If a second passenger is getting on, have him or her follow the same procedure.When a passenger is getting on board, bothhe and the operator should try to balancethe watercraft.@4. The operator should check to see that the passengers have their feet on the floor of the footwell and that they are securely holding on to the person in front of them.5. Start the engine, look in all directions, and then accelerate to planing speed.@Before starting off, make sure that thereare no boats, obstructions, or swimmersaround you.@WARNINGNOTE: @WARNING3-25]]></page><page Index="87" isMAC="true"><![CDATA[NOTE: @The heavier the total weight of the operator and passengers, the more difficult it will be to balance the watercraft. Do not operate the watercraft when the total weight exceeds 240 kg (530 lb) including any cargo. If it is difficult to balance the watercraft at a stand- still, proceed as follows:1. The passenger must steady the water- craft while the operator is boarding. The operator pulls himself up onto the plat- form into a seating position, then bal- ances the watercraft.2. Attach the lanyard to your left wrist, then install the clip on the lanyard to the engine shut-off switch. Start the engine and keep it at idle.3. The passenger pulls himself up on the platform kneels down, then crawls onto the seat as the watercraft accelerates.4. The watercraft can now be accelerated to planing speed, then the operator can reduce the throttle to the desired running speed.@EJU01078Capsized watercraftIf the watercraft capsizes, follow the pro- cedures below carefully to prevent damage or injury.@IMPROPER UPRIGHTING CAN CAUSE INJURY:q Shut engine off, and be sure engineshut-off cord is removed from theengine shut-off switch.q Donotputhandinintakegrate.q Watch so you are not hit by the water-craft as it comes over.@EWARNING3-26]]></page><page Index="88" isMAC="true"><![CDATA[@Be sure to remove the clip from the engine shut-off switch, otherwise the engine will overheat and engine damage may occur.@1. Shut the engine off by removing the clip from the engine shut-off switch.2. Swim to the rear of the watercraft. Pull the watercraft over with left hand on ride plate while pushing down on the gun- wale with your right hand/foot.If the port side of the capsized watercraftis tilting upward, first tilt the watercraft so theport side is down by using your weight topress down on the gunwale.@@Do not turn the watercraft over counter- clockwise, otherwise water may leak into the carburetor and engine and cause damage.@3. Start the engine, and then head for shore to inspect the engine for water damage.@If the watercraft has been capsized for 5 minutes or more, air may have entered the oil injection system. Leave the engine off, or operate only at trolling speed, for 10 minutes after the watercraft has been turned right-side up. This will allow any air to bleed off.ECAUTION:NOTE: @CAUTION:CAUTION:3-27]]></page><page Index="89" isMAC="true"><![CDATA[EJU01079Turning the watercraftSteering control depends on the combi- nation of handlebar position and the amount of throttle.Water sucked in through the intake grate is pressurized by the impeller in the jet pump. As the pressurized water is expelled from the pump through the jet thrust nozzle, it creates thrust to move and steer the watercraft. The higher the engine speed, the more thrust is produced.The amount of jet thrust, in addition to the position of the handlebars, determines how sharply you turn.A. More throttle produces higher thrust, sothe watercraft will turn more sharply.B. Less throttle produces lower thrust, sothe watercraft will turn more gradually.C. Releasing the throttle completely pro- duces only minimum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to steer without throttle. You may still have some turning ability immediately after releasing the throttle, but once the engine slows down, the watercraft will no longer respond to handlebar input until you apply throttle again or you reach atrolling speed.At trolling speed, the watercraft can be turned gradually by handlebar position alone using just the amount of thrust available at idle.D. If the engine is stopped while riding, there is no thrust. The watercraft will go straight even though the handlebars are turned.You need throttle to steer.E3-28]]></page><page Index="90" isMAC="true"><![CDATA[EWARNING@q Do not release the throttle when trying to steer away from objects—you need throttle to steer. A collision could result in severe injury or death.q When operating at higher speeds, make gradual turns or slow down before turning. Sharp high-speed turns may cause the watercraft to slide side- ways or spin, throwing the operator and passengers overboard which could cause an injury.@3-29]]></page><page Index="91" isMAC="true"><![CDATA[EEJU01253Stopping the watercraftThe watercraft is not equipped with a sep- arate braking system. It is stopped by water resistance when the throttle lever is released. From full speed, the watercraft comes to a complete stop in approximately 110 m (360 ft) after the throttle is released and the engine is stopped, although this dis- tance will vary depending on many factors, including gross weight, water surface condi- tions, and wind direction. The watercraft slows down as soon as the throttle lever is released, but will coast for a distance before fully stopping. If you are not sure you can stop in time before hitting an obstacle, apply throttle and turn in another direction.@q Allowadequatestoppingdistance.q Take early action to avoid collisions. Remember, watercraft and other boatsdo not have brakes.q Operate defensively at safe speedsand keep a safe distance away from people, objects, and other watercraft to give you time to stop.q Do not shut the engine off when slow- ing down in case you need engine power to steer away from a boat or other obstacle that comes into your path.@@Do not use the reverse function to slow down or stop the watercraft as it could cause you to lose control, be ejected, or impact the handlebars.@WARNINGWARNING3-30]]></page><page Index="92" isMAC="true"><![CDATA[EEJU01081Beaching the watercraft1. Make sure no obstructions, boats or swimmers are near the beach. Release the throttle lever about 110 m (360 ft) before you reach the intended beaching area.2. Approach the beach slowly and stop the engine before reaching land. Remember: you need throttle to steer.3. Get off the watercraft and pull it up on the beach.@Small pebbles, sand, seaweed, and other debris can be pulled into the jet intake and impair or damage the impeller. Always stop the engine and get off before beaching the watercraft.@EJU01082Docking the watercraft1. Make sure that no obstructions, boats or swimmers are close to the watercraft. Reduce speed about 110 m (360 ft) away from the dock.2. Slowly approach the dock and stop the engine just before coming alongside it.CAUTION:3-31]]></page><page Index="93" isMAC="true"><![CDATA[EEJU01254Reverse on waterwaysReverse can be used for slow speed maneuvering when it is necessary to back up out of tight spots where you cannot turn around. Reverse can only be used to slow down or stop during low speed maneuver- ing, such as when docking.Once the engine is idling, shift to reverse and gradually increase engine speed. Make sure that there are no obstacles or people behind you before shifting to reverse.EJU01255Rough water operationThe force of landing after jumping can cause a strong impact on both the watercraft and the operator and passengers. It is pos- sible for the operator to hit his or her chest or jaw on the watercraft body or handlebars and be injured. Do not operate the water- craft with your chin right above the handle- bars or with your feet outside the watercraft. Operating in rough water or jumping waves can also crack the watercraft body or dam- age internal parts. Avoid operating in rough water or bad weather conditions.3-32]]></page><page Index="94" isMAC="true"><![CDATA[EEJU01193Post-operation checksAlways perform the following post-opera- tion checks after operating the watercraft.@Stay away from stern when engine is run- ning on land. Hot water and steam spurt- ing from exhaust outlet into the air can cause serious burns.@1. Remove the watercraft from the water.2. Wash down the hull, handlebars, and jetunit with fresh water.3. Remove the seat and check the enginecompartment for water. To drain excess water, remove the stern drain plugs, then raise the bow of the watercraft enough to allow water in the bilge to drain out.This watercraft is equipped with an auto- matic bilge-draining system that removes water from the engine compartment while you are underway. However, some residual water will remain.@4. Put the watercraft in a horizontal posi- tion.5. Flush the cooling system to prevent it from clogging with salt, sand, or dirt. (See page 4-1 for flushing the cooling system procedures.)6. Drain residual water from the exhaust sys- tem by running the engine at 4,000 r/min for 10 to 15 seconds.@Do not run engine over 4,000 r/min onland. Otherwise catalytic converter couldsustain serious damage.@WARNINGNOTE: @CAUTION:3-33]]></page><page Index="95" isMAC="true"><![CDATA[E7. If the watercraft will be stored for a week or more, lubricate internal engine com- ponents to help prevent corrosion. (See page 4-3 for lubrication procedures.)8. Rinse the engine and engine compart- ment with a small amount of water.@Do not use high pressure when rinsingthe engine or engine compartment assevere engine damage could result.@9. Wipe the engine and engine compart- ment dry with a clean cloth (repeat step 3, if necessary).10.Wipe the hull, handlebars, and jet unit dry with a clean cloth.11.Spray a rust inhibitor, such as Yamaha Silicone Protectant and Lubricant, on metallic parts to minimize corrosion.@Do not spray flammable rust inhibitor products on engine surfaces while the engine is hot. The sprayed substance or propellants could catch fire.@12. Allow the engine compartment to air dry completely before reinstalling the seat.Cover watercraft after engine and catalytic converter cool down.@CAUTION:WARNINGNOTE: @3-34]]></page><page Index="96" isMAC="true"><![CDATA[EEJU01256@TransportingWARNINGAlways place the fuel cock knob in the “OFF” position when transporting the watercraft, otherwise fuel could leak out into the engine or engine compartment, which would create a fire hazard.@When transporting the watercraft on a trailer, secure the tie downs to the trailer through the bow eye and stern rope hole.@q Do not route ropes or tie downs over the seat, as they may leave permanent marks on the seat’s surface. Also, wrap the ropes or tie downs with tow- els or rags where they touch the body of the watercraft to avoid scratching or damage.q Before putting the watercraft on the trailer or transporting it, be sure to put the shift lever in the forward position, otherwise the reverse gate may hit an obstruction, which may cause dam- age.@CAUTION:3-35]]></page><page Index="97" isMAC="true"><![CDATA[EJU01086MAINTENANCE AND CAREStorage ......................................................4-1 Flushing the cooling system ..................4-1 Lubrication ..............................................4-3 Fuel system ............................................4-4 Battery ....................................................4-5 Cleaning the watercraft ..........................4-6Maintenance and adjustments ..............4-7 Owner’s/Operator’s Manual andtool kit .....................................................4-8 Periodic maintenance chart....................4-9 Inspecting the fuel system ...................4-10 Inspecting the oil injection system .......4-12 Inspecting the steering cable ...............4-13 Inspecting the shift cable .....................4-13 Inspecting and adjusting thethrottle cable .........................................4-13 Inspecting the QSTS mechanism .......4-14 Cleaning and adjusting thespark plugs ...........................................4-15 4 Lubrication points .................................4-16 Adjusting the choke cable ....................4-19 Inspecting the battery ..........................4-20 Adjusting the carburetor ......................4-22 Replacing the fuse ...............................4-23 Bleeding the oil injection pump ............4-23Specifications ........................................4-24E]]></page><page Index="98" isMAC="true"><![CDATA[EEJU01087@StorageWARNINGAlways place the fuel cock knob in the “OFF” position when storing the water- craft, otherwise fuel could leak out into the engine or engine compartment, which would create a fire hazard.@Storage for prolonged periods of time, such as winter storage, requires preventa- tive maintenance to ensure against deterio- ration. It is advisable to have the watercraft serviced by a Yamaha dealer prior to stor- age. However, the following procedures can be performed by the owner.EJU01194Flushing the cooling systemFlushing the cooling system is essential to prevent the cooling system from being clogged with salt, sand, or dirt.@Stay away from stern when engine is run- ning on land. Hot water and steam spurt- ing from exhaust outlet into the air can cause serious burns.@@q Do not supply water to the cooling water passages when the engine is not running. The water could flow back through the muffler into the crankcase causing severe engine damage.q Do not run the engine for more 15seconds without supplying water, otherwise the engine may overheat.q Do not run engine over 4,000 r/min on land. The catalytic converter could sustain serious damage.@WARNINGCAUTION:4-1]]></page><page Index="99" isMAC="true"><![CDATA[E1. Put the watercraft on land in a horizontal position.2. Open the flushing hose connector cap 1, and then insert the garden hose adapter 2 into the flushing hose connector 3 and turn it until it is securely connected.3. Connect the garden hose adapter to a water tap using a hose.4. Start the engine, and then immediately turn the water supply on until water flows out continually from the cooling water pilot outlet.5. Run the engine at idling speed for about 3 minutes watching the engine condition. If the engine stops while flushing, turn the water supply off immediately and repeat the above steps.6. Turn the water supply off, and then force the remaining water out from the cooling passages by running the engine at4,000 r/min or less within 10 to 15 seconds.7. Stop the engine.8. Remove the garden hose adapter andsecure the cap.4-2]]></page><page Index="100" isMAC="true"><![CDATA[EJU01195Lubrication@Do not spray flammable rust inhibitor products on engine surfaces while the engine is hot. The sprayed substance or propellants could catch fire.@1. Remove the spark plugs and pour approximately one tablespoon of oil into each cylinder.2. Grease the spark plug threads and rein- stall the spark plugs.3. Crank the engine within 3 seconds using the start switch.4. Lubricate all cables such as the throttle, choke, and steering cables.Use a Yamaha Power Cable Luber and Yamaha Lube-Zall to pressure lubricate the cables and purge out any moisture between the inner and outer cables.@5. Lubricate the areas of the watercraft speci- fied under Lubrication points on page 4-16.EWARNINGNOTE: @4-3]]></page><page Index="101" isMAC="true"><![CDATA[EEJU01091Fuel systemDraining the fuel system prevents buildup of varnishes and other harmful deposits that result when gasoline sits for a prolonged period of time.@Gasoline is highly flammable and explo- sive. A fire or explosion can cause severe injury or death. Shut the engine off. Drain in well-ventilated areas away from flames or sparks. Do not smoke. Avoid spilling gaso- line. Wipe up spilled gasoline immediately.@To drain the fuel system:1. Place the fuel cock knob in the “OFF” position.2. Drain the fuel tank using a siphon.WARNING4-4]]></page><page Index="102" isMAC="true"><![CDATA[EEJU01092BatteryIf the watercraft is not used for a month or more, disconnect the (–) battery cable first, and then the (+) cable and breather pipe, and next remove the battery from the craft.Clean the battery casing using fresh water.If the battery terminals are dirty or cor- roded, clean the mating surfaces on the ter- minals for the battery cables using the wiring brush or equivalents.Recharge the battery, and then store it in a cool and dark place.Apply the Yamaha marine grease/Yamaha grease A to the battery terminals.Recharge the battery periodically at least 2 months because a battery will discharge electricity by itself while storing.@The battery may be impossible to use again if you store it for a longer time without recharging. Recharge the battery periodically.@The battery condition can be found by checking the specific gravity of the electro- lyte. However, you can also know the battery condition roughly by measuring the voltage at both battery terminals. Recharge the bat- tery if the voltage is 12 volts or less.Yamaha recommend checking the specific gravity of the electrolyte and charging bat- tery by a Yamaha dealer or a battery dealer. If you maintain the battery yourself, read carefully the instructions for the tool and machine before maintenance.@CAUTION:NOTE: @Specific gravity of electrolyte (for reference):1.28 at 20 °C (68 °F)4-5]]></page><page Index="103" isMAC="true"><![CDATA[EEJU01196Cleaning the watercraftClean the watercraft before storing it for a long period.@Do not spray flammable rust inhibitor products on engine surfaces while the engine is hot. The sprayed substance or propellants could catch fire.@1. Wash down the hull, handlebars, and drive unit with fresh water.2. Rinse the engine and bilge area with fresh water. Drain off all water and wipe up remaining moisture with clean, dry rags.3. Spray the engine’s exterior with Yamaha Silicone Protectant and Lubricant.4. Wax the hull with a non-abrasive wax such as Yamaha Silicone Wax.5. Wipe all vinyl and rubber components, such as the seat and engine compart- ment seals, with a vinyl protectant such as Yamaha Protectant.WARNING4-6]]></page><page Index="104" isMAC="true"><![CDATA[Periodic inspection, adjustment and lubri- cation will keep your watercraft in the safest and most efficient condition possible. Safety is an obligation of the watercraft owner. The most important points of watercraft inspec- tion, adjustment and lubrication are explained on the following pages.See your Yamaha dealer for genuine Yamaha replacement parts and optional accessories designed for your watercraft.Remember that failures that are the result of the installation of parts or accessories which are not qualitatively equivalent to gen- uine Yamaha parts are not covered by the limited warranty.Maintenance, replacement, or repair of the emission control devices and system may be performed by any marine engine repair establishment or individual. War- ranty repair (emission or normal) how- ever, must be performed at an authorized Yamaha marine dealership.@q Besuretoturnofftheenginewhenyou perform maintenance unless other- wise specified, otherwise an accident or injury could result from unexpected operation, moving parts, or electric shock. If the owner is not familiar with watercraft servicing, this work should be done by a Yamaha dealer. Improp- erly serviced components could fail or stop operating correctly, which could result in an accident.q Modifications to this watercraft not approved by Yamaha may cause loss of performance or excessive noise, or ren- der it unsafe for use. Consult a Yamaha dealer before attempting any changes.@EEJU01197Maintenance and adjustmentsWARNING4-7]]></page><page Index="105" isMAC="true"><![CDATA[ENOTE: @A service manual is available for purchase through a Yamaha dealer for owners who have the mechanical skills, tools, and other equipment necessary to perform mainte- nance not covered by this Owner’s/Opera- tor’s Manual.@EJU01198Owner’s/Operator’s Manual and tool kitIt is advisable always to carry the Owner’s/Operator’s Manual and tool kit 2 with you whenever you use the watercraft. For your convenience, a storage compart- ment 1 is provided on the watercraft for the manual and tool kit.To protect these materials from water dam- age, it would be a good idea to put them in a waterproof bag. If your Owner’s/Operator’s Manual is damaged, order a replacement from a Yamaha dealer.@The service information included in this manual is intended to provide you with the necessary information for completing your own preventive maintenance and minor repairs. The tools provided in the tool kit are sufficient for this purpose. However, a torque wrench may also be necessary to tighten nuts and bolts.NOTE: @4-8]]></page><page Index="106" isMAC="true"><![CDATA[EEJU01357Periodic maintenance chartThe following chart gives general guidelines for periodic maintenance. However, depend- ing on your operating conditions maintenance may need to be performed more frequently.(q) This mark indicates maintenance that you may do yourself. (❍) This mark indicates work to be done by a Yamaha dealer.ITEMMAINTENANCE INTERVALINITIALTHEREAFTER EVERYPAGE10 hours50 hours100 hours100 hours200 hours3 months6 months6 months12 monthsSpark plugInspect, clean, adjustqqqq4-15Lubrication pointsLubricateqq4-16Intermediate housingLubricate❍*1q*2q*24-19Fuel systemInspect❍❍4-10Fuel filterCheck, replace❍❍4-11Fuel tankClean❍4-11Oil injection systemInspect, clean❍❍4-12Trolling speedAdjustqq4-22Carburetor throttle shaftInspect❍❍—Cooling water passagesFlushq (after every use)4-1Bilge strainerCleanqqq—ImpellerInspectqqq—Steering cableInspectqq4-13Steering masterInspect❍❍❍—QSTS mechanismInspectqq4-14Shift cable and mechanismInspect, adjustqq4-13Throttle cableInspect, adjustqq4-13Choke cableInspect, adjustqq4-19Stern drain plugsInspect, replaceq3-7BatteryInspectq(inspect fluid level before every use)4-20Rubber couplingInspect❍—Nuts and boltsRetighten❍❍❍—*1: Grease capacity: 33.0–35.0 cm3 (1.11–1.18 oz) *2: Grease capacity: 6.0–8.0 cm3 (0.20–0.27 oz)4-9]]></page><page Index="107" isMAC="true"><![CDATA[EJU01199Inspecting the fuel system@Gasoline is highly flammable and explo- sive. A fire or explosion can cause severe injury or death. Shut off the engine. Do not smoke. Avoid spilling gasoline. Do not drain the fuel while the engine is hot.@Check the fuel system for leaks, cracks, or malfunctions. If any problem is found, do the necessary repair or replacement as required. If repair is necessary, consult a Yamaha dealer.Check:q Carburetorforleakage.q Fuelpumpformalfunctionorleakage.q Fueltankforwaterordirt.q Fueltankfordamage,cracksorleakage. q Fuelhosejointforleakage.q Fuelhoseforcracksorotherdamage.q Fuelfilterforleakage.q Fuelcockforleakage.q Airventcheckvalveforleakage.q Fueltankfillercapfordamage.@Failure to check for and repair any fuel leakage may result in fire or explosion.@EWARNINGWARNING4-10]]></page><page Index="108" isMAC="true"><![CDATA[EEJU01098Fuel filterThis watercraft is equipped with a one- piece, disposable fuel filter 1. The fuel filter should be replaced once a year or after every 200 hours of operation, or if water is found in the filter. Have a Yamaha dealer replace the fuel filter if necessary.@Do not try to replace the fuel filter your- self. An incorrectly installed filter can leak gasoline, which could lead to fire or explosion. If necessary, have a Yamaha dealer replace the fuel filter.@EJU01099Fuel tankCheck the fuel tank 1 for leakage or water in the tank. If water is found in the fuel system or if the fuel tank needs to be cleaned have a Yamaha dealer service the watercraft.WARNING4-11]]></page><page Index="109" isMAC="true"><![CDATA[EEJU01100Inspecting the oil injection systemCheck the oil injection system for leakage, cracks, or malfunctions. If necessary, have a Yamaha dealer repair the oil injection sys- tem.Check:q Oiltankfordamage,cracksorleakage. q Oiltankforwaterordirt.q Oilhoseandjointfordamageorcracks. q Oilfilterfordirt.q Oilpumpforleakage.EJU01101Oil tankCheck the oil tank for leakage or water in the tank. If water is found in the oil injection system or if the oil tank needs to be cleaned have a Yamaha dealer service the water- craft.EJU01102Oil filterCheck the oil filter 1 for dirt and clogs. If the oil filter is clogged, remove it from the oil tank together with the oil level sender and clean it.4-12]]></page><page Index="110" isMAC="true"><![CDATA[E4-13EJU01258Inspecting the steering cableCheck for smooth operation of the handle- bars and jet thrust nozzle.Turn the handlebars as far as possible to the right and left and check that the distance between the jet thrust nozzle and the bracket of the reverse gate are equal on right and left sides.If steering is stiff or misadjusted, have a Yamaha dealer service it.EJU01259Inspecting the shift cablePlace the shift lever in the reverse posi- tion.Make sure the gate makes contact with the stopper 1 on the bracket, and the arm 2 makes contact with the reverse gate.If the reverse gate does not reach the cor- rect positions, have a Yamaha dealer ser- vice it.EJU01104Inspecting and adjusting thethrottle cableCheck that the throttle cable moves back to the set position smoothly and that free play is within specification.1. Squeeze and release the throttle lever. Ifthe lever does not return smoothly, havea Yamaha dealer service it.2. Adjust free play a by loosening the lock-nut 1 and turning the adjuster 2.Distance A and B: A=BThrottle lever free play: 4–7 mm (0.16–0.28 in)]]></page><page Index="111" isMAC="true"><![CDATA[EEJU01105Inspecting the QSTS mechanismCheck that the shift lock lever moves back to the lock position smoothly, that the QSTS selector locks and unlocks properly, and that the jet thrust nozzle moves up or down.1. Squeeze and release the shift lock lever.2. Check that the QSTS selector lockswhen the lever is released.3. Check that the selector turns smoothlywhen the lever is squeezed and held inplace.4. Check that the angle of the jet thrustnozzle changes when the selector is shifted from neutral to bow-up or bow- down.If the mechanism does not work properly,have a Yamaha dealer service it.4-14]]></page><page Index="112" isMAC="true"><![CDATA[E4-15EJU01106Cleaning and adjusting the spark plugsThe spark plug is an important engine component and is easy to inspect. The con- dition of the spark plug can indicate some- thing about the condition of the engine. For example, if the center electrode porcelain is very white, this could indicate an intake air leak or carburetion problem in that cylinder. Do not attempt to diagnose any problems yourself. Have a Yamaha dealer service the watercraft.Remove and inspect the spark plug peri- odically; heat and deposits will cause the spark plug to slowly break down and erode. If electrode erosion becomes excessive, or if carbon and other deposits are excessive, replace the spark plug with the specified plug.Measure the spark plug gap a with a wire thickness gauge before installing the spark plug. Adjust the gap to specification if necessary.To reinstall spark plug:1. Clean the gasket surface.2. Wipe any dirt from the threads of thespark plug.3. Screw the spark plug to the correcttorque.Standard spark plug: BR8ES-11Spark plug gap:1.0–1.1 mm (0.039–0.043 in)Spark plug torque:25 N·m (2.5 kgf·m, 18 ft·lb)]]></page><page Index="113" isMAC="true"><![CDATA[ENOTE: @q Wipe off any water on the spark plug or inside the cap before installing the spark plug cap. Push the spark plug cap down until it clicks.q If a torque wrench is not available when you are fitting a new spark plug, a good estimate of the correct torque is 1/4 turn to 1/2 turn past finger tight. Have the spark plug adjusted to the correct torque with a torque wrench as soon as possible.@@Be careful not to damage the insulator when removing or installing a spark plug. A damaged insulator could allow sparks to escape, which could lead to explosion or fire.@EJU01339Lubrication pointsTo keep moving parts sliding or rotating smoothly, coat them with water-resistant grease.q Throttlecable(carburetorend) q OilpumpcableWARNING4-16Recommended water-resistant grease: Yamaha Marine Grease/Yamaha Grease A]]></page><page Index="114" isMAC="true"><![CDATA[Eq Throttlecable(handlebarend)Squeeze the throttle lever and remove theseal 1. Spray a rust inhibitor into the outer cable. Refit the seal securely.q Steeringcable(handlebarend)q Steeringcable(nozzleend) q Nozzlepivotshaftq QSTScable(nozzleend)q QSTScables(pulleyend)F0D41004-17]]></page><page Index="115" isMAC="true"><![CDATA[Eq QSTScables(handlebarend)Remove the QSTS cable housing. Spraya rust inhibitor into the outer cable. Reinstall the QSTS cable housing.q Shiftcable(leverend)4-18q Shiftcable(reversegateend)q YPVScable]]></page><page Index="116" isMAC="true"><![CDATA[q IntermediatehousingUsing a grease gun, fill the intermediatehousing with water-resistant grease through the grease nipple 1.EJU01261Adjusting the choke cableCheck that the choke cable is properly adjusted.1. Pull the choke knob out until it stops, and then release the knob. The knob should not move.2. If the choke knob moves back on its own, tighten the choke knob adjusting nut 1 slightly. If the knob is difficult to move, loosen the adjusting nut slightly.EGrease capacity:Initial 10 hours or 1 month:33.0–35.0 cm3 (1.11–1.18 oz) Every 100 hours or 6 months:6.0–8.0 cm3 (0.20–0.27 oz)4-19]]></page><page Index="117" isMAC="true"><![CDATA[EEJU01108Inspecting the batteryCheck the level of the battery electrolyte and make sure the leads are secure.@Battery electrolyte is poisonous and dan- gerous, causing severe burns, etc. Elec- trolyte contains sulfuric acid. Avoid contact with skin, eyes or clothing. AntidotesExternal: Flush with water.Internal: Drink large quantities of wateror milk. Follow with milk of magnesia,beaten egg or vegetable oil. Call physi-cian immediately.Eyes: Flush with water for 15minutesand get prompt medical attention.Batteries produce explosive gases. Keepsparks, flame, cigarettes, etc., well away.If using or charging the battery in anenclosed space, make sure that it is wellventilated. Always shield your eyes whenworking near batteries.KEEP OUT OF THE REACH OF CHILDREN.@@Be careful not to place the battery on its side.Make sure to remove the battery from the battery compartment when adding bat- tery electrolyte or charging the battery. When checking the battery, make sure the breather hose is connected to the battery and not obstructed.@WARNINGCAUTION:4-20]]></page><page Index="118" isMAC="true"><![CDATA[ETo replenish the battery:1. Make sure that the electrolyte level is between the upper 1 and lower 2 level marks.2. Refill the battery with distilled water if necessary.@Normal tap water contains minerals thatare harmful to a battery. Use only dis-tilled water for replenishing the battery.@To recharge the battery:@Do not attempt to charge a battery hast- ily. Battery life may be shorter.@Yamaha recommend charging battery by a Yamaha dealer or a battery dealer. If you charge the battery yourself, read the battery charger instructions carefully before charg- ing and follow the points below.1. Remove all caps from the battery cell.2. Add distilled water to the specified level ifthe electrolyte level is low.3. Set the charging rate to 1.9 ampere andcharge the battery slowly until the explo- sive gases become coming out vigor- ously from battery cells.To connect the battery terminals:1. Make sure that the connections are correct when you insert the battery in the watercraft.2. Make sure that the breather hose isproperly connected and that it is notdamaged or obstructed.3. Make sure that the battery is securelyheld in place.1 Positive (+): Red lead 2 Negative (–): Black lead 3 Breather hoseCAUTION:CAUTION:4-21]]></page><page Index="119" isMAC="true"><![CDATA[EEJU01109Adjusting the carburetorThe carburetor is a vital part of the engine and requires very sophisticated adjustment. Most adjusting should be left to a Yamaha dealer who has the professional knowledge and experience to perform it. However, the operator may adjust the trolling speed as part of the usual maintenance routine.@The carburetor was set at the Yamaha factory after many tests. If the settings are disturbed by someone who does not have the necessary technical knowledge, poor engine performance and damage may result.@EJU01345Adjusting the trolling speed1. Put the watercraft in the water.2. Start the engine and warm it up for 1 or 2 minutes. Using a diagnostic tachome- ter or, if necessary, the tachometer in the multifunction meter, adjust the enginespeed to specification.3. Turn the throttle stop screw 1 clockwiseto increase engine speed if necessary. Turn it counterclockwise to decrease engine speed if necessary.CAUTION:4-22Trolling speed: 1,300–1,400 r/min]]></page><page Index="120" isMAC="true"><![CDATA[EJU01702Replacing the fuseThe fuses are in the electrical box 1. To replace the fuse:1. Remove the hose band a and keep theduct hose b away from the electricalbox.2. Remove the cap 2 on the electrical box.3. Remove the fuse using the fuse puller 3.4. Replace the fuse with one of the correctamperage.Do not use fuses of higher amperage that those recommended. Substitution of a fuse of improper rating can cause exten- sive electrical system damage and possi- ble fire.EJU01112Bleeding the oil injection pumpIf the oil tank becomes completely empty, or any hose connected to the oil pump has been disconnected, the oil pump must be bled to ensure proper oil flow.If bleeding of the oil pump is necessary, have a Yamaha dealer bleed it.EFuse amperage: 10 A, 20 AWARNING4-23]]></page><page Index="121" isMAC="true"><![CDATA[EEJU01364SpecificationsITEMMODELUnitXLT1200WATERCRAFT CAPACITYMaximum people on board Maximum load capacityNumber of people kg (lb)3240 (530)DIMENSIONSLength Width Height Dry weightmm (in) mm (in) mm (in) kg (lb)3,160 (125) 1,220 (48) 1,130 (45) 361 (796)PERFORMANCEMaximum outputMaximum fuel consumption Cruising range at full throttle Trolling speedkW (PS) @ r/min L/h (US gal/h, Imp gal/h) hr.r/min114 (155)@ 7,000 64 (17, 14)1.091,300–1,400ENGINEEngine typeNumber of cylinders Engine displacement Bore & stroke Compression ratio Lubrication system Cooling system Starting system Ignition system Spark plugSpark plug gap Battery capacity Charging systemcm3 (cu in) mm (in)mm (in) V-AH2-stroke31,176 (71.8)80.0 × 78.0 (3.15 × 3.07) 5.9:1Variable oil injection Water cooledElectric starterDigital CDIBR8ES-11 (NGK) 1.0–1.1 (0.039–0.043) 12-19Flywheel magnetoDRIVE UNITPropulsion system Jet pump type Impeller rotation TransmissionJet thrust nozzle horizontal angle Jet thrust nozzle trim angleDegree DegreeJet pumpAxial flow, single stage Counterclockwise (viewed from rear) Direct drive from engine24 + 24-7, -2, 3, 8, 13FUEL AND OILRecommended fuel Minimum octane ratingRecommended engine oil Fuel tank capacityTotalReserveOil tank capacityPON RONL (US gal, Imp gal) L (US gal, Imp gal) L (US gal, Imp gal)Regular unleaded gasoline 8690YAMALUBE 2-W only70 (18.5, 15.5) 12 (3.2, 2.7) 5.5 (1.5, 1.3)4-24]]></page><page Index="122" isMAC="true"><![CDATA[E–MEMO–]]></page><page Index="123" isMAC="true"><![CDATA[EJU01115TROUBLESHOOTING AND EMERGENCY PROCEDURESTroubleshooting ......................................5-1 Troubleshooting chart ............................5-1 Emergency procedures ..........................5-4 Cleaning the jet intake and impeller ......5-4 Jumping the battery ...............................5-5 Towing the watercraft ............................5-7 Submerged watercraft ...........................5-8E5]]></page><page Index="124" isMAC="true"><![CDATA[EJU01116TroubleshootingIf you have any trouble with your watercraft, use this section to check for the possible cause.If you cannot find the cause, or if the procedure for replacement or repair is not described in this Owner’s/Operator’s Manual, have a Yamaha dealer perform the necessary service.EJU01372Troubleshooting chartETROUBLEPOSSIBLE CAUSEREMEDYPAGEEngine does not startStarter motor does not turn overMultifunction meter“LOCK” mode selectedSelect “START” mode2-22Engine shut- off switchClip not in placeInstall clip2-10FuseBurned outReplace the fuse and check wiring4-23BatteryRun downRecharge4-21Poor terminal connec- tionsTighten as required4-21Terminal corrodedClean4-5Starter motorFaultyHave serviced by Yamaha dealer—Starter motor turns overFuel cockTurned to “OFF”Turn the fuel cock to “ON”2-9FuelEmptyRefill as soon as possi- ble3-3Stale or contaminatedHave serviced by Yamaha dealer4-10Fuel tankWater or dirt presentHave serviced by Yamaha dealer4-11Spark plugFouled or defectiveClean or replace4-15Spark plug capNot connected or looseConnect properly4-15CrankcaseFilled with waterCrank engine with plug out until clean5-8Fuel filterClogged or water pooledHave serviced by Yamaha dealer4-11ChokeKnob moves back on its ownTighten the choke knob adjusting nut4-19Water temperature sensorFailedHave serviced by Yamaha dealer—5-1]]></page><page Index="125" isMAC="true"><![CDATA[ETROUBLEEngine runs irregu- larly or stallsWarning light or indicator blinksFuelChokeFuel filterFuel tankSpark plugSpark plug capElectrical wir- ingCarburetorFuel levelEngine oil levelEngine over- heatedLow battery voltageExhaust gas temperaturePOSSIBLE CAUSEEmptyStale or contaminatedKnob pulledClogged or water pooledWater or dirt presentFouled or defectiveIncorrect heat rangeGap incorrectLooseCracked, torn, or dam- agedLoose connectionIncorrect idle adjust- mentCloggedEmptyEmptyOil filter cloggedJet intake cloggedWater temperature sensor failedBattery voltage lowBattery terminal con- nected wrongToo highREMEDYRefill as soon as possi- bleHave serviced by Yamaha dealerPush fully inHave serviced by Yamaha dealerHave serviced by Yamaha dealerReplaceReplaceAdjustConnect properlyReplaceTighten or connect properlyAdjust idleHave serviced by Yamaha dealerRefill as soon as possi- bleRefill immediatelyCleanCleanHave serviced by Yamaha dealerChargeConnect properlyCool down enginePAGE3-34-102-104-114-114-154-154-154-15——4-22—3-33-44-125-4—4-214-212-195-2]]></page><page Index="126" isMAC="true"><![CDATA[ETROUBLEWatercraft slow or loses powerCavitationEngine over- heatedFuel filterSpark plugSpark plug capsElectrical wir- ingFuelBilgePOSSIBLE CAUSEJet intake cloggedImpeller damaged or wornJet intake cloggedCloggedFouled or defectiveIncorrect heat rangeGap incorrectLooseLoose connectionStale or contaminatedWater in bilgeCleanReplaceReplaceAdjustREMEDYHave serviced by Yamaha dealerCleanHave serviced by Yamaha dealerConnect properlyTighten or connect properlyHave serviced by Yamaha dealerDrainPAGE5-4—5-44-114-154-154-154-15—4-103-75-3]]></page><page Index="127" isMAC="true"><![CDATA[EEJU01118Emergency proceduresEJU01119Cleaning the jet intake and impellerIf weeds or debris get caught in the intake or impeller, cavitation can occur, causing jet thrust to decrease even though engine speed rises. If this condition is allowed to continue, the engine will overheat and may seize. If there is any sign that the jet intake or impeller is clogged with weeds or debris, beach the watercraft and check the intake and impeller. Always stop the engine before beaching the watercraft.@Before attempting to remove weeds or debris from the jet intake or impeller areas, shut the engine off and remove the clip from the engine shut-off switch. Severe injury or death could result from contact with the rotating parts of the jet pump.@1. Turn the watercraft on its side as shown.@q Place a suitable clean cloth or carpet- ing underneath the watercraft to pro- tect it from abrasions and scratches.q Always turn the watercraft over onto its port (left) side.q When turning the watercraft on its side, support the bow so the handle- bars cannot be bent or damaged.@WARNINGCAUTION:5-4]]></page><page Index="128" isMAC="true"><![CDATA[E2. Remove any weeds or debris from around the drive shaft, impeller, pump housing, and jet thrust nozzle.If debris is difficult to remove, consult your Yamaha dealer.@Always avoid operating your watercraft in areas where weed growth is thick. If trav- eling in weeded areas is unavoidable, operate the engine alternately at partial throttle and full throttle. Weeds tend to accumulate more at a steady speed and at trolling speed. If weeds clog the intake or impeller area and cause cavitation, fol- low the cleaning procedure above.@EJU01120Jumping the batteryIf the watercraft battery has run down, the engine can be started using a 12-volt bat- tery and jumper cables.@Battery electrolyte is poisonous and dan- gerous, causing severe burns, etc. Elec- trolyte contains sulfuric acid. Avoid contact with skin, eyes or clothing. AntidotesExternal: Flush with water.Internal: Drink large quantities of water or milk. Follow with milk of magnesia, beaten egg or vegetable oil. Call physi- cian immediately.Eyes: Flush with water for 15minutes and get prompt medical attention. Batteries give off explosive gases. Keep sparks, flame, cigarettes, etc. well away. If using or charging the battery in an enclosed area, make sure that it is well ventilated. Always shield your eyes when working near batteries.KEEP OUT OF THE REACH OF CHILDREN.@CAUTION:WARNING5-5]]></page><page Index="129" isMAC="true"><![CDATA[EJU01121Connecting the jumper cables1. Connect the positive (+) jumper cable 1 to the positive (+) terminals of both bat- teries.2. Connect one end of the negative (–) jumper cable 2 to the negative (–) termi- nal of the booster battery 3.3. Connect the other end of the negative (–) cable to an unpainted bolt on the cylinder head.@Do not connect the end of the jumper cable to the negative (–) terminal on the watercraft battery! Be sure all connec- tions are secure and correct before attempting to start the engine. Any wrong connection may damage the elec- trical system.@4. Start the engine, and then disconnect the cables by reversing the steps above.@q Never push the start switch while the engine is running.q Do not operate the start switch for more than 5seconds, otherwise the battery will be discharged and the engine will not start. Also, the starter motor may be damaged. If the engine does not start in 5 seconds, release the start switch, wait 15 seconds, and try again.@ECAUTION:CAUTION:5-6]]></page><page Index="130" isMAC="true"><![CDATA[EJU01122Towing the watercraftIf the watercraft becomes inoperative in the water, it can be towed to shore.If the watercraft must be towed in an emergency using a tow line, the operator should ride the watercraft, holding onto the handlebars.@q Tow the watercraft slowly; water may enter the air intake and flood the engine compartment if the watercraft is towed too fast.q Towthewatercraftusingtheboweye1 only.q The bow must be kept up out of the water during towing to prevent water from entering the engine compart- ment.@@q Thewatercraftshouldonlybetowedin an emergency.q Thetowlineshouldbelongenoughso that the watercraft will not collide with the towing boat when slowing down. A good rule of thumb is a tow line which is three times the combined length of the towing boat and the watercraft. A shorter length of rope can be used if the watercraft is towed very slowly.q The operator of the towing boat must keep speed to a minimum and avoid traffic or obstacles which could be a hazard to the rider on the watercraft.@ECAUTION:WARNING5-7]]></page><page Index="131" isMAC="true"><![CDATA[5-8EJU01123Submerged watercraftIf the watercraft is submerged or flooded with water, follow the procedure below and consult a Yamaha dealer as soon as possi- ble. Failure to do so may result in serious engine damage!1. Beach the watercraft and remove thestern drain plugs to drain the water fromthe engine compartment.2. Turn the fuel cock knob to “OFF.”3. Remove the spark plugs and dry themwith a cloth.4. Without reinstalling the spark plugs,crank the engine until all the water in thecylinders has been drained.5. Install the stern drain plugs and thespark plugs.6. Turn the fuel cock to “ON.”7. Launch the watercraft into the water, andthen run the engine for at least 10 minutes. If the engine will not start, repeat steps above.8. Turn the engine off. Turn the fuel cock to “OFF.”9. Have the watercraft inspected by a Yamaha dealer as soon as possible.E]]></page><page Index="132" isMAC="true"><![CDATA[E–MEMO–]]></page><page Index="133" isMAC="true"><![CDATA[EJU01124APPENDIXLimited warranty ...................................6-1 YAMAHA EXTENDED SERVICE(Y.E.S.) ..................................................6-3 Index .....................................................6-4E6]]></page><page Index="134" isMAC="true"><![CDATA[6-1EEJU01200Limited warrantyYAMAHA MOTOR CORPORATION, U.S.A. WATERCRAFT LIMITED WARRANTYYamaha Motor Corporation is proud of its heritage and reputation for producing products with high standards of quality and workman- ship. Product excellence provides the cornerstone for our commitment to customer satisfaction. The Yamaha Watercraft Limited War- ranty is your assurance of this commitment.This warranty provides you with protection against the expense of repairs for your watercraft that are required as a result of defects in materials or workmanship. When maintained and utilized in the prescribed manner, you can count on your Yamaha watercraft to pro- vide reliable service.This warranty provides you with specific coverage and notes your responsibilities in maintaining and operating your watercraft. Please take the time to read and become familiar with this warranty.PERIOD OF WARRANTY. Any new Yamaha watercraft purchased for pleasure use from an authorized Yamaha dealer in the United States, will be warranted against defects in material or workmanship for a period of one (1) year from date of purchase, subject to exclusions noted herein. Any Yamaha Watercraft purchased and utilized for commercial applications will be warranted for a period of ninety [90] days from the date of purchase, subject to exclusions noted herein. Replacement parts used in warranty repairs will be war- ranted for the balance of the applicable warranty period.The warranty described here applies to watercrafts purchased and registered for use in the United States only. For warranty provisions outside the United States, contact the particular country’s local Yamaha distributor.OBTAINING REPAIRS UNDER WARRANTY. During the period of warranty, any authorized Yamaha dealer will, free of charge, repair or replace, at Yamaha’s option, any parts adjudged defective by Yamaha due to faulty workmanship or material from the factory. All parts replaced under warranty will become the property of Yamaha Motor Corporation, U.S.A.CUSTOMER’S RESPONSIBILITY. Under the terms of this warranty, the customer will be responsible for ensuring that the watercraft is properly operated, maintained, and stored as specified in the applicable Owner’s/Operator’s Manual.The owner of the watercraft shall give notice to an authorized Yamaha dealer of any and all apparent defects within ten [10] days of dis- covery and make the watercraft available at that time for inspection and repairs at the dealer’s place of business.GENERAL EXCLUSIONS FROM WARRANTY. This warranty will not cover the repair of damage if the damage is a result of abuse or neglect of the product. Examples of abuse and neglect include, but are not limited to:1. Racing or competition use, modification of original parts abnormal strain.2. Lack of proper maintenance and off season storage as described in the Owner’s/Operator’s Manual, installation of parts or accesso-ries that are not equivalent in design and quality to genuine Yamaha parts.3. Use of lubricants, oils, and fuel/oil mixtures that are not suitable for watercraft motor use. 4. Damage as a result of accidents, collisions, contact with foreign materials, or submersion. 5. Growth of marine organisms on motor or hull surfaces.6. Normal deterioration.7. Gel coat stress cracks.SPECIFIC PARTS EXCLUDED FROM WARRANTY.Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, fuel filters, impeller and liner, and anodes are not covered by warranty. Charges for transporting the watercraft to and from an authorized Yamaha dealer are excluded from warranty cov- erage.TRANSFER OF WARRANTY. Transfer of the warranty from the original purchaser to any subsequent purchaser is possible by having the watercraft inspected by an authorized Yamaha dealer and requesting the dealer to submit a change of registration to Yamaha Motor Corporation. U.S.A. within ten [10] days of the transfer.EMISSION CONTROL SYSTEM WARRANTY. Yamaha warrants to the ultimate purchaser and each subsequent, that this engine is designed, built, and equipped so as to conform at the time of sale with applicable regulations under section 213 of the Clean Air Act and this engine is free from defects in materials and workmanship which cause said engine to fail to conform with applicable regula- tions for one (1) year from date of purchase.YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WAR- RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITS STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, U.S.A. AND EXCLUDED FROM THIS WARRANTY.SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS OF USE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.]]></page><page Index="135" isMAC="true"><![CDATA[6-2ETHIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.YAMAHA MOTOR CORPORATION, U.S.A. Post Office Box 6555 Cypress, California 90630WARRANTY QUESTIONS AND ANSWERSQ. What costs are my responsibility during the warranty period?A. The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision dam-ages.Q. What are some examples of “abnormal” strain, neglect, or abuse?A. These terms are general and overlap each other in areas. Specific examples include:Running the watercraft out of oil, operating the machine with a broken or damaged part which causes another part to fail, and so on. If you have any specific questions on operation or maintenance, please contact your Yamaha dealer for advice.Q. Does the warranty cover incidental costs such as transportation due to a failure? A. No. The warranty is limited to repair of the watercraft itself.Q. May I perform any or all of the recommended maintenance shown in the Owner’s/Operator’s Manual instead of having the dealer do them?A. Yes, if you are a qualified mechanic and follow the procedures specified in the Owner’s/Operator’s and Service Manual. We do rec- ommend, however, that items requiring special or equipment be done by a Yamaha dealer.Q. Will the warranty be void or cancelled if I do not operate or maintain my new watercraft exactly as specified in the Owner’s/Opera- tor’s Manual?A. No. The warranty on a new watercraft cannot be “voided” or “cancelled”. However, if a particular failure is caused by operation or maintenance other than as shown in the Owner’s/Operator’s Manual, that failure may not be covered under warranty.Q. What responsibility does my dealer have under this warranty? A. Each Yamaha dealer is expected to:1.Completely set up each new watercraft before sale.2.Explain the operation, maintenance, and warranty requirements to your satisfaction at the time of sale, and upon your request at anylater date. In addition, each Yamaha dealer is held responsible for his setup, service and warranty repair work.Q. Is the warranty transferable to second owners?A. Yes. The remainder of the existing warranty can be transferred upon request. The unit has to be inspected and re-registered by anauthorized Yamaha dealer for the policy to remain effective.CUSTOMER SERVICEIf your watercraft requires warranty service, you must take it to any authorized Yamaha dealer within the continental United States. Be sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises regard- ing warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, this person is in the best position to help you. If you are still not satisfied and require additional assistance, please write:YAMAHA MOTOR CORPORATION U.S.A. CUSTOMER RELATIONS DEPARTMENT P.O. Box 6555Cypress, California 90630CHANGE OF ADDRESSThe federal government requires each manufacturer to maintain a complete, up-to-date list of all first purchasers against the possibility of a safety-related defect and recall. This list is complied from the purchase registrations sent to Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.If you should move after you have purchased your new watercraft, please advise us of your new address by sending a postcard listing your Yamaha model name, engine number, dealer number [or dealer’s name] as it is shown on your warranty card, your name and new mailing address.Mail to:YAMAHA MOTOR CORPORATION, U.S.A. P.O. Box 6555Cypress, California 90630 Attention: Warranty DepartmentThis will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.]]></page><page Index="136" isMAC="true"><![CDATA[EJU01201YAMAHA EXTENDED SERVICE (Y.E.S.)Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.).q Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum ownersatisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.q Y.E.S. is flexible. You choose the plan that is right for you: 12 months, 24 months, or 36 monthsbeyond your warranty period.q Y.E.S. is designed and administered by the same Yamaha people who handle your warranty and it shows in the comprehensive coverage benefits. There are no mileage limitations. Cover- age is not limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers manufacturing defects just like the warranty. See the sample contract at your Yamaha dealer to see how comforting uninterrupted factory-backed protection can be.q You do not have to pay anything for covered repairs. There is no deductible to pay, and repairs are not “pro-rated.” You do not have any “out-of-pocket” expenses for covered repairs.q In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost. TRIP gives you up to $150 reimbursement per occurrence for any reasonable expenses you incur because your Yamaha needs covered service: replacement vehicle rental, emergency towing, phone calls, even food and lodging when you are away from home. This superb cover- age goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as covered repairs during your entire Y.E.S. plan period.q Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.q Y.E.S. coverage is transferable to a new owner if you sell or trade-in. That can make yourYamaha much more valuable!This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service.We urge you to act now. You will get the excellent benefits of TRIP coverage right away, and you will rest easy knowing you will have strong factory-backed protection even after your Yamaha Limited Warranty expires. You can also save money: Y.E.S. costs less within the first 90 days after you buy your Yamaha. See your dealer today!A special note:If visiting your dealer is not convenient, contact Yamaha with your Primary ID number (your engine number). We will be happy to help you get the Y.E.S. coverage you need.Yamaha Service Marketing P.O. Box 6555Cypress, CA 90630(714) 761-76316-3E]]></page><page Index="137" isMAC="true"><![CDATA[EEJU01125Engine overheat warning system .......... 2-17 Engine serial number .............................. 1-1 Engine shut-off cord (lanyard)...............3-12 Engine shut-off switch ........................... 2-10 Engine stop switch ................................ 2-10 Enjoy your watercraft responsibly .........1-21 Exhaust temperature warningindicator ................................................. 2-29 Exhaust temperature warningsystem ................................................... 2-19 FFilling the fuel tank .................................. 3-3 Filling the oil tank ....................................3-4 Fire extinguisher......................................3-9 Fishing vessel right-of-way....................1-18 Flushing the cooling system....................4-1 Front seat ................................................ 2-6 Front storage compartment...................2-30 Fuel and oil..............................................3-1 Fuel and oil systems ...............................3-6 Fuel cock knob ........................................ 2-9 Fuel filter ...............................................4-11 Fuel meter ............................................. 2-24 Fuel system.............................................4-4 Fuel tank ...............................................4-11 Fuel tank filler cap ................................... 2-8 Fuel warning indicator ........................... 2-27 GGasohol ................................................... 3-2 Gasoline .................................................. 3-1 Getting to know your watercraft ............3-20 Give-way vessel .................................... 1-16 Glove compartment...............................2-31 H Handgrip................................................2-16 Hazard information................................1-13 Hood........................................................2-7 Hour meter ............................................2-26 Hull Identification Number (HIN)..............1-1 IIdentification numbers ............................. 1-1 Important labels.......................................1-3Index2-stroke engine oil...................................3-2AAdjusting the carburetor ........................ 4-22 Adjusting the choke cable ..................... 4-19 Adjusting the trolling speed ................... 4-22 Approval label of Emission control certificate ................................................. 1-2 BBattery..............................................3-8, 4-5 Battery warning indicator....................... 2-29 Beaching the watercraft ........................ 3-31 Bilge ........................................................ 3-7 Bleeding the oil injection pump ............. 4-23 Boarding alone ...................................... 3-24 Boarding and starting in deep water ..... 3-24 Boarding with passengers.....................3-25 Bow down.............................................. 2-16 Bow up .................................................. 2-16 CCapsized watercraft .............................. 3-26 Caution labels ......................................... 1-6 Choke knob ........................................... 2-10 Cleaning and adjusting thespark plugs............................................4-15 Cleaning the jet intake and impeller ........ 5-4 Cleaning the watercraft ........................... 4-6 Clock ..................................................... 2-25 Connecting the jumper cables................. 5-6 Cooling water pilot outlet..............2-12, 3-13 Crossing ................................................ 1-17 Cruising limitations .................................. 1-9 DDocking the watercraft .......................... 3-31EEmergency procedures ........................... 5-4 Emission control information ................... 1-2 Engine break-in ..................................... 3-14 Engine compartment ............................... 3-6 Engine oil meter .................................... 2-25 Engine overheat warning indicator........2-286-4]]></page><page Index="138" isMAC="true"><![CDATA[EInspecting and adjusting thethrottle cable.......................................... 4-13 Inspecting the battery ............................ 4-20 Inspecting the fuel system..................... 4-10 Inspecting the oil injection system......... 4-12 Inspecting the QSTS mechanism.......... 4-14 Inspecting the shift cable....................... 4-13 Inspecting the steering cable ................ 4-13 JJet unit................................................... 3-12 Jumping the battery................................. 5-5 LLabel location .......................................... 1-3 Launching the watercraft ....................... 3-16 Learning to operate your watercraft ...... 3-20 Leaving the watercraft ........................... 3-19 Limitations on who may operate the watercraft ................................................ 1-8 Limited warranty ...................................... 6-1 Location of main components ................. 2-1 Lubrication............................................... 4-3 Lubrication points .................................. 4-16 MMaintenance and adjustments ................ 4-7 Manufactured date label.......................... 1-2 Meeting ................................................. 1-17 Multifunction meter ....................... 2-20, 3-13 NNarrow channels and bends ................. 1-18 OOil filter .................................................. 4-12 Oil tank .................................................. 4-12 Oil tank filler cap...................................... 2-8 Oil warning indicator.............................. 2-28 Operating your watercraft...................... 3-20 Operation .............................................. 3-14 Operation of controls and otherfunctions .................................................. 2-5 Operation requirements ........................ 1-10 Other labels ............................................. 1-7 Other sources........................................ 1-20 Other special situations ......................... 1-18 Overtaking ............................................. 1-18Owner’s/Operator’s Manual andtool kit ...................................................... 4-8 PPADLOC initial setting...........................2-21 P ADLOC (Programmable digital locking ignition)..................................................2-21 Periodic maintenance chart..................... 4-9 Post-operation checks...........................3-33 Pre-operation check list...........................3-5 Pre-operation check points ..................... 3-6 Pre-operation checks .............................. 3-5 Primary Identification (PRI-ID)number .................................................... 1-1 QQuick Shift Trim System (QSTS)selector .................................................. 2-15 RReading buoys and other markers ........ 1-18 Rear seat.................................................2-5 Recommended equipment .................... 1-12 Replacing the fuse ................................ 4-23 Reverse on waterways .......................... 3-32 Riding watercraft with passengers ........ 3-21 Rough water operation .......................... 3-32 Rules of the Road ................................. 1-16 Rules when encountering vessels.........1-17 SSafety information ................................... 1-8 Sailing vessel right-of-way .................... 1-18 Seat storage compartment .................... 2-31 Selecting “P ADLOC” mode ................... 2-22 Shift lever .............................................. 2-14 Shift lever and reverse gate .................. 3-11 Specifications ........................................ 4-24 Speedometer ......................................... 2-24 Stand-on vessel .................................... 1-16 Starting and boarding in shallowwater ..................................................... 3-23 Starting from a dock .............................. 3-23 Starting the engine ................................ 3-16 Starting the watercraft ........................... 3-22 Start switch............................................2-11 Steering and sailing rules ...................... 1-166-5]]></page><page Index="139" isMAC="true"><![CDATA[6-6ESteering system ...........................2-12, 3-10 Stopping the engine .............................. 3-19 Stopping the watercraft ......................... 3-30 Storage.................................................... 4-1 Storage compartments..........................2-30 Submerged watercraft.............................5-8 Switches ................................................ 3-13 TT achometer ........................................... 2-23 Throttle .................................................. 3-10 Throttle lever ......................................... 2-11 Tilt lever................................................. 2-13 To get more boating safetyinformation ............................................ 1-20 Towing the watercraft..............................5-7 Transporting .......................................... 3-35 Tripmeter ............................................... 2-27 Trip timer ............................................... 2-26 Troubleshooting ...................................... 5-1 Troubleshooting chart ............................. 5-1 Turning the watercraft ........................... 3-28 UUnited States Coast Guard ................... 1-20WWarning labels ........................................ 1-4 Watercraft characteristics...................... 1-13 Watercraft Education and Training........ 1-20 Water separator ...................................... 3-7 Water-skiing .......................................... 1-14 YYAMAHA EXTENDED SERVICE(Y .E.S.).................................................... 6-3]]></page><page Index="140" isMAC="true"><![CDATA[]]></page><page Index="141" isMAC="true"><![CDATA[]]></page><page Index="142" isMAC="true"><![CDATA[YAMAHA MOTOR CORPORATION, USAPrinted in USAJuly 2001—2.0 × 1 CR F0V-F8199-11 (XA1200A-A)(E)Printed on recycled paper]]></page></pages></Search>