﻿<?xml version="1.0" encoding="utf-8" standalone="no"?><Search><pages Count="117"><page Index="1" isMAC="true"><![CDATA[2015 WaveRunner VXS VXROWNER’S/OPERATOR’S MANUALU.S.A. EditionLIT-18626-10-55 F2W-F8199-10Read this manual carefully before operating this watercraft.]]></page><page Index="2" isMAC="true"><![CDATA[]]></page><page Index="3" isMAC="true"><![CDATA[Read this manual carefully before operating this watercraft. This manual should stay with the WaveRunner if it is sold.]]></page><page Index="4" isMAC="true"><![CDATA[]]></page><page Index="5" isMAC="true"><![CDATA[To the owner/operatorThank you for choosing a Yamaha watercraft. This owner’s/operator’s manual contains in- formation you will need for proper operation, maintenance, and care. A thorough under- standing of these simple instructions will help you to obtain maximum enjoyment from your new Yamaha. If you have any questions about the operation or maintenance of your watercraft, please consult a Yamaha dealer. In this manual, information of particular im- portance is distinguished in the following ways:This is the safety alert symbol. It is usedto alert you to potential personal injury haz-ards. Obey all safety messages that followthis symbol to avoid possible injury or death. EWJ00072A WARNING indicates a hazardous situa- tion which, if not avoided, could result in death or serious injury.ECJ00092NOTICEA NOTICE indicates special precautions that must be taken to avoid damage to the watercraft or other property.TIP:A TIP provides key information to make pro- cedures easier or clearer.Important manual informationEJU30183EJU40401Because Yamaha has a policy of continuing product improvement, this product may not be exactly as described in this owner’s/oper- ator’s manual. Specifications are subject to change without notice.This manual should be considered a perma- nent part of this watercraft and should remain with it even if the watercraft is subsequentlysold. EJU30223WaveRunner VXS / VXR OWNER’S/OPERATOR’S MANUAL ©2014 by Yamaha Motor Corporation, U.S.A.1st Edition, December 2014All rights reserved.Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in U.S.A.P/N LIT-18626-10-55WARNING]]></page><page Index="6" isMAC="true"><![CDATA[Table of contentsGeneral and important labels...........1Identification numbers .................... 1 Primary Identification (PRI-ID)number............................................ 1 Hull Identification Number (HIN)......... 1 Engine serial number.......................... 1Emission control information .......... 2 Approval label of emission controlcertificate........................................ 2 Manufactured date label .................... 2 Star labels .......................................... 3Important labels .............................. 5 Warning labels.................................... 6 Other labels ........................................ 8Safety information ........................... 10Limitations on who may operatethe watercraft............................. 10 Cruising limitations........................ 11 Operation requirements ................ 13 Recommended equipment ........... 15 Hazard information........................ 16 Watercraft characteristics ............. 16 Wakeboarding and water-skiing ... 18 Rules of the Road ......................... 19To get more boating safety information................................. 23Enjoy your watercraft responsibly................................. 24Description....................................... 26Watercraft glossary ....................... 26 Location of main components ...... 27Control function operation ............. 31Watercraft control functions ......... 31 Remote control transmitter .............. 31 Yamaha Security System................. 32 Engine stop switch .......................... 33 Engine shut-off switch .................... 33 Start switch ..................................... 33 Throttle lever .................................... 34RiDE lever......................................... 34 Steering system................................ 35 Cooling water pilot outlet ................. 35 Water separator................................ 35Watercraft operation ...................... 37Watercraft operation functions ..... 37 Shift system...................................... 37 Electric trim system.......................... 39Watercraft operation modes......... 41 Low RPM Mode ............................... 41Instrument operation ...................... 43Multifunction information center... 43 Information display........................... 43 Hour meter ....................................... 47 Voltmeter.......................................... 48Equipment operation ...................... 49Equipment..................................... 49 Seats ................................................ 49 Handgrip........................................... 50 Reboarding step (VXR) ..................... 50 Bow eye............................................ 51 Stern eyes ........................................ 51 Cleat................................................. 51 Storage compartments .................... 52 Fire extinguisher holder and cover... 54Operation and handling requirements ................................... 56Fuelrequirements......................... 56 Fuel................................................... 56 Engine oil requirements ................ 58 Engine oil.......................................... 58 Draining the bilge water................ 60 Draining the bilge water on land....... 60 Draining the bilge water on water .... 60]]></page><page Index="7" isMAC="true"><![CDATA[Transporting on a trailer ................ 61Table of contentsRustproofing..................................... 90Maintenance....................................91Maintenance................................. 91 Tool kit.............................................. 91 Removing and installing the enginecover............................................. 91 Periodic maintenance chart ............. 93 Engine oil and oil filter ...................... 94Specifications.................................. 95Specifications............................... 95Trouble recovery ............................. 96Troubleshooting............................ 96 Troubleshooting chart ...................... 96 Emergency procedures ................ 99Cleaning the jet intake andimpeller ......................................... 99Raising the reverse gate................. 100 Jumping the battery ....................... 100 Replacing the fuses ........................ 101 Towing the watercraft..................... 103 Submerged watercraft ................... 103Consumer information ................. 105Limited warranty ......................... 105 YAMAHA EXTENDED SERVICE(Y.E.S.)..................................... 107Index............................................... 108First-timeoperation........................62Engine break-in ............................. 62Pre-operation checks ..................... 63Pre-operationchecklist.................... 63 Pre-operation check points........... 65 Pre-launch checks ........................... 65 Post-launch checks ......................... 71Operation ......................................... 74Operating your watercraft ............. 74 Getting to know your watercraft ...... 74 Learning to operate yourwatercraft ...................................... 74 Riding position ................................. 75 Launching the watercraft ................. 75 Starting the engine on water ............ 75 Stopping the engine ......................... 76 Leaving the watercraft...................... 76 Operating the watercraft .................. 76 Turning the watercraft ...................... 77 Stopping the watercraft ................... 78 Operating the watercraft in reverseor neutral....................................... 79 Boarding the watercraft ................... 80 Starting off........................................ 82 Capsized watercraft ......................... 83 Beaching and docking thewatercraft...................................... 84 Operating in weeded areas .............. 84 After removing the watercraft fromthe water....................................... 84Care and storage............................. 86Post-operation care ...................... 86 Flushing the cooling waterpassages....................................... 86 Cleaning the watercraft .................... 87 Battery care...................................... 87Long-term storage ........................ 90 Cleaning........................................... 90 Lubrication ....................................... 90]]></page><page Index="8" isMAC="true"><![CDATA[General and important labelsEJU30263EJU30301Hull Identification Number (HIN)The HIN is stamped on a plate attached to the aft deck.Identification numbersRecord the Primary Identification (PRI-ID) number, Hull Identification Number (HIN), and engine serial number in the spaces provided for assistance when ordering genuine parts from a Yamaha dealer. Also record and keep these ID numbers in a separate place in caseyour watercraft is stolen.EJU42521Primary Identification (PRI-ID) number The PRI-ID number is stamped on a plate at-tached inside the engine compartment. (See page 49 for seat removal and installation pro- cedures and page 54 for information on the removable watertight storage compartment.) MODEL:VX1800-P (VXS) VX1800A-P (VXR)1 Hull Identification Number (HIN) locationEJU30312Engine serial numberThe engine serial number is stamped on a plate attached to the engine unit. (See page 49 for seat removal and installation proce- dures.)1111 Primary Identification (PRI-ID) number loca- tionPRI-I.D.MODEL F2W YAMAHA MOTOR CO., LTD.ASSEMBLED IN U.S.A. FROM AMERICAN AND JAPANESE COMPONENTS.ASSEMBLÉ AUX ÉTATS-UNIS DE PIÈCES AMÉRICAINES ET JAPONAISES.F2W11 Engine serial number location]]></page><page Index="9" isMAC="true"><![CDATA[EJU30353Emission control informationThis engine conforms to U.S. Environmental Protection Agency (EPA) and/or California Air Resources Board (CARB) regulations for ma- rine SI engines applicable at the time of man- ufacture.This engine is certified to operate on regularunleaded gasoline.EJU42511Approval label of emission controland page 54 for information on the removable watertight storage compartment.)certificate 1This label is attached to the top of the cylin- der head and to the inside of the engine com- partment. (See page 49 for seat removal and installation procedures, page 91 for engine cover removal and installation procedures,1 Emission control information label location1General and important labels1 Emission control information label locationEMISSION CONTROL INFORMATION ENGINE FAMILY:THIS ENGINE CONFORMSTO CALIFORNIA AND U.S. EPA EXHAUST REGULATIONS FOR SI MARINE ENGINES. REFERTOTHE OWNER’S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS. THIS VESSEL MEETS U.S. EPA EVAP STANDARDS.FELS (HC+NOx/CO) : g/kW-hr TROLLING SPEED : rpmFUEL : UNLEADED REGULAR GASOLINE CERTIFIED COMPONENTS :MAX POWER : kW SPARK PLUG :VALVE LASH (mm) IN :DISPLACEMENT : SPARK PLUG GAP (mm) :EX :litersYAMAHA MOTOR CO., LTD.EJU40491Manufactured date labelThis label is attached to the top of the cylin- der head. (See page 49 for seat removal and installation procedures and page 91 for en-2]]></page><page Index="10" isMAC="true"><![CDATA[General and important labelsgine cover removal and installation proce- dures.)Watercraft and Outboard marine engine 2001 exhaust emission standards. Engines meet- ing these standards have 75% lower emis- sions than conventional carbureted two- stroke engines. These engines are equivalent to the U.S. EPA’s 2006 standards for marine engines.11 Manufactured date label locationEJU30441Star labelsThis watercraft is labeled with a California Air Resources Board (CARB) star label. See be- low for a description of your particular label.Two Stars - Very Low EmissionThe two-star label identifies engines that meet the Air Resources Board’s Personal Watercraft and Outboard marine engine 2004 exhaust emission standards. Engines meet- ing these standards have 20% lower emis- sions than One Star-Low Emission engines.11 Star label locationOne Star - Low EmissionThe one-star label identifies engines that meet the Air Resources Board’s PersonalThree Stars - Ultra Low EmissionThe three-star label identifies engines that meet the Air Resources Board’s Personal Watercraft and Outboard marine engine 2008 exhaust emission standards or the Sterndrive and Inboard marine engine 2003-2008 ex- haust emission standards. Engines meeting3]]></page><page Index="11" isMAC="true"><![CDATA[General and important labelsthese standards have 65% lower emissions than One Star-Low Emission engines.Four Stars - Super Ultra Low EmissionThe four-star label identifies engines that meet the Air Resources Board’s Sterndrive and Inboard marine engine 2009 exhaust emission standards. Personal Watercraft and Outboard marine engines may also comply with these standards. Engines meeting these standards have 90% lower emissions than One Star-Low Emission engines.4]]></page><page Index="12" isMAC="true"><![CDATA[General and important labelsEJU30453Important labelsRead the following labels before using this watercraft. If have any questions, consult a Yamaha dealer.78 624 3911110 55]]></page><page Index="13" isMAC="true"><![CDATA[12General and important labelsEJU35914Warning labelsIf any of these labels are damaged or missing, contact a Yamaha dealer for replacements.F1S-U415B-016]]></page><page Index="14" isMAC="true"><![CDATA[General and important labels7]]></page><page Index="15" isMAC="true"><![CDATA[EJU35926Other labelsGeneral and important labels67F1S-U41G1-018910(F1S-U41E1-01)F0V-U41F5-018]]></page><page Index="16" isMAC="true"><![CDATA[General and important labelsThe following label indicates the correct direction to upright a capsized watercraft.9]]></page><page Index="17" isMAC="true"><![CDATA[EJU30672EJU30732Limitations on who mayoperate the watercraft  Yamaha recommends a minimum operator age of 16 years old.Adults must supervise use by minors. Know the operator age and training re- quirements for your state. A boating safety course is recommended and may be re- quired in your state. You can find local rules by contacting the United States Coast Guard (USCG), the National Association of State Boating Law Administrators, or your local Power Squadron.  This watercraft is designed to carry the op- erator and up to 2 passengers. Never ex- ceed the maximum load limit or allow more than 3 persons (or 2 persons if a wake- boarder or water-skier is being pulled) to ride the watercraft at any time.  Do not operate the watercraft with any pas- sengers on board until you have consider- able practice and experience riding alone. Operating the watercraft with passengers requires more skill. Take the time to be- come accustomed to the handling charac-The safe use and operation of this water- craft is dependent upon the use of proper riding techniques, as well as upon the common sense, good judgment, and ex- pertise of the operator. Every operator should know the following requirements before riding the watercraft.  Before operating the watercraft, read this owner’s/operator’s manual, the Riding Practice Guide, the Riding Instruction card, and all labels on the watercraft. Also, watch the Basic Orientation Video provided with your watercraft. These materials should give you an understanding of the watercraft and its operation.  Never allow anyone to operate this water- craft until they too have read this own- er’s/operator’s manual, the Riding Practice Guide, the Riding Instruction card, and all labels, and, if possible, watched the Basic Orientation Video.Showing them the video may help reinforce the information contained in these materi- als.Safety informationMaximum load:240 kg (530 lb)Load is the total weight of cargo, op- erator, and passengers.10]]></page><page Index="18" isMAC="true"><![CDATA[Safety informationteristics of the watercraft before trying any difficult maneuvers.EJU43321Cruising limitations  Scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others.  Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft.  Do not follow directly behind watercraft or other boats.  Do not go near others to spray or splash them with water.  Take early action to avoid collisions. Re- member, watercraft and other boats do not have brakes. In addition, the Reverse with Intuitive Deceleration Electronics (RiDE) system is not a braking device for avoiding dangerous situations. The RiDE system is an electronic system for controlling the en- gine speed and reverse gate, which is lo- cated near the jet thrust nozzle. The RiDE lever located at the left handlebar grip can be used to change the direction of the jet thrust so that the watercraft moves in re- verse or is in neutral. The RiDE system as- sists the operator when slowing down and during slow-speed maneuvering, such as launching, beaching, and docking.  Avoid sharp turns, slowing down rapidly by squeezing the RiDE lever forcefully, and other maneuvers that make it hard for oth-11]]></page><page Index="19" isMAC="true"><![CDATA[ers to avoid you or understand where youare going.  Avoid areas with submerged objects orshallow water.  Do not release the throttle lever when tryingto steer away from objects—you need throttle to steer. Always check throttle and steering controls before starting the water- craft.  Ride within your limits and avoid aggres- sive maneuvers to reduce the risk of loss of control, ejection, and collision.  This is a high performance boat—not a toy. Sharp turns or jumping wakes or waves can increase the risk of back/spinal injury (paralysis), facial injuries, and broken legs, ankles, and other bones. Do not jump wakes or waves.  Do not operate the watercraft in rough wa- ter, bad weather, or when visibility is poor; this may lead to an accident causing injury or death. Be alert to the possibility of ad- verse weather. Take note of weather fore- casts and the prevailing weather conditions before setting out on your wa- tercraft.  As with any water sport, you should not op- erate your watercraft without someone else nearby. If you operate further than swim- ming distance from shore, you should be accompanied by another boat or water- craft, but make sure you stay a safe dis- tance away. It’s good, common sense.  Never operate in water that is less than 60 cm (2 ft) deep from the bottom of the wa- tercraft, otherwise you increase your Safety informationchance of hitting a submerged object, which could result in injury.60 cm (2 ft)This watercraft is not equipped with light- ing required for night operation. Do not op- erate the watercraft after sunset or before dawn, otherwise you increase the risk of colliding with another boat, which could re- sult in severe injury or death. Follow navigation rules, and state/provin- cial and local laws that apply to watercraft.12]]></page><page Index="20" isMAC="true"><![CDATA[Safety informationEJU43120Operation requirements  All riders must wear a U.S. Coast Guard (USCG) approved personal flotation device (PFD) that is suitable for personal water- craft use.  Wear protective clothing. Severe internal injuries can occur if water is forced into body cavities as a result of falling into the water or being near the jet thrust nozzle. Normal swimwear does not adequately protect against forceful water entry into the rectum or vagina. All riders must wear a wetsuit bottom or clothing that provides equivalent protection. Such clothing in- cludes thick, tightly woven, sturdy and snug-fitting apparel such as denim, but does not include spandex or similar fab- rics, like those used in bicycle shorts.1 USCG approved PFD 2 Wetsuit bottom  Eye protection is recommended to keep wind, water, and glare from the sun out of your eyes while you operate your water- craft. Restraining straps for eyewear are made which are designed to float should your eyewear fall in the water.Footwear and gloves are recommended.  Helmets meeting Snell or DOT standards are required for IJSBA-sanctioned races. You must decide whether to wear a helmet while you ride for recreation. You shouldknow that a helmet could help protect you in certain kinds of accidents and that it could injure you in others.A helmet is designed to provide some head protection. Although helmets cannot pro- tect against all foreseeable impacts, a hel- met might reduce your injuries in a collision with a boat or other obstacle.A helmet may have potential safety haz- ards, as well. Falling into the water could risk the chance of the helmet catching wa- ter, commonly known as “bucketing”, and the resulting strain on your neck could cause choking, severe and permanent neck injuries, or death. A helmet could also increase the risk of an accident if it reduces your vision or hearing, or if it distracts you or increases your fatigue.How should you decide if a helmet’s poten- tial safety benefits outweigh its potential risks for you? Consider your particular rid- ing conditions. Consider factors such as your riding environment and your riding style and ability. Also consider the likeli- hood of traffic congestion, and the water surface conditions.If you decide to wear a helmet based upon your riding circumstances, choose one carefully. Look for a helmet designed for personal watercraft use, if possible. Con- sider a helmet meeting Snell or DOT stan- dards. If you will be engaging in closed- course competition, follow the helmet re- quirements of the sanctioning organization.  Never operate the watercraft after consum- ing alcohol or taking other drugs.  For reasons of safety and proper care of the watercraft, always perform the pre-op- eration checks listed on page 63 before op- erating the watercraft.13]]></page><page Index="21" isMAC="true"><![CDATA[  The operator should grip the handlebars firmly with both hands and the passengers should hold on firmly, either to the person in front of them or to the handgrip provid- ed.  The operator and passengers should al- ways keep their feet on the floor of the foot- well when the watercraft is in motion. Lifting your feet increases the chances of losing your balance, or hitting objects out- side the watercraft with your feet. Do not give a ride to children if their feet cannot reach the floor of the footwell.  Never allow a passenger to ride in front of the operator.  Always consult your doctor on whether it is safe for you to ride this watercraft if you are pregnant or in poor health.  Do not attempt to modify this watercraft. Modifications to your watercraft may re- duce safety and reliability, and render the watercraft unsafe or illegal for use.  Attach the engine shut-off cord (lanyard) to your left wrist and keep it free from the han- dlebars so that the engine stops if you, the operator, fall off. After riding, remove the engine shut-off cord (lanyard) from the wa-Safety informationtercraft to avoid accidental starting or un- authorized use by children or others.  Scan carefully for swimmers and stay away from swimming areas. Swimmers are hard to see and you could accidentally hit some- one in the water.  Avoid being hit by another boat. You should always take the responsibility to watch for traffic; other boaters may not be watching for you. If they do not see you, or if you maneuver more quickly than other boaters expect, you risk a collision.  Maintain a safe distance from other boats and watercraft, and also watch for ski ropes or fishing lines. Obey the “Rules of the Road” and be sure to check behind you before making a turn or slowing down. (See “Rules of the Road” on page 19.)  According to the USCG, boats under 6.1 m (20 ft) in length like your watercraft must carry a fire extinguisher of a B-1 classifica- tion, with a capacity of two pounds or more when navigating in waters under USCG ju- risdiction. In addition, most state and local14]]></page><page Index="22" isMAC="true"><![CDATA[Safety informationboating laws also require that the fire extin- guisher be approved by the USCG.EJU30831Recommended equipmentThe following items should be carried on board your watercraft:  Sound-signaling deviceYou should carry a whistle or other sound- signaling device that can be used to signal other boats. See “Rules of the Road” for more information.  Visual distress signalsIt is recommended that a U.S. Coast Guard approved pyrotechnic device be stored in a waterproof container on your watercraft. A mirror can also be used as an emergency signal. Contact a Yamaha dealer or the U.S. Coast Guard for more information.  WatchA watch is helpful so you will know how long you have been operating the water- craft.  TowlineA towline can be used to tow a disabled watercraft in an emergency.15]]></page><page Index="23" isMAC="true"><![CDATA[EJU42474EJU42414Watercraft characteristics  Jet thrust turns the watercraft. Releasing the throttle lever completely produces only minimum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to steer without throttle. This model is equipped with the Yamaha Engine Management System (YEMS) that includes an off-throttle steering (OTS) sys- tem. It will activate at planing speeds should you attempt to steer the watercraft after releasing the throttle lever. The OTS system assists in turning by continuing to supply some thrust while the watercraft is decelerating, but you can turn more sharp- ly if you apply throttle while turning the han- dlebars.The OTS system does not function below planing speeds or when the engine is off. Once the engine slows down, the water- craft will no longer turn in response to han- dlebar input until you apply throttle again or you reach trolling speed.Practice turning in an open area without obstacles until you have a good feel for this maneuver.  This watercraft is water-jet propelled. The jet pump is directly connected to the en- gine. This means that jet thrust will produce some movement whenever the engine is running and the “F” (forward) or “R” (re- verse) shift indicator is displayed in the multifunction display. When the “N” (neu- tral) shift indicator is displayed, the forward and reverse thrust are balanced to help keep the watercraft from moving in eitherHazard information  Never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monoxide, a color- less, odorless gas that may cause loss of consciousness and death within a short time. Always operate the watercraft in an open area.  Do not touch the hot muffler or engine dur- ing or immediately after engine operation; they can cause serious burns.  Do not place magnets or objects with a strong magnetic force near the throttle le- ver or RiDE lever. The electronic throttle mechanism of the levers can be adversely affected, which could cause loss of control. In addition, do not place objects suscepti- ble to magnetic forces (i.e., credit cards, watches, etc.) close to the throttle lever or RiDE lever.Safety information16]]></page><page Index="24" isMAC="true"><![CDATA[Safety informationdirection, although some movement may occur.  Stop the engine and remove the clip from the engine shut-off switch before removing any debris or weeds, which may have col- lected around the jet intake.2111 “N” (Neutral position)  To avoid rear-end collisions while operat- ing the watercraft, check behind you be- fore using the RiDE lever to slow down or stop the watercraft. Make sure that there are no obstacles or people behind you be- fore shifting into reverse.  Keep away from the intake grate while the engine is on. Items such as long hair, loose clothing, or PFD straps can become entan- gled in moving parts, resulting in severe in- jury or drowning.  Never insert any object into the jet thrust nozzle while the engine is running. Severe injury or death could result from coming in contact with the rotating parts of the jet pump.1 Intake grate2 Jet thrust nozzle1 Clip2 Engine shut-off switch2 117]]></page><page Index="25" isMAC="true"><![CDATA[EJU30946Wakeboarding and water-skiingYou can use the watercraft for wakeboarding or water-skiing if it has the seating capacity to carry the operator, a rearward-facing spotter, and the wakeboarder or water-skier when he or she is not being pulled.The watercraft must also have a cleat de- signed to pull a ski rope; do not attach the rope to any other location.Safety informationNormal swimwear does not adequately protect against forceful water entry into the rectum or vagina. The person being pulled should wear a wetsuit bottom or clothing that provides equivalent protection.  A second person should be on board as a spotter to watch the wakeboarder or wa- ter-skier; in most states it is required by law. Let the person being pulled direct the operator’s control of speed and direction with hand signals.The spotter should sit astride the rear of the seat and hold onto the handgrip with both feet firmly on the floor of the footwell for proper balance while facing to the rear to watch the wakeboarder’s or water-skier’s hand signals and condition.1 Handgrip11 CleatIt is the watercraft operator’s responsibility to be alert to the safety of the wakeboarder or water-skier and others. Know and follow all state and local regulations in effect for the waters in which you will be operating.The operator should be comfortable carrying passengers before attempting to pull a wake- boarder or water-skier.The following are some important consider- ations for minimizing risks while pulling a wakeboarder or water-skier.  The wakeboarder or water-skier should wear an approved PFD, preferably a bright- ly colored one so boat operators can see the person being pulled.  The wakeboarder or water-skier should wear protective clothing. Severe internal in- juries can occur if water is forced into body cavities as a result of falling into the water.1 Handgrip  Your control while pulling a wakeboarder orwater-skier is affected by the wakeboard-118]]></page><page Index="26" isMAC="true"><![CDATA[Safety informationer’s or water-skier’s ability, as well as waterand weather conditions.  When preparing to pull a wakeboarder orwater-skier, operate the watercraft at the slowest possible speed until the watercraft is well away from the person being pulled and slack in the ski rope is taken up. Make sure that the rope is not looped around anything.After checking that the wakeboarder or wa- ter-skier is ready and that there is no traffic or other obstacles, apply enough throttle to raise the person.  Make smooth, wide turns. The watercraft is capable of very sharp turns, which could exceed the abilities of the wakeboarder or water-skier. Keep the person being towed at least 50 m (164 ft), about twice the dis- tance of a standard ski rope, away from any potential hazard.  The operators of boats and other water- craft may not be aware that you are pulling a wakeboarder or water-skier. Together with the spotter, pay attention to others around you and cruise at safe speeds.  Be alert to the hazard of the ski rope handle snapping back at the watercraft when the wakeboarder or water-skier falls or is un- able to get up.  Towing heavy or bulky objects other than wakeboarders or water-skiers, such as an- other boat or watercraft, can cause loss of steering control and create a hazardous condition. If you must tow another boat in an emergency situation, operate slowly and cautiously.EJU30962Rules of the RoadYour Yamaha watercraft is legally consid- ered a powerboat. Operation of the water- craft must be in accordance with the rules and regulations governing the waterway on which it is used.Just as there are rules that apply when you are driving on streets and highways, there are waterway rules that apply when you are oper- ating your watercraft. These rules are used internationally, and are also enforced by the United States Coast Guard and local agen- cies. You should be aware of these rules, and follow them whenever you encounter another vessel on the water.Several sets of rules prevail according to geographic location, but are all basically the same as the International Rules of the Road. The rules presented here in this owner’s/op- erator’s manual are condensed, and have been provided for your convenience only. Consult your local U.S. Coast Guard Auxiliary or Department of Motor Vehicles for a com- plete set of rules governing the waters in which you will be operating your watercraft. Steering and sailing rulesWhenever two vessels on the water meet one another, one vessel has the right-of-way; it is called the “stand-on” vessel. The vessel that does not have the right-of-way is called the “give-way” or “burdened” vessel. These rules determine which vessel has the right-of-way, and what each vessel should do.Stand-on vesselThe vessel with the right-of-way has the duty to continue its course and speed, except to avoid an immediate collision. When you maintain your direction and speed, the other vessel will be able to determine how best to avoid you.19]]></page><page Index="27" isMAC="true"><![CDATA[Give-way vesselThe vessel which does not have the right-of- way has the duty to take positive and timely action to stay out of the way of the stand-on vessel. Normally, you should not cross in front of the vessel with the right-of-way. You should slow down or change directions brief- ly and pass behind the other vessel. You should always move in such a way that the operator of the other vessel can see what you are doing.The General Prudential Rule regarding the right-of-way is that if a collision appears un- avoidable, neither boat has the right-of-way. Both boats must avoid the collision.In other words, follow the standard rules ex- cept when a collision will occur unless both vessels try to avoid each other. If that is the case, both vessels become give-way ves- sels.Rules when encountering vesselsThere are three main situations that you may encounter with other vessels which could lead to a collision unless the Steering Rules are followed:Meeting: you are approaching another vessel head-onCrossing: you are traveling across another vessel’s pathOvertaking: you are passing or being passed by another vesselIn the following illustration, your watercraft is in the center. You should give the right-of- way to any vessels shown in the white area (you are the give-way vessel). Any vessels in the shaded area must yield to you (they are the give-way vessels). Both you and theSafety informationmeeting vessel must alter course to avoid each other.MeetingIf you are meeting another power-driven ves- sel head on, and are close enough to run the risk of collision, neither of you has the right- of-way. Both of you should alter course to avoid an accident. You should keep the other vessel on your port (left) side. This rule does not apply if both of you will clear one another if you continue on your set course and speed.CrossingWhen two power-driven vessels are crossing each other’s path close enough to run the risk of collision, the vessel which has the other on the starboard (right) side must keep out of the way of the other. If the other vessel is on your starboard (right) side, you must keep out of its way; you are the give-way vessel. If the other vessel is on your port (left) side, remem- ber that you should maintain course and di-20]]></page><page Index="28" isMAC="true"><![CDATA[Safety informationrection, provided the other vessel gives you the right-of-way as it should.OvertakingIf you are passing another vessel, you are the give-way vessel. This means that the other vessel is expected to maintain its course and speed. You must stay out of its way until you are clear of it. Likewise, if another vessel is passing you, you should maintain your speed and direction so that the other vessel can steer itself around you.Other special situationsThere are three other rules you should be aware of when riding your watercraft around other vessels.Narrow channels and bendsWhen navigating in narrow channels, you should keep to the right when it is safe and practical to do so. If the operator of a power- driven vessel is preparing to go around a bend that may obstruct the view of other wa- ter vessels, the operator should sound a pro- longed blast of four to six seconds on the whistle. If another vessel is around the bend, it too should sound the whistle. Even if no re- ply is heard, however, the vessel should still proceed around the bend with caution. If you navigate such waters with your watercraft, you will need to carry a portable air horn, available from local marine supply stores.Fishing vessel right-of-wayAll vessels fishing with nets, lines, or trawls are considered to be “fishing vessels” under the International Rules. Vessels with trolling lines are not considered fishing vessels. Fish- ing vessels have the right-of-way regardless of position. Fishing vessels cannot, however, impede the passage of other vessels in nar- row channels.Sailing vessel right-of-waySailing vessels should normally be given the right-of-way. The exceptions to this are:(1) When the sailing vessel is overtaking thepower-driven vessel, the power-drivenvessel has the right-of-way.(2) Sailing vessels should keep clear of anyfishing vessel.(3) In a narrow channel, a sailing vesselshould not hamper the safe passage of a power-driven vessel that can navigate only in such a channel.Reading buoys and other markersThe waters of the United States are marked for safe navigation by the lateral system of buoyage. Simply put, buoys and markers have an arrangement of shapes, colors, num- bers, and lights to show which side of the buoy a boater should pass on when navigat- ing in a particular direction. The markings on these buoys are oriented from the perspec- tive of being entered from seaward (the boat- er is going towards the harbor). Red buoys are passed on your starboard (right) side when proceeding from open water into the harbor, and black buoys are to your port (left) side. An easy way to remember the meaning of the colors is the phrase “red right return- ing”. When navigating out of the harbor, your position with respect to the buoys should be reversed; red buoys should be to port and black buoys to starboard.21]]></page><page Index="29" isMAC="true"><![CDATA[Many bodies of water used by boaters are entirely within the boundaries of a particular state. The Uniform State Waterway Marking System has been devised for these waters. This system uses buoys and signs with dis- tinctive shapes and colors to show regulatorySafety informationor advisory information. These markers are white with black letters and orange borders. They signify speed zones, restricted areas, danger areas, and general information.22]]></page><page Index="30" isMAC="true"><![CDATA[Safety informationRemember, markings may vary by geograph- ic location. Always consult local boating au- thorities before riding your watercraft in unfamiliar waters.EJU30983To get more boating safetyinformationBe informed about boating safety. Additional publications and information can be obtained from many organizations, including the fol- lowing.United States Coast GuardConsumer Affairs Staff (G-BC)Office of Boating, Public, and Consumer Af- fairsU.S. Coast Guard Headquarters Washington, D.C. 20593-0001 http://www.uscgboating.org/Other sourcesYou can find local rules by contacting the Na- tional Association of State Boating Law Ad- ministrators, or your local Power Squadron. Watercraft Education and TrainingThe Online Boating Safety Course, available through the watercraft section of the yama- ha-motor.com website, is a free, 50 question learning course available to the public. Upon successful completion of 80 percent or bet- ter, the user can request a certificate of com- pletion by mail or can download one immediately. The Online Boating Safety Course, provided by the Boat/US Founda- tion, is approved by the National Association of State Boating Law Administrators (NASB- LA) and recognized by the United States Coast Guard. This course meets the educa- tion requirement for those states that recog- nize non-proctored, NASBLA-approved courses.Yamaha is the watercraft industry’s leading manufacturer to build awareness and sup- port for boating education. In 1997, Yamaha launched its GET W.E.T. (Watercraft Educa- tion and Training) initiative and has since reached out to over one million Americans promoting the benefits of boating education.23]]></page><page Index="31" isMAC="true"><![CDATA[Safety informationThe Online Boating Safety Course: http://www.boatus.org/EJU30992Enjoy your watercraftresponsiblyYou share the areas you enjoy when riding your watercraft with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, waters, and wildlife with respect and courte- sy.Whenever and wherever you ride, think of yourself as the guest of those around you. Remember, for example, that the sound of your watercraft may be music to you, but it could be just noise to others. And the exciting splash of your wake can make waves others won’t enjoy.Avoid riding close to shoreline homes and waterfowl nesting areas or other wildlife ar- eas, and keep a respectful distance from fish- ermen, other boats, swimmers, and populated beaches. When travel in areas like these is unavoidable, ride slowly and obey all laws.Proper maintenance is necessary to ensure that the exhaust emission and sound levels of your watercraft will continue to be within reg- ulated limits. You have the responsibility to make sure that the recommended mainte- nance in this owner’s/operator’s manual is carried out.Remember, pollution can be harmful to the environment. Do not refuel or add oil where a spill could cause damage to nature. Remove your watercraft from the water and move it away from the shoreline before refueling. Dis- pose of water and any fuel and oil residue in the engine compartment according to local regulations. And keep your surroundings pleasant for the people and wildlife that share the waterways: don’t litter.24]]></page><page Index="32" isMAC="true"><![CDATA[Safety informationWhen you ride responsibly, with respect and courtesy for others, you help ensure that our waterways stay open for the enjoyment of a variety of recreational opportunities.25]]></page><page Index="33" isMAC="true"><![CDATA[Trolling speedWatercraft glossary“Trolling” is the lowest maneuvering speed. You are applying little or no throttle. The water- craft is down in the water, and there is no wake.Sub-planing speed“Sub-planing” is a medium speed. The bow of the watercraft is slightly up from the water sur- face, but you are still traveling through the water. There is a wake.Planing speed“Planing” is a faster speed. The watercraft is more level and is skimming on top of the water. There is a wake.BowThe front end of the watercraft.SternThe rear end of the watercraft.StarboardThe right side of the watercraft when facing forward.PortThe left side of the watercraft when facing forward.Bilge waterWater that has collected in the engine compartment.Yamaha Engine Management System (YEMS)YEMS is an integrated, computerized management system that controls and adjusts ignition timing, fuel injection, engine diagnostics, and the off-throttle steering (OTS) system. Reverse with Intuitive Deceleration Electronics (RiDE)RiDE is an electronic system that controls the reverse, neutral, and deceleration operations of the watercraft.DescriptionEJU4333126]]></page><page Index="34" isMAC="true"><![CDATA[DescriptionEJU31012ExteriorLocation of main components234511067 891 Hood2 Fuel filler cap (page 56)3 Handlebar4 Front seat (page 49)5 Rear seat (page 49)6 Footwell7 Sponson8 Gunwale9 Cooling water pilot outlet (page 35)10 Bow eye (page 51)27]]></page><page Index="35" isMAC="true"><![CDATA[Description32 1456789541 Boarding platform2 Cleat (page 51)3 Handgrip (page 50)4 Stern eye (page 51)5 Stern drain plug (page 60) 6 Reverse gate (page 37)7 Jet thrust nozzle8 Ride plate9 Reboarding step (VXR) (page 50)10 Speed sensor 11 Intake grate101128]]></page><page Index="36" isMAC="true"><![CDATA[Description12345 9 10 9876 1211 131 RiDE lever (page 37)2 Start switch (page 33)3 Electric trim up switch (page 39)4 Engine shut-off switch (page 33)5 Clip (page 33)6 Engine shut-off cord (lanyard) (page 33) 7 Engine stop switch (page 33)8 Electric trim down switch (page 39)9 Rearview mirror10 Multifunction information center (page 43) 11 Throttle lever (page 34)12 Glove compartment (page 53)13 Remote control transmitter (page 31)29]]></page><page Index="37" isMAC="true"><![CDATA[Engine compartment1 Electrical box2 Spark plug/Spark plug cap/Ignition coil3 Engine oil filler cap (page 58)4 Removable watertight storage compart- ment (page 54)5 Air filter case6 Water separator (page 35)7 Fuel tank8 Dipstick9 Engine cover10 Battery (page 66)11 Flushing hose connector3245 6 7 8 9 10 111Description30]]></page><page Index="38" isMAC="true"><![CDATA[Control function operationEJU31026Watercraft control functionsEJU43910Remote control transmitterThe Yamaha Security System and Low RPM Mode settings can be selected by operating the remote control transmitter. (See page 32 for Yamaha Security System setting proce- dures and page 41 for Low RPM Mode acti- vation procedures.)1 Remote control transmitterSince the watercraft is programmed to rec- ognize the internal code from this transmitter only, the settings can only be selected with this transmitter.If you accidentally lose your remote control transmitter or if it is not operating properly, contact a Yamaha dealer.When operating the watercraft, always keep the transmitter with you, such as by storing itin the transmitter holder in the glove compart- ment, so that it is not lost.11 Transmitter holder ECJ00753NOTICE The remote control transmitter is not completely waterproof. Do not sub- merge the transmitter or operate it un- derwater. If the transmitter is submerged, dry it with a soft, dry cloth, and then check that it is operating prop- erly. If the transmitter is not operating properly, contact a Yamaha dealer. Keep the remote control transmitter away from high temperatures and do not place it in direct sunlight.Do not drop the remote control trans- mitter, subject it to strong shocks, or place any heavy items on it.Use a soft, dry cloth to clean the remote control transmitter. Do not use deter- gent, alcohol, or other chemicals.Do not attempt to disassemble the re- mote control transmitter yourself. Oth- erwise, the transmitter may not operate properly. If the transmitter needs a new battery, contact a Yamaha dealer. Refer to local hazardous waste regulations when disposing of transmitter batteries.    31This device complies with Part 15 of the FCC Rules. Operation is subject to the following]]></page><page Index="39" isMAC="true"><![CDATA[Control function operationtwo conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired oper- ation.ECJ00031NOTICENumber of beepsYamaha Security System mode“UN- LOCK” in- dicator lightLockGoes offUnlock (normal operation mode)Comes onUnlock (Low RPM Mode)Comes onChanges or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the remote control transmitter.EJU31385Yamaha Security SystemThe Yamaha Security System functions to help prevent unauthorized use or theft of the watercraft. The lock and unlock modes of the security system can be selected by operating the remote control transmitter that is included with this watercraft. The engine cannot be started if the lock mode of the security sys- tem is selected. The engine can only be start- ed if the unlock mode is selected. (See page 31 for information on the remote control transmitter.)TIP:The Yamaha Security System settings canonly be selected while the engine is stopped. EJU36776Yamaha Security System settingsThe Yamaha Security System settings will be confirmed by the number of beeps when the remote control transmitter is operated, and by the “UNLOCK” indicator light of the multi- function information center. (See page 43 for information on the multifunction information center.)TIP:  The beeper sounds two times for the nor- mal operation mode or three times for the Low RPM Mode. (See page 41 for Low RPM Mode activation procedures.)  If the remote control transmitter is operated while the multifunction information center is in the standby state, the center will per- form the initial operation, and then the set- ting is selected.To select the lock mode:Push the lock button on the remote control transmitter briefly. The beeper sounds once and the “UNLOCK” indicator light blinks once, then goes off. This indicates the lock mode is selected.21 Lock button2 “UNLOCK” indicator lightTo select the unlock mode:Push the “L-Mode” (unlock) button on the re- mote control transmitter briefly. The beeper sounds two or three times and the “UN-132]]></page><page Index="40" isMAC="true"><![CDATA[Control function operationLOCK” indicator light blinks two or three times, then comes on. This indicates the un- lock mode is selected.Insert the clip under the engine shut-off switch before starting the engine.1231 L-Mode21 “L-Mode” (unlock) button2 “UNLOCK” indicator light EJU31153Engine stop switch “  ”1 Engine shut-off switch2 Clip3 Engine shut-off cord (lanyard)The engine stop switch (red button) stops the engine when the switch is pushed.When the engine is not running, remove the clip from the engine shut-off switch to pre- vent accidental starting or unauthorized op- eration by children or others.11 Engine stop switch EJU31164Engine shut-off switch “ ”The engine shut-off switch automatically stops the engine when the clip, on the end of the engine shut-off cord (lanyard), is removed from the switch, such as if the operator falls off the watercraft.EJU42323Start switch “ ”ECJ01311NOTICEDo not run the engine over 4000 r/min on land. Also, do not run the engine for more than 15 seconds without supplying water, otherwise the engine could overheat.The start switch (green button) starts the en- gine when the switch is pushed.Release the start switch as soon as the en- gine starts to run. If the engine does not start33]]></page><page Index="41" isMAC="true"><![CDATA[in 5 seconds, release the start switch, wait 15 seconds, and then try again. NOTICE: Never push the start switch while the engine is running. Do not operate the start switch for more than 5 seconds, otherwise the battery will be discharged and the engine will not start. Also, the starter motor could be damaged. [ECJ01041]EJU31212Throttle leverThe throttle lever increases the engine speed when the lever is squeezed.Control function operation111 Start switchThe engine will not start under any of the fol- lowing conditions:  Lock mode of the Yamaha Security Systemhas been selected. (See page 32 for Yamaha Security System setting proce- dures.)  Clip is removed from the engine shut-off switch.  Throttle lever is squeezed.  Throttle lever is malfunctioning.  RiDE lever is squeezed.  RiDE lever is malfunctioning.1 Throttle leverThe throttle lever returns automatically to itsfully closed (idle) position when released. EJU43341RiDE leverWhen the RiDE lever is squeezed, the reversegate lowers and the watercraft starts moving in reverse. If the watercraft is moving forward, the watercraft gradually slows down until it stops, and then the watercraft starts moving in reverse.11 RiDE leverWhen the RiDE lever is released, it automati- cally returns to its fully closed (idle) position and the reverse gate moves to the neutral po- sition.34]]></page><page Index="42" isMAC="true"><![CDATA[Control function operationEJU31262Steering systemBy turning the handlebars in the direction you wish to travel, the angle of the jet thrust noz- zle is changed, and the direction of the water- craft is changed accordingly.in response to handlebar input until you applythrottle again or you reach trolling speed. EJU35975Cooling water pilot outletWhen the engine is running, some of the cooling water that is circulated in the engine is discharged from the cooling water pilot outlet.1211 Handlebar2 Jet thrust nozzleSince the strength of the jet thrust determines the speed and degree of a turn, throttle must always be applied when attempting a turn, except at trolling speed.This model is equipped with the Yamaha En- gine Management System (YEMS) that in- cludes an off-throttle steering (OTS) system. It will activate at planing speeds should you attempt to steer the watercraft after releasing the throttle lever. The OTS system assists in turning by continuing to supply some thrust while the watercraft is decelerating, but you can turn more sharply if you apply throttle while turning the handlebars. The OTS sys- tem does not function below planing speeds or when the engine is off. Once the engine slows down, the watercraft will no longer turn1 Cooling water pilot outletThere is a cooling water pilot outlet on the port (left) side of the watercraft. To check for proper operation of the cooling system, make sure that water is being discharged from the cooling water pilot outlet. If water is not being discharged from the outlet, stop the engine and check the jet intake for clogging. (See page 99 for information on the jet intake.)TIP:  It will take about 60 seconds for the water to reach the outlet after the engine is start- ed.  Water discharge may not be constant when the engine is running at idling speed. If this occurs, apply a little throttle to makesure that water discharges properly. EJU40323Water separatorThe water separator prevents water from en- tering the fuel tank by collecting any water that has entered the fuel tank breather hose if the watercraft was capsized.35]]></page><page Index="43" isMAC="true"><![CDATA[Control function operationIf water has collected in the water separator, drain it by loosening the drain screw.1 21 Water separator 2 Drain screwTo drain water from the water separator:(1) Place a drain pan or dry cloth under thewater separator.(2) Gradually loosen the drain screw to drainthe water. Catch the draining water in the drain pan or soak it up with the dry cloth so that it does not spill into the engine compartment. If any water spills into the watercraft, be sure to wipe it up with a dry cloth.(3) Securely tighten the drain screw until it stops.36]]></page><page Index="44" isMAC="true"><![CDATA[Watercraft operationEJU40013Watercraft operation functionsEJU43153Shift systemEWJ01773  Make sure that there are no obstacles or people behind you before shifting into reverse.  Do not touch the reverse gate while the RiDE lever is being operated, otherwise you could be pinched.  If the RiDE lever and throttle lever are being operated at the same time, do not release only the RiDE lever. Otherwise, the watercraft could accelerate more quickly than expected, which may lead to an accident.The RiDE lever and throttle lever can be oper- ated to change the forward or rearward movement of the watercraft only when the engine is running. When the RiDE lever is squeezed, the reverse gate lowers and de- flects the water jet being discharged from the jet thrust nozzle so that the watercraft moves in reverse or is in neutral. When the throttle le- ver is squeezed, the reverse gate rises and the watercraft moves forward.TIP:  This model is equipped with a function which limits the engine speed in reverse.  When the engine is started, the reversegate automatically moves to the neutral po-sition.To shift into reverse:(1) Release the throttle lever.(2) Squeeze the RiDE lever. The reversegate will lower, the engine speed will in- crease, the watercraft will start moving inreverse, and the “R” (reverse) shift indi- cator will be displayed.1WARNING1 RiDE lever121 Reverse gate2 Reverse position11 “R” (Reverse position)To shift into neutral from reverse:Release the RiDE lever. The reverse gate will automatically return to the neutral position37]]></page><page Index="45" isMAC="true"><![CDATA[and the “N” (neutral) shift indicator will be dis- played.Watercraft operationTo shift into forward:(1) Release the RiDE lever.(2) Squeeze the throttle lever. The reversegate will rise completely, the engine speed will increase, the watercraft will start moving forward, and the “F” (for- ward) shift indicator will be displayed.111 RiDE lever121 Reverse gate2 Neutral position1 Throttle lever121 Reverse gate2 Forward position11 “N” (Neutral position)TIP:Although the neutral position helps keep the watercraft from moving even when the en- gine is running, some movement may occur.11 “F” (Forward position)38]]></page><page Index="46" isMAC="true"><![CDATA[Watercraft operationTIP:If the RiDE lever is squeezed while the throttle lever is squeezed, the watercraft will slow down, and once stopped, move in reverse. To shift into neutral from forward:(1) Release the throttle lever.(2) Lightly squeeze and release the RiDE le-ver. The “N” (neutral) shift indicator will be displayed.can be operated only when the engine is run- ning.There are 5 positions: neutral, 2 bow-down positions (a) and (b), and 2 bow-up positions (c) and (d).121 Electric trim up switch2 Electric trim down switch(d)(c)(b)(a)(d) (c)(b) (a)11 “N” (Neutral position)TIP:If the RiDE lever is squeezed continuously,the reverse gate will move to the reverse po-sition.EJU43161Electric trim systemThe electric trim up switch and electric trim down switch are located at the left handlebar grip and are operated to change the vertical angle of the jet thrust nozzle, which adjusts the trim angle of the watercraft. The switchesBow-down positions (a) and (b)The bow will go down, causing the trim angle to decrease.39]]></page><page Index="47" isMAC="true"><![CDATA[Vertical movement of the bow will be reduced and the watercraft will get up on plane more quickly when accelerating.Bow-up positions (c) and (d)The bow will go up, causing the trim angle to increase.There is less water resistance, therefore, straight-ahead acceleration is enhanced.TIP:The watercraft performance characteristics according to the trim angle change depend- ing on the operating conditions.Watercraft operation(2) Push the electric trim up switch or elec- tric trim down switch to select the de- sired trim angle.12(d)(c) N (b)(a)To change the trim angle:(1) If the reverse gate is in the neutral posi-tion, lightly squeeze the throttle lever so that the watercraft moves forward.1 Electric trim up switch2 Electric trim down switchTIP:  When the reverse gate moves to the neutral or reverse position, the jet thrust nozzle will automatically return to the neutral position. When the reverse gate moves to the for- ward position, the jet thrust nozzle will au- tomatically change to the set trim angle.  When the engine stops, the jet thrust noz- zle returns to the neutral position.40]]></page><page Index="48" isMAC="true"><![CDATA[Watercraft operationEJU40001Watercraft operation modesEJU36787Low RPM ModeThe Low RPM Mode is a function that limits the maximum engine speed to approximately 70% of the maximum engine speed in the normal mode.The Low RPM Mode can only be activated and deactivated by operating the remote control transmitter that is included with this watercraft. (See page 31 for information on the remote control transmitter.)TIP:If the remote control transmitter is operated while the multifunction information center is in the standby state, the center performs the initial operation, and then the setting is se- lected.To activate the Low RPM Mode:Push the “L-Mode” (unlock) button on the re- mote control transmitter for more than 4 sec- onds. Once the beeper sounds three times and the “UNLOCK” indicator light blinks three times, then comes on, the “L-MODE” indicator light comes on and the Low RPM Mode is activated.TIP:If the Low RPM Mode is activated immediate-Number of beepsLow RPM Mode operation“L- MODE” indicator lightActivatedComes onDeactivatedGoes off1 Remote control transmitterly after the information display turns off, the TIP: “L-MODE” indicator light will not come on.The Low RPM Mode can only be activated when the engine is stopped in the unlock mode of the Yamaha Security System. Activating and deactivating the Low RPM ModeActivation of the Low RPM Mode will be con- firmed by the number of beeps when the re- mote control transmitter is operated, and by the “L-MODE” indicator light of the multifunc- tion information center. (See page 43 for in- formation on the multifunction information center.)41]]></page><page Index="49" isMAC="true"><![CDATA[The “L-MODE” indicator light will come on when the engine is started.1 “L-Mode” (unlock) buttonWatercraft operation1 L-Mode121 “UNLOCK” indicator light 2 “L-MODE” indicator lightTo deactivate the Low RPM Mode:Push the “L-Mode” (unlock) button on the re- mote control transmitter for more than 4 sec- onds. Once the beeper sounds two times and the “UNLOCK” indicator light blinks two times, then comes on, the “L-MODE” indica- tor light goes off and the Low RPM Mode is deactivated. When the Low RPM Mode is de- activated, the watercraft returns to the nor- mal operation mode.42]]></page><page Index="50" isMAC="true"><![CDATA[Instrument operationEJU43760Multifunction informationcenterThe multifunction information center displays various watercraft information.their state before the center turned off, andthen the center starts to operate normally. EJU35027Information displayThe information display shows watercraft op- erating conditions.12341234567891 “UNLOCK” indicator light 2 Information display3 “L-MODE” indicator light 4 “WARNING” indicator lightMultifunction information center initial op- erationWhen the multifunction information center is activated, all of the display segments come on. After 2 seconds, the warning indicators in the information display go off, and then the center starts to operate normally.If only the multifunction information center is activated, the “WARNING” indicator light blinks once.TIP:The “UNLOCK” indicator light also comes on as part of the initial operation.The “UNLOCK” indicator light will go off when the engine is started.Multifunction information center standby stateIf the multifunction information center does not receive any operation input within 25 sec- onds after the engine stops, the center will turn off and enter a standby state. When the engine is started again, the displays return to1 Trim indicator2 Tachometer3 Speedometer4 Oil pressure warning indicator5 Engine overheat warning indicator 6 Check engine warning indicator7 Shift indicator8 Fuel level warning indicator 9 Fuel level meterEJU43830SpeedometerThe speedometer shows the watercraft speed against water.By switching the display units, the speed can be shown in kilometers per hour “km/h” or miles per hour “MPH”.43]]></page><page Index="51" isMAC="true"><![CDATA[TIP:“MPH” is selected as the display unit at the Yamaha factory.Instrument operationcenter turns off. The speedometer display units change.To switch the speedometer display units again, repeat this procedure.111 SpeedometerTo switch the speedometer display units: Start the engine, stop the engine, and then push the engine stop switch for at least 4 seconds before the multifunction information1 Engine stop switch1 Speedometer EJU31464TachometerThe tachometer shows the engine speed.144]]></page><page Index="52" isMAC="true"><![CDATA[Instrument operationThe outer numbers × 1000 r/min and display (reverse). (See page 37 for shifting proce- segments on the meter show the engine dures.)speed.11 Tachometer EJU43890Shift indicatorThis indicator shows the reverse gate shift positions: “F” (forward), “N” (neutral), and “R”11 “F” (Forward position)11 “N” (Neutral position)4511 “R” (Reverse position) EJU44010Trim indicatorThis indicator shows the trim angle of the jet thrust nozzle. One of the two upper display segments will be shown when the trim angle is increased, and one of the two lower display segments will be shown when the trim angle]]></page><page Index="53" isMAC="true"><![CDATA[is decreased. When the neutral position of the jet thrust nozzle is selected, the middle display segment will be shown. (See page 39 for trim angle selection procedures.)Instrument operationwarning indicator, and the “WARNING” indi- cator light blink, and the buzzer sounds inter- mittently for 30 seconds.11 Trim indicator EJU31515Fuel level meterThe fuel level meter shows the amount of fuel remaining in the fuel tank. The amount of re- maining fuel is shown using eight display segments, which disappear two at a time as the fuel level decreases.TIP:The accuracy of the fuel level meter varies depending on the operating conditions. Use this function as a reference only.If the fuel level warning is activated, refill the fuel tank as soon as possible. (See page 56 for information on filling the fuel tank.)After the fuel tank is refilled, the warning sig- nals will be cleared when the engine is re-started.EJU43720Oil pressure warningIf the oil pressure drops significantly, the oil pressure warning indicator, the check engine warning indicator, and the “WARNING” indi- cator light blink, and the buzzer sounds inter- mittently for 30 seconds. At the same time, the maximum engine speed is limited.11 Fuel level meter EJU44020Fuel level warningIf the fuel remaining in the fuel tank drops to about 18 L (4.8 US gal, 4.0 Imp.gal), the low- est two fuel level segments, the fuel levelIf the oil pressure warning is activated, imme- diately reduce the engine speed, return to shore, and then check the engine oil level. (See page 58 for information on checking the46]]></page><page Index="54" isMAC="true"><![CDATA[Instrument operationengine oil level.) If the oil level is sufficient,have a Yamaha dealer check the watercraft. EJU43901Engine overheat warningIf the engine temperature rises significantly, the engine overheat warning indicator, the check engine warning indicator, and the “WARNING” indicator light blink, and the buzzer sounds intermittently. After 5 sec- onds, the engine overheat warning indicator and the “WARNING” indicator light stop blinking and remain on, and the buzzer sounds continuously. After 30 seconds, the buzzer stops. While the engine overheat warning is activated, the maximum engine speed is limited.higher speeds could result in severe en- gine damage. [ECJ00042]EJU43731Check engine warningIf a sensor malfunction or a short circuit is de- tected, the check engine warning indicator and the “WARNING” indicator light blink, and the buzzer sounds intermittently for 30 sec- onds.If the engine is stopped after the check en- gine warning is activated, the information dis- play will indicate an error code.If the engine overheat warning is activated, immediately reduce the engine speed, return to shore, and then make sure that water is being discharged from the cooling water pilot outlet while the engine is running. If there is no discharge of water, stop the engine, and then check the jet intake for clogging. (See page 99 for information on the jet intake.) NOTICE: If you cannot locate and correct the cause of the overheating, consult a Yamaha dealer. Continuing to operate atIf the check engine warning is activated, im- mediately reduce the engine speed, return to shore, and have a Yamaha dealer check theengine. EJU43740Hour meterThe hour meter shows the total number of hours that the engine has been running since the watercraft was new.47]]></page><page Index="55" isMAC="true"><![CDATA[TIP:The elapsed time will be kept even if the bat- tery terminals have been disconnected.1 Hour meterEJU43750VoltmeterThe voltmeter shows the battery voltage. When the battery voltage is normal, the volt- meter displays approximately 12 volts.If the battery voltage has dropped significant- ly, “LO” is displayed on the voltmeter. If the battery voltage has risen significantly, “HI” is displayed. If “LO” or “HI” is displayed, imme- diately return to shore and have a Yamaha dealer service the watercraft.Instrument operation111 Voltmeter48]]></page><page Index="56" isMAC="true"><![CDATA[Equipment operationEJU40334EJU42203SeatsEquipmentTo install the rear seat:(1) Insert the projections on the front of theseat into the stays on the deck.The front and rear seats are removable. Remove the seats to access the engine com- partment and removable watertight storage compartment.To remove the rear seat:(1) Pull the rear seat latch up, and then lift upthe rear of the seat.11 Seat latch(2) Pull the seat rearward and remove it.(2) Push the rear of the seat down to secure- ly lock it in place.To remove the front seat:(1) Remove the rear seat.(2) Pull the front seat latch up, and then liftup the rear of the seat.1491 Seat latch]]></page><page Index="57" isMAC="true"><![CDATA[(3) Pull the seat rearward and remove it.Equipment operationEJU31364HandgripThe handgrip is used when boarding the wa- tercraft from the water and when the spotter is facing rearward. WARNING! Do not use the handgrip to lift the watercraft. The handgrip is not designed to support the watercraft’s weight. If the handgrip breaks, the watercraft could fall, which could result in severe injury. [EWJ00022]1To install the front seat:(1) Insert the projection on the front of theseat into the stay on the deck.(2) Push the rear of the seat down to secure- ly lock it in place.1 HandgripEJU34865Reboarding step (VXR)The reboarding step is used to assist in re- boarding the watercraft from the water. When boarding the watercraft, push the re- boarding step down until it stops. The step returns automatically to its original position when released. WARNING! Do not use the reboarding step to lift the watercraft. The reboarding step is not designed to support the watercraft’s weight. If the reboarding(3) Securely install the rear seat in its original position.50]]></page><page Index="58" isMAC="true"><![CDATA[Equipment operation step breaks, the watercraft could fall,which could result in severe injury. [EWJ01212]towing it in an emergency. (See page 103 for information on towing the watercraft.)111 Reboarding step1 Bow eyeEJU34882Stern eyesThe stern eyes are used to attach a rope to the watercraft when transporting or mooring it.1ECJ00743NOTICEUse the reboarding step only to board the watercraft in the water. Do not use the re- boarding step for any other purpose. The watercraft can be damaged.1 Stern eyeEJU40422CleatThe cleat is used to attach a ski rope to the watercraft when pulling a wakeboarder or water-skier. WARNING! Do not use the cleat to lift the watercraft. The cleat is not designed to support the watercraft’s weight. If the cleat breaks, the watercraftEJU34873Bow eyeThe bow eye is used to attach a rope to the watercraft when transporting, mooring, or51]]></page><page Index="59" isMAC="true"><![CDATA[could fall, which could result in severe in- jury.[EWJ01511]Equipment operationTo open the bow storage compartment:Pull the hood latch up, and then lift up the rear of the hood.111 CleatEJU35147Storage compartmentsThis watercraft is equipped with the following storage compartments.Only the securely closed watertight storage compartment is waterproof. If you carry ob- jects that must be kept dry, put them in a wa- terproof bag.Make sure that the storage compartmentsare closed securely before operating the wa-tercraft.EJU43770Bow storage compartmentThe bow storage compartment is located un- der the hood.1 Hood latch11 Bow storage compartmentBow storage compartment: Capacity:72.0 L (19.0 US gal, 15.8 Imp.gal) Load limit:5.0 kg (11 lb)52]]></page><page Index="60" isMAC="true"><![CDATA[Equipment operationTo close the bow storage compartment: Return the hood to its original position, and then push the hood latch down to securely lock it in place.To open the glove compartment:Pull the glove compartment latch up, and then lift up the lid.1To drain water from the bow storage com- partment:(1) Remove the drain plug on the bottom ofthe storage compartment to drain the water into the engine compartment.531 Glove compartment latch111 Glove compartmentGlove compartment: Capacity:3.4 L (0.9 US gal, 0.7 Imp.gal) Load limit:1.5 kg (3 lb)1 Drain plug(2) Securely install the drain plug in its origi-nal position. EJU43781Glove compartmentThe glove compartment is located in front of the seat.]]></page><page Index="61" isMAC="true"><![CDATA[To close the glove compartment:Push the lid down to securely lock it in place.Equipment operation(2) Loosen the cap and remove it.1EJU37234Watertight storage compartmentThe watertight storage compartment is locat- ed under the rear seat.The compartment is watertight when the cap is closed securely.The watertight storage compartment is re- movable.To open the watertight storage compartment: (1) Remove the rear seat. (See page 49 forseat removal and installation proce- dures.)1 Watertight storage compartmentTo close the watertight storage compart- ment:(1) Securely install the cap by tightening ituntil it stops.(2) Securely install the rear seat in its originalposition. EJU43790Fire extinguisher holder and coverThe fire extinguisher holder and cover are lo- cated in the bow storage compartment.1 Watertight storage compartment cap1Watertight storage compartment: Capacity:5.8 L (1.5 US gal, 1.3 Imp.gal) Load limit:3.0 kg (7 lb)54]]></page><page Index="62" isMAC="true"><![CDATA[Equipment operationTo use the fire extinguisher holder and cover: (1) Pull the hood latch up, and then lift upthe rear of the hood.the hood is securely closed before using the watercraft.11 Hood latch(2) Unhook the band and remove the fire ex- tinguisher from the fire extinguisher cov- er.1 21 Band2 Fire extinguisher holder and cover(3) Place the fire extinguisher in the fire ex- tinguisher cover, and then securely fas- ten the fire extinguisher with the band.(4) Return the hood to its original position, and then push the hood latch down to securely lock it in place. Make sure that55]]></page><page Index="63" isMAC="true"><![CDATA[EJU31823Fuel requirements FuelGasohol containing ethanol can be used if ethanol content does not exceed 10% and the fuel meets the minimum octane ratings. E-85 is a fuel blend containing 85% ethanol and therefore must not be used in this water- craft. All ethanol blends containing more than 10% ethanol can cause fuel system damage or engine performance problems.Yamaha does not recommend gasohol con- taining methanol because it can cause fuel system damage and engine performance problems.To fill the fuel tank:(1) Before refueling, stop the engine. Do notstand or sit on the watercraft. Never refu- el while smoking, or while in the vicinity of sparks, open flames, or other sources of ignition.(2) Place the watercraft in a well-ventilated area and in a horizontal position.(3) Remove the seats, and then check the fuel level. (See page 49 for seat removal and installation procedures.)(4) Pull the hood latch up, and then lift up the rear of the hood.EJU43641 EWJ00283Operation and handling requirementsWARNING  Gasoline and gasoline vapors are ex- tremely flammable. To avoid fires and explosions and to reduce the risk of in- jury when refueling, follow these in- structions.  Gasoline is poisonous and can cause in- jury or death. Handle gasoline with care. Never siphon gasoline by mouth. If you should swallow some gasoline, inhale a lot of gasoline vapor, or get some gaso- line in your eyes, see your doctor imme- diately. If gasoline spills on your skin, wash with soap and water. If gasoline spills on your clothing, change your clothes.ECJ00322NOTICE  Do not use leaded gasoline. Leaded gasoline can seriously damage the en- gine.  Avoid getting water and contaminants in the fuel tank. Contaminated fuel can cause poor performance and engine damage. Use only fresh gasoline that has been stored in clean containers.GasoholThere are two types of gasohol: gasohol con- taining ethanol and that containing methanol.1 Hood latch1Recommended fuel:Regular unleaded gasoline with a minimum octane rating of86(Pump octane number) = (R + M)/290 (Research octane number)56]]></page><page Index="64" isMAC="true"><![CDATA[Operation and handling requirements(5) Loosen the fuel filler cap and remove it.Do not leave the watercraft with a full tank in direct sunlight.1121 Fuel filler cap(6) Slowly add fuel to the fuel tank.1 Top of the fuel tank2 Approximately 50 mm (2 in) from top of thefuel tank12(7) Stop filling when the fuel level reaches approximately 50 mm (2 in) from the top of the fuel tank. Do not overfill the fuel tank. Because fuel expands when it heats up, heat from the engine or the sun can cause fuel to spill out of the fuel tank.1 Top of the fuel tank2 Approximately 50 mm (2 in) from top of thefuel tank(8) Wipe up any spilled fuel immediately with a dry cloth.(9) Securely install the fuel filler cap by tight- ening it until it clicks.(10) Return the hood to its original position, and then push the hood latch down to securely lock it in place. Make sure that the fuel filler cap and the hood are se-57Fuel tank capacity:70 L (18.5 US gal, 15.4 Imp.gal)]]></page><page Index="65" isMAC="true"><![CDATA[Operation and handling requirementscurely closed before using the water- craft.EJU40291Engine oil requirementsEJU31897Engine oilECJ00282NOTICEUse only 4-stroke engine oil. Usage of 2- stroke engine oil could result in severe en- gine damage.Recommended engine oil: YAMALUBE 4WRecommended engine oil type: SAE 10W-30, 10W-40, 20W-40, 20W-50Recommended engine oil grade: API SE,SF,SG,SH,SJ,SL(11) Securely install the seats in their original positions.TIP:When the engine is operated at high speeds, some engine oil may be consumed. Be sure to check the engine oil level.Checking the engine oil levelEWJ00341Engine oil is extremely hot immediately af- ter the engine is turned off. Coming in con- tact with or getting any engine oil on your clothes could result in burns.ECJ01002NOTICEMake sure that debris and water do not enter the oil filler hole. Debris and water in the engine oil can cause serious engine damage.To check the engine oil level:(1) Place the watercraft in a precisely levelposition on land with the engine stopped. If the engine was running, allow the engine oil to settle by waiting 5 min- utes or more before checking the oil lev- el.WARNING58]]></page><page Index="66" isMAC="true"><![CDATA[Operation and handling requirements(2) Remove the seats. (See page 49 for seat removal and installation procedures.)(3) Remove the dipstick and wipe it clean.(6) Loosen the engine oil filler cap and re- move it.111 Dipstick1 Engine oil filler cap(7) Slowly add engine oil.TIP:The difference between the minimum and maximum level marks on the dipstick is equal to approximately 1 L (1.06 US qt, 0.88 Imp.qt) of engine oil.(8) Wait approximately 5 minutes to allow the engine oil to settle, and then check the engine oil level again.(9) Repeat steps 3–8 until the engine oil is at the proper level.(10) Securely install the engine oil filler cap by tightening it until it stops.(11) Securely install the seats in their original positions.(4) Insert the dipstick back into the dipstick tube completely. Remove the dipstick again and make sure that the engine oil level is between the minimum and maxi- mum level marks.1 21 Maximum level mark2 Minimum level mark(5) If the engine oil level is significantly above the maximum level mark, consult a Yamaha dealer. If the engine oil level is below the minimum level mark, add en- gine oil.59]]></page><page Index="67" isMAC="true"><![CDATA[Operation and handling requirementsEJU40022Draining the bilge waterECJ01302NOTICEDo not run the engine at full throttle when bilge water remains in the engine com- partment. The bilge water can splash into the engine, which can result in severe damage.EJU40035Draining the bilge water on landTo drain the bilge water on land:(1) Loosen the stern drain plugs and removethem.maining moisture in the engine compart-ment with a dry cloth.(4) Securely install the stern drain plugs bytightening them until they stop. NOTICE: Before installing the stern drain plugs, clean the drain plug threads and the O-rings on the plugs to remove any foreign materials, such as dirt or sand. Otherwise, the stern drain plugs could be damaged, allowing water to enter the engine compartment. Check the O-rings on the stern drain plugs and make sure that the plugs are tightened securely before launching the water- craft. Otherwise, water may flood the engine compartment and cause thewatercraft to submerge. [ECJ00363] EJU40535Draining the bilge water on waterA small quantity of bilge water will remain in the engine compartment even after the bilge water is drained on water. To completely drain the bilge water, remove the watercraft from the water and drain the bilge water on land.Jet vacuum bilge draining systemWhile the watercraft is operating, bilge water in the engine compartment is drawn in by the vacuum that is generated in the jet pump and discharged from the watercraft through the jet thrust nozzle.To drain the bilge water on water:Operate the watercraft as straight as possible and above planing speed for at least 2 min- utes. NOTICE: Do not run the engine at full throttle for at least 1 minute after the en- gine has been restarted. Bilge water in the engine compartment can splash into the11 Stern drain plug(2) Raise the bow of the watercraft, such as by placing the watercraft on a slope, to drain the bilge water from the engine compartment.(3) After the bilge water has drained from the stern drain plug holes, wipe up any re-60]]></page><page Index="68" isMAC="true"><![CDATA[Operation and handling requirementsengine, which can result in severe dam- age. [ECJ00554]EJU42432Transporting on a trailerWhen transporting the watercraft on a trailer, secure the tie downs to the trailer through the bow eye and stern eyes. NOTICE: Do not at- tach ropes or tie downs to any part of the watercraft other than the bow eye and stern eyes to secure the watercraft to the trailer. Otherwise, the watercraft may be damaged. Wrap the ropes or tie downs with towels or rags where they touch the body of the watercraft to avoid scratches or damage. [ECJ02150]61]]></page><page Index="69" isMAC="true"><![CDATA[EJU36666Engine break-inNOTICEFailure to perform the engine break-in could result in reduced engine life or even severe engine damage.The engine break-in is essential to allow the various components of the engine to wear and polish themselves to the correct operat- ing clearances. This ensures proper perfor- mance and promotes longer component life. To perform the engine break-in:(1) Check the engine oil level. (See page 58 for information on checking the engine oil level.)(2) Launch the watercraft and start the en- gine. (See page 75 for information on starting the engine.)(3) For the first 5 minutes, operate with the engine speed at 2000 r/min.(4) For the next 30 minutes, operate with the engine speed below 5000 r/min.(5) For the next 1 hour, operate with the en- gine speed below 6000 r/min.After the engine break-in is complete, the wa- tercraft can be operated normally.ECJ00432First-time operation62]]></page><page Index="70" isMAC="true"><![CDATA[Pre-operation checksEJU31982EWJ00412Failure to inspect or maintain the watercraft properly increases the possibility of an ac- cident or damage to the watercraft. Do not operate the watercraft if you find any prob- lem. If a problem cannot be corrected by the procedures provided in this manual, have the watercraft inspected by a Yamaha dealer.EJU41234Pre-operation checklistBefore using this watercraft, be sure to perform the checks in the following checklist.WARNINGITEMROUTINEPAGEPRE-LAUNCH CHECKSEngine compartmentVentilate the engine compartment.Check inside the engine compartment for damage.65Fuel systemCheck the fuel system for leakage. Check the fuel level in the fuel tank.65Water separatorCheck the water separator for water.65Engine unitCheck the exterior of the engine unit for damage.66Engine oil levelCheck the engine oil level.66Bilge waterCheck the engine compartment for bilge water.66BatteryCheck the battery connections and electrolyte level.66Steering systemCheck the steering system for proper operation.67RiDE leverCheck the RiDE lever for proper operation.68Throttle leverCheck the throttle lever for proper operation.68Remote control transmitterCheck the remote control transmitter for proper op- eration.68Engine shut-off cord (lan- yard)Check the engine shut-off cord (lanyard) for dam- age.68SwitchesCheck the start switch, engine stop switch, and en- gine shut-off switch for proper operation.69Storage compartmentsCheck the storage compartments for damage and water.69Fire extinguisher holder, cover, and bandCheck the fire extinguisher holder, cover, and band for damage.69Fire extinguisherCheck the condition of the fire extinguisher.70Safety equipmentCheck that safety equipment meeting the applica- ble regulations is on board.70Hull and deckCheck the hull and deck for damage.70Jet intakeCheck the jet intake for damage and clogging.70Jet thrust nozzle and re- verse gateCheck the jet thrust nozzle and reverse gate for damage.70Stern drain plugsCheck the stern drain plugs for damage and foreign material and check that they are securely installed.7063]]></page><page Index="71" isMAC="true"><![CDATA[Pre-operation checksITEMROUTINEPAGEHoodCheck that the hood is securely closed.71Front and rear seatsCheck that the seats are securely installed.49POST-LAUNCH CHECKSCooling water pilot outletCheck that water is discharged from the cooling water pilot outlet while the engine is running.71Multifunction information centerCheck the multifunction information center for prop- er operation.71Shift systemCheck the shift system for proper operation.72Trim indicatorCheck the trim indicator for proper operation.72Engine idling speedCheck the engine idling speed.73TIP:To ensure safety and reliability, pre-operation checks should be made each time the water- craft is used.64]]></page><page Index="72" isMAC="true"><![CDATA[Pre-operation checksEJU32282Pre-operation check pointsEJU42382Pre-launch checksPerform the pre-launch checks in the pre-op- eration checklist while the watercraft is on land.To perform the pre-launch checks:(1) Remove the seats and removable water- tight storage compartment. (See page 49 for seat removal and installation proce- dures and page 54 for information on the removable watertight storage compart- ment.)(2) Perform the checks and make sure that there are no malfunctioning items or oth- er problems.(3) After completing these checks, securely install the removable watertight storage compartment and seats in their originalpositions.EJU32334Engine compartment checkEWJ00462Failure to ventilate the engine compart- ment could result in a fire or explosion. Do not start the engine if there is a fuel leak.Ventilatetheenginecompartment.Leavethe engine compartment open for a few minutes to allow any fuel vapors to escape.Make sure that there is no damage inside the engine compartment.EJU34215Fuel system checksEWJ00382Leaking fuel can result in fire or explosion.  Check for fuel leakage regularly.  If any fuel leakage is found, the fuel sys-tem must be repaired by a qualified me- chanic. Improper repairs can make the watercraft unsafe to operate.Make sure that there is no damage, leakage, or other problem in the fuel system.Check:  Fuel filler cap and seal for damage  Fuel tank for damage and leakage  Fuelhosesandjointsfordamageandleak-age  Fuel tank breather hose for damage andleakage EJU36875Fuel level checkCheck the fuel level in the fuel tank.Add fuel if necessary. (See page 56 for infor-mation on filling the fuel tank.) EJU32424Water separator checkMake sure that no water has collected in the water separator. If water has collected in theWARNINGWARNING65]]></page><page Index="73" isMAC="true"><![CDATA[water separator, drain it. (See page 35 for in- formation on draining the water separator.)Pre-operation checksthe dipstick. (See page 58 for information on checking the engine oil level.)111 Water separator EJU40182Engine unit checkCheck the exterior of the engine unit for dam-age or other problem. EJU36886Engine oil level checkMake sure that the engine oil level is between the minimum and maximum level marks on1 Dipstick1 21 Maximum level mark 2 Minimum level markEJU32456Bilge water checkMake sure that no bilge water has collected in the engine compartment. If bilge water has collected in the engine compartment, drain it. (See page 60 for information on draining thebilge water.) EJU32485Battery checksMake sure that the battery terminals and breather hose are not damaged and that the battery leads and breather hose are connect- ed properly. WARNING! Fire or explosion could result if the breather hose is dam-66]]></page><page Index="74" isMAC="true"><![CDATA[Pre-operation checks aged, obstructed, or not connected prop-whole range, and that the free play is not ex- cessive.erly. [EWJ00452] 131 Negative (–) battery terminal: Black lead 2 Positive (+) battery terminal: Red lead3 Breather hoseMake sure that the electrolyte level is be- tween the minimum and maximum level marks. WARNING! Never operate the wa- tercraft if the battery does not have suffi- cient power to start the engine or if it shows any other signs of decreased pow- er. Loss of battery power may leave you stranded. [EWJ01241]1 Maximum level mark 2 Minimum level markMake sure that the battery is securely held inplace.EJU32614Steering system checksTurn the handlebars to the right and left sev- eral times to make sure that operation is smooth and unrestricted throughout the267Turn the handlebars as far as possible to the right and left to make sure that the jet thrust nozzle moves as the handlebars are turned, and that there is no difference between the]]></page><page Index="75" isMAC="true"><![CDATA[right and left fully turned positions of the jet thrust nozzle.Pre-operation checkslever returns automatically to its fully closed position when released.Difference between fully turned posi- tions of jet thrust nozzle (distances A and B):Maximum 5 mm (0.20 in)EJU43212RiDE lever checksOperate the RiDE lever several times to make sure that operation is smooth throughout the whole range. Also, make sure that the RiDEEJU40113Remote control transmitter checkMake sure that the remote control transmitter operates properly. (See page 32 for Yamaha Security System setting procedures and page 41 for Low RPM Mode activation pro-cedures.)EJU32664Engine shut-off cord (lanyard) checkMake sure that the engine shut-off cord (lan- yard) is not damaged. If the cord is damaged, replace it. WARNING! Never try to repair the engine shut-off cord (lanyard) or tie it together. The engine shut-off cord (lan-EJU42181Throttle lever checksOperate the throttle lever several times to make sure that operation is smooth through- out the whole range. Also, make sure that the throttle lever returns automatically to its fully closed (idle) position when released.68]]></page><page Index="76" isMAC="true"><![CDATA[Pre-operation checksyard) may not pull free when the operator falls off, allowing the watercraft to contin- ue to run and cause an accident. [EWJ01221]EJU32676Switch checksECJ01311NOTICEDo not run the engine over 4000 r/min on land. Also, do not run the engine for more than 15 seconds without supplying water, otherwise the engine could overheat.Check the start switch, the engine stop switch, and the engine shut-off switch for proper operation. (See pages 33 to 33 for in- formation on operating each switch.)To check the operation of the switches:(1) If the lock mode is selected for the Yamaha Security System setting, select the unlock mode. (See page 32 for Yamaha Security System setting proce-dures.)(2) Push the start switch to make sure thatthe engine starts.(3) As soon as the engine starts running,push the engine stop switch to makesure that the engine stops immediately. (4) Restart the engine, and then pull the en- gine shut-off cord (lanyard) to remove the clip from the engine shut-off switch to make sure that the engine stops im-mediately. EJU40102Storage compartment checksMake sure that the storage compartments are not damaged and that water has not col- lected in the compartments. (See page 52 forinformation on the storage compartments.) EJU43800Fire extinguisher holder, cover, and bandchecksMake sure that the fire extinguisher holder, cover, and band are not damaged and that the fire extinguisher is securely held in place using the band. (See page 54 for information on the fire extinguisher holder, cover, and band.)12345691 Clip2 Engine shut-off switch3 Start switch4 Engine stop switch5 Engine shut-off cord (lanyard)]]></page><page Index="77" isMAC="true"><![CDATA[EJU32534Fire extinguisher checkCheck that there is a full fire extinguisher onPre-operation checkstake is clogged, clean it. (See page 99 for in-formation on the jet intake.)EJU43220board. Jet thrust nozzle and reverse gate checkTo check the fire extinguisher, see the in- structions supplied by the fire extinguisher manufacturer. Always keep the fire extin- guisher secured in the holder with its cover in place.Always carry a fire extinguisher on board. A fire extinguisher is not standard equipment with this watercraft. If you do not have one, contact a Yamaha dealer or a fire extinguish- er dealer to obtain one meeting the proper specifications.EJU40122Safety equipment checkCheck that safety equipment meeting the ap-plicable regulations is on board. EJU32353Hull and deck checkCheck the hull and deck for damage or otherproblem.EJU32657Jet intake checksMake sure that the jet intake is not damaged or clogged with weeds or debris. If the jet in-Check the jet thrust nozzle and reverse gatefor damage or other problem. EJU32477Stern drain plug checksLoosen the stern drain plugs and remove them, and then make sure that the plugs and O-rings on the plugs are not damaged and that there is no foreign material on the threads or O-rings on the plugs. NOTICE: Before installing the stern drain plugs, clean the drain plug threads and the O- rings on the plugs to remove any foreign materials, such as dirt or sand. Otherwise, the stern drain plugs could be damaged, allowing water to enter the engine com- partment. Check the O-rings on the stern drain plugs and make sure that the plugs are tightened securely before launching the watercraft. Otherwise, water may flood the engine compartment and cause the watercraft to submerge. [ECJ00363]Fire extinguisher: Classification:B-1 Capacity:2 lb or more70]]></page><page Index="78" isMAC="true"><![CDATA[Pre-operation checksSecurely install the stern drain plugs by tight- ening them until they stop.EJU40146Post-launch checksPerform the post-launch checks in the pre- operation checklist while the watercraft is in the water and the engine is running.To perform the post-launch checks:(1) Launch the watercraft. (See page 75 for information on launching the watercraft.)(2) Perform the checks and make sure that there are no malfunctioning items or oth-er problems.EJU40553Cooling water pilot outlet checkMake sure that water is discharged from the cooling water pilot outlet while the engine is running. (See page 35 for information on the cooling water pilot outlet.)2 11 Stern drain plug 2 O-ringEJU43810Hood checkPush down the hood latch and make sure that it is securely closed.EJU32715Multifunction information center checkMake sure that the multifunction information center operates properly. (See page 43 for in- formation on proper operation of the multi- function information center.)71]]></page><page Index="79" isMAC="true"><![CDATA[EJU43391Shift system checkOperate the throttle lever and RiDE lever, and check that the watercraft moves or does not move according to the displayed shift indica- tor. (See page 37 for shift system operation procedures.) WARNING! To avoid colli- sions, operate at safe speeds and keep aPre-operation checks safe distance away from people, objects,and other watercraft. [EWJ01860]11 “F” (Forward position)11 “N” (Neutral position)11 “R” (Reverse position) EJU43400Trim indicator checkOperate the electric trim switches and check that the trim indicator shows the correct trim72]]></page><page Index="80" isMAC="true"><![CDATA[Pre-operation checksangle of the jet thrust nozzle. (See page 39 for electric trim system operation procedures.)11 Trim indicator EJU40172Engine idling speed checkStart the engine and warm it up. Use the ta- chometer in the multifunction information center to make sure that the engine idling speed is not significantly above or below the specified range.73Engine idling speed: 1300 ±100 r/min]]></page><page Index="81" isMAC="true"><![CDATA[OperationEJU32903Operating your watercraftEWJ00511Before operating your watercraft, become familiar with all of the controls. Consult a Yamaha dealer about any control or func- tion that you do not fully understand. Fail- ure to understand how the controls work could cause an accident or prevent you from avoiding an accident.EJU32956Getting to know your watercraftOperating your watercraft requires skills ac- quired through practice over a period of time. Take the time to learn the basic techniques well before attempting more difficult maneu- vers.Operating your new watercraft can be a very enjoyable activity, providing you with hours of pleasure. However, it is essential to familiar- ize yourself with the operation of the water- craft to achieve the skill level necessary to enjoy riding safely.Before operating this watercraft, read this owner’s/operator’s manual, the Riding Prac- tice Guide, the Riding Instruction card, and all labels on the watercraft. Pay particular atten- tion to the safety information beginning on page 10. Also, watch the Basic Orientation Video provided with your watercraft. These materials should give you an understanding of the watercraft and its operation. Remember: This watercraft is designed to carry the operator and up to 2 passengers. Never exceed the maximum load limit or al- low more than 3 persons (or 2 persons if a wakeboarder or water-skier is being pulled) to ride the watercraft at any time.EJU32996Learning to operate your watercraftBefore operating the watercraft, always per- form the pre-operation checks listed on page 63. The short time spent checking the water- craft will reward you with added safety and reliability.Check state and local laws before operating your watercraft.Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft. Select a wide area to learn in, where there is good visibility and light boat traffic.Use the buddy system—operate with some- one nearby. Scan constantly for people, ob- jects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others.You should grip the handlebars firmly and keep both feet on the floor of the footwell. Do not attempt to ride with passengers until your operating skills are fully developed.Maximum load:240 kg (530 lb)Load is the total weight of cargo, op- erator, and passengers.WARNING74]]></page><page Index="82" isMAC="true"><![CDATA[OperationEJU40212Riding positionOperator riding positionThe operator should grip the handlebars firm- ly with both hands and sit astride the seat with both feet on the floor of the footwell.EJU36346Starting the engine on waterEWJ01531Do not apply throttle when anyone is at the rear of the watercraft. Turn the engine off or keep it at idle. Water and debris exiting the jet thrust nozzle can cause severe in- jury.To start the engine:(1) If the lock mode is selected for theYamaha Security System setting, select the unlock mode. (See page 32 for Yamaha Security System setting proce- dures.)(2) Move the watercraft to an area that is free from weeds and debris, and has a water depth of at least 60 cm (2 ft) from the bottom of the watercraft. NOTICE: Never run the engine in water that is less than 60 cm (2 ft) deep from the bottom of the watercraft, otherwise pebbles or sand could be sucked into the jet intake, causing impeller dam- age and engine overheating. [ECJ00473](3) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch. (See page 33 for information on operating the en- gine shut-off switch.) WARNING! Check that the engine shut-off cord (lanyard)WARNINGPassenger riding positionThe passenger(s) should hold on firmly, either to the person in front of them or to the hand- grip provided, and sit astride the seat with their feet on the floor of the footwell. Never al- low a passenger to ride in front of the opera- tor. (See page 18 for information on the riding position when pulling a wakeboarder or wa- ter-skier.)EJU32803Launching the watercraftWhen launching the watercraft, make sure that there are no obstacles around you.If the watercraft is launched from a trailer, someone should make sure that waves do not push the watercraft into the trailer.75]]></page><page Index="83" isMAC="true"><![CDATA[is attached correctly. If the engine shut-off cord (lanyard) is not attached correctly, it may not pull free when the operator falls off, allowing the water- craft to continue to run and cause an accident. [EWJ00582]Operation to avoid. A collision could result in severeinjury or death. [EWJ00602]1231 Clip2 Engine shut-off switch3 Engine shut-off cord (lanyard)(4) With the throttle lever released, push the start switch (green button) to start the engine. (See page 33 for information on operating the start switch.)EJU32873Leaving the watercraftIf leaving the watercraft, remove the clip from the engine shut-off switch to prevent acci- dental starting or unauthorized operation by children or others.EJU32863Stopping the engineRelease the throttle lever, and then push the engine stop switch (red button) to stop the engine. WARNING! You need throttle to steer. Shutting the engine off can cause you to hit an obstacle you are attemptingEJU43410Operating the watercraftWhen the throttle lever is squeezed, the “F” (forward) shift indicator will be displayed in the multifunction display and the watercraft will move forward. While the “F” (forward) shift indicator is displayed, the watercraft will move forward at trolling speed even if the throttle lever is in the fully closed (idle) posi-76]]></page><page Index="84" isMAC="true"><![CDATA[Operationtion. (See page 37 for shift system operation procedures.)Steering control depends on the combination of handlebar position and the amount of throttle.Water sucked in through the intake grate is pressurized by the impeller in the jet pump. As the pressurized water is expelled from the pump through the jet thrust nozzle, it creates thrust to move and steer the watercraft. The higher the engine speed, the more thrust pro- duced.The amount of jet thrust, in addition to the po- sition of the handlebars, determines how sharply you turn.A. More throttle produces higher thrust, sothe watercraft will turn more sharply.B. Less throttle produces lower thrust, so the watercraft will turn more gradually.C. Releasing the throttle lever completely produces only minimum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to11 “F” (Forward position)EJU43421Turning the watercraftEWJ01781  Do not release the throttle lever when trying to steer away from objects—you need throttle to steer. A collision could result in severe injury or death.  When operating at higher speeds, make gradual turns or slow down before turn- ing. Sharp high-speed turns may cause the watercraft to slide sideways or spin, throwing the operator and passenger(s) overboard, which could cause an injury.  Take early action to avoid collisions. The RiDE system is not a braking device for avoiding dangerous situations.WARNING77]]></page><page Index="85" isMAC="true"><![CDATA[steer without throttle. You may still have some turning ability immediately after re- leasing the throttle lever, but once the engine slows down, the watercraft will no longer respond to handlebar input until you apply throttle again or you reach trolling speed.At trolling speed, the watercraft can be turned gradually by handlebar position alone using just the amount of thrust available at idle.D. If the engine is stopped while riding, there is no thrust. The watercraft will go straight even though the handlebars are turned.You need throttle to steer.E. If the RiDE lever is squeezed and the handlebars are turned when the water- craft is cruising at planing speed, the wa-Operationtercraft will turn gradually while slowing down.1 Reverse gateThis model is equipped with the Yamaha En- gine Management System (YEMS) that in- cludes an off-throttle steering (OTS) system. It will activate at planing speeds should you attempt to steer the watercraft after releasing the throttle lever (see condition C above). The OTS system assists in turning by con- tinuing to supply some thrust while the water- craft is decelerating, but you can turn more sharply if you apply throttle while turning the handlebars. The OTS system does not func- tion below planing speeds or when the en- gine is off. Once the engine slows down, the watercraft will no longer turn in response to handlebar input until you apply throttle againor you reach trolling speed.EJU43251Stopping the watercraftThe watercraft is not equipped with a sepa-rate braking system. The watercraft slows down by water resistance or, when operating in reverse, by the water jet. The watercraft slows down as soon as the throttle lever is re- leased, but will coast for a distance before fully stopping. If you are not sure you can stop in time before hitting an obstacle, apply throttle and turn in another direction.From full speed, the watercraft comes to a complete stop due to water resistance in ap-E178]]></page><page Index="86" isMAC="true"><![CDATA[Operationproximately 110 m (360 ft) after the throttle le- ver is released or the engine is stopped, although this distance will vary depending on many factors, including gross weight, water surface conditions, and wind direction.If the RiDE lever is squeezed to slow down,the stopping distance is approximately 30%shorter than when the RiDE lever is not used.However, this distance will vary dependingon many factors, including gross weight, wa-ter surface conditions, and wind direction. EWJ01791  Allow adequate stopping distance.  Take early action to avoid collisions. Re- member, watercraft and other boats donot have brakes.  Operate defensively at safe speeds andkeep a safe distance away from people, objects, and other watercraft to give you time to stop.  Do not shut the engine off when slowing down in case you need engine power to steer away from a boat or other obstacle that comes into your path.  To avoid rear-end collisions while oper- ating the watercraft, check behind you before using the RiDE lever to slow down or stop the watercraft.EJU43441Operating the watercraft in reverse or neutralOperating in reverseWhen the RiDE lever is squeezed, the “R” (re- verse) shift indicator will be displayed in the multifunction display and the watercraft will move in reverse. (See page 37 for shift sys- tem operation procedures.)110 m (360 ft)11 “R” (Reverse position)WARNING79Make sure that there are no obstacles or peo- ple behind you before shifting into reverse.TIP:This model is equipped with a function which limits the engine speed in reverse. Operating in neutralWhen the RiDE lever is squeezed lightly and released, the “N” (neutral) shift indicator will be displayed in the multifunction display and the watercraft will stop in its current location.]]></page><page Index="87" isMAC="true"><![CDATA[(See page 37 for shift system operation pro- cedures.)OperationNOTICE: Never run the engine in water that is less than 60 cm (2 ft) deep from the bottom of the watercraft, otherwise peb- bles or sand could be sucked into the jet intake, causing impeller damage and en- gine overheating. [ECJ00473]TIP:VXR: This watercraft is equipped with a re- boarding step, which can be lowered and used to assist in reboarding. (See page 50 for information on operating the reboardingstep.)EJU36354Boarding alone(1) From the rear of the watercraft, place both hands on the boarding platform, pull yourself up, and then grasp the handgrip with one hand.60 cm (2 ft)11 “N” (Neutral position)TIP:This model is equipped with a function whichlimits the engine speed in neutral. EJU36087Boarding the watercraft EWJ01112Be sure the operator and any passengers have practiced boarding from the water while still close to shore before riding. A person who has made many unsuccessful attempts to get back on the watercraft may become fatigued and suffer from ex- posure, increasing the risk of injury and drowning.Board the watercraft in water free from weeds and debris and at least 60 cm (2 ft) deep from the bottom of the watercraft.WARNING80]]></page><page Index="88" isMAC="true"><![CDATA[Operation(2) Pull yourself up to a kneeling position on the boarding platform, and then move to the seat and sit astride.holding on to the person in front of themor to the handgrip provided.  Before boarding the watercraft, makesure that the engine is stopped. If the engine is running, the reverse gate may move down and a person boarding could be pinched.The heavier the total weight of the operator and passenger(s), the more difficult it will be to balance the watercraft. Do not operate the watercraft when the total weight exceeds 240 kg (530 lb) including any cargo.To board with passenger(s):(1) Board as noted in the previous section“Boarding alone”.(3) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch.(4) Grip the handlebars with both hands and place both feet on the floor of the foot- well.(5) Look in all directions, start the engine,and then start off slowly. EJU43260Boarding with passenger(s)EWJ01800  Severe internal injuries can occur if wa- ter is forced into body cavities as a re- sult of being near the jet thrust nozzle. Do not start the engine until the passen- gers are seated with their feet on the floor of the footwell and are securely(2) Grip the handlebars with both hands and place both feet on the floor of the foot- well.(3) Have the first passenger move to the rear of the watercraft.WARNING81]]></page><page Index="89" isMAC="true"><![CDATA[(4) Have the first passenger board using the same procedure as the operator, place their feet on the floor of the footwell, and securely hold on to the operator.(5) Have the second passenger follow the same procedure. When the second pas- senger is boarding, try to balance the watercraft together with the first passen- ger.Operationare securely holding on to the person in front of them or to the handgrip provided.WARNING(6) Make sure that the passenger(s) have their feet on the floor of the footwell and(7) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch.(8) Look in all directions, start the engine,and then start off slowly. EJU33083Starting offEWJ00712To avoid collisions:  Scan constantly for people, objects, andother watercraft. Be alert for conditions that limit your visibility or block your vi- sion of others.  Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft.  Do not follow directly behind watercraft or other boats. Do not go near others to spray or splash them with water. Avoid sharp turns or other maneuvers that make it hard for others to avoid you or understand where you are going. Avoid areas with submerged objects or shal- low water.  Take early action to avoid collisions. Re- member, watercraft and other boats do not have brakes. Do not release the throttle lever when trying to steer away82]]></page><page Index="90" isMAC="true"><![CDATA[Operationfrom objects—you need throttle to steer.ECJ01341NOTICENever run the engine in water that is less than 60 cm (2 ft) deep from the bottom of the watercraft, otherwise pebbles or sand could be sucked into the jet intake, caus- ing impeller damage and engine overheat- ing.EJU43271Starting off from a trailer(1) Launch the watercraft.(2) Attach the engine shut-off cord (lanyard)to your left wrist, and then attach the clipto the engine shut-off switch.(3) Look in all directions, and then start theengine.(4) Squeeze the RiDE lever and move thewatercraft back slowly. (See page 37 forRiDE lever operation procedures.)EJU33114Boarding and starting off from a dock(1) Board the watercraft from the side.(2) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clipto the engine shut-off switch.(3) Push the watercraft away from the dock,grip the handlebars with both hands, andplace both feet on the floor of the foot- well.(4) Look in all directions, start the engine,and then start off slowly. EJU33236Capsized watercraftEWJ00672Improper uprighting can cause injury.  Be sure to shut the engine off by pulling on the engine shut-off cord (lanyard) to remove the clip from the engine shut-offswitch.  Do not put your hands in the intakegrate.If the watercraft capsizes, turn it over imme- diately.To upright the watercraft:(1) Remove the clip from the engine shut-offswitch.(2) Swim to the rear of the watercraft. Turnthe watercraft over clockwise by pulling on the ride plate with your left hand while pushing down on the gunwale with your right hand or foot.If the port (left) side of the capsized wa- tercraft is tilting up, push down on the gunwale so that the port (left) side is down before turning the watercraft clockwise. NOTICE: Do not turn the watercraft over counterclockwise,WARNING83]]></page><page Index="91" isMAC="true"><![CDATA[otherwise water can enter the engine, which can result in severe damage. [ECJ00542](3) Start the engine and operate the water- craft at planing speed to drain the bilge water from the engine compartment. (See page 60 for information on draining the bilge water. If the engine does not start, see “Towing the watercraft” on page 103 or “Submerged watercraft” on page 103.) NOTICE: Do not run the en- gine at full throttle for at least 1 minute after the engine has been restarted. Bilge water in the engine compart- ment can splash into the engine, which can result in severe damage.[ECJ00554] EJU43281Beaching and docking the watercraftTo beach the watercraft:(1) Make sure that there are no boats, swim-Operation(2) Release the throttle lever to reduce speed about 110 m (360 ft) before you reach the intended beaching area.(3) Slowly approach the beach using the throttle lever and RiDE lever to control the watercraft speed.(4) After reaching land, stop the engine, and then get off the watercraft and pull it up on the beach.To dock the watercraft:(1) Make sure that there are no boats, swim-mers, or obstacles near the dock.(2) Release the throttle lever to reduce speed about 110 m (360 ft) away fromthe dock.(3) Slowly approach the dock using thethrottle lever and RiDE lever to controlthe watercraft speed.(4) After coming alongside the dock, stopthe engine, and then get off the water-craft. EJU37194Operating in weeded areasAlways avoid using your watercraft in areas where weed growth is thick. If operating in weeded areas is unavoidable, alternately squeeze the throttle lever and relax your grip on the throttle lever to vary the engine speed. Weeds tend to become clogged more when operating at a steady speed and at trolling speed. If weeds may have clogged the intake area, clean the jet intake. (See page 99 for in-formation on the jet intake.)EJU40242After removing the watercraft fromthe waterECJ01311NOTICEDo not run the engine over 4000 r/min on land. Also, do not run the engine for more than 15 seconds without supplying water, otherwise the engine could overheat.mers, or obstacles near the beach.84]]></page><page Index="92" isMAC="true"><![CDATA[OperationAfter operating and removing the watercraft from the water, promptly discharge the re- maining water from the cooling water pas- sages.To discharge water from the cooling water passages:(1) Make sure that the area around the wa-tercraft is clear, and then start the en-gine.(2) Discharge the remaining water out of thecooling water passages by alternately squeezing and releasing the throttle lever quickly for 10 to 15 seconds.(3) Stop the engine.85]]></page><page Index="93" isMAC="true"><![CDATA[EJU37146EWJ00331Post-operation careCare and storage(3) Connect the garden hose adapter to a garden hose.WARNING1Always place the watercraft upright in a horizontal position when storing it, other- wise fuel could leak out into the engine or engine compartment, which could create a fire hazard.After using the watercraft, always take it out of the water, clean it, and store it. Leaving the watercraft in the water for extended periods will accelerate the rate of normal deteriora- tion of the jet pump and hull. Marine organ- isms and corrosion are some of the conditions that can shorten the life of manywatercraft components.EJU43651Flushing the cooling water passages ECJ01311NOTICEDo not run the engine over 4000 r/min on land. Also, do not run the engine for more than 15 seconds without supplying water, otherwise the engine could overheat.Flush the cooling water passages to prevent them from clogging with salt, sand, or dirt.(1) Place the watercraft in a horizontal posi-tion.(2) Remove the seats and watertight stor-age compartment. (See page 49 for seat removal and installation procedures and page 54 for information on the watertight storage compartment.)1 Garden hose adapter(4) Loosen the flushing hose connector cap and remove it. Insert the garden hose adapter into the flushing hose connector by pushing and twisting it until it is se- curely connected.1 321 Garden hose adapter2 Flushing hose connector3 Flushing hose connector cap(5) Connect the garden hose to a water tap.(6) Make sure that the area around the wa- tercraft is clear, and then start the en- gine. Immediately after the engine starts, fully turn the water supply on so that wa-86]]></page><page Index="94" isMAC="true"><![CDATA[Care and storageter flows out continually from the jet thrust nozzle.(3)(4) (5) (6) (7)(8)(9)NOTICE: Do not use high-pressure water when rinsing the engine or en- gine compartment as severe engine damage could result. [ECJ00572]Drain the water from the engine com- partment. (See page 60 for information on draining the bilge water.)Wipe the engine and engine compart- ment with a dry cloth.Wash down the hull, deck, and jet pump with fresh water.Wipe the hull, deck, and jet pump with a dry cloth.Wipe all vinyl and rubber components, such as the seats and engine compart- ment seals, with a vinyl protectant such as Yamaha Protectant.To minimize corrosion, spray metallic parts of the hull, deck, and engine with a rust inhibitor such as Yamaha Silicone Protectant and Lubricant.Allow the engine compartment to air dry completely before installing the seats. Securely install the seats in their original(7) Run the engine at idling speed for about 3 minutes watching the engine condition. If the engine stops while flushing, turn the water supply off immediately and perform the procedure again from step 6. NOTICE: Do not supply water to the cooling water passages when the en- gine is not running. The water could flow back through the muffler into the engine, causing severe engine dam- age. [ECJ00123](8) Turn the water supply off.(9) Discharge the remaining water out of thecooling water passages by alternately squeezing and releasing the throttle lever quickly for 10 to 15 seconds.(10) Stop the engine.(11) Remove the garden hose adapter, andthen securely install the flushing hose connector cap by tightening it until it stops.(12) Securely install the watertight storagecompartment and seats in their originalpositions.EJU33746Cleaning the watercraft(1) Remove the seats. (See page 49 for seat removal and installation procedures.)(2) Rinse the engine and engine compart-ment with a small amount of water.87(10) EJU41631positions.Battery careIf the watercraft will not be used for more than a month, remove the battery from the water- craft, check it, and then store it in a cool, dry place.EWJ00792Battery electrolyte is poisonous and dan- gerous, causing severe burns, etc. Elec- trolyte contains sulfuric acid. Avoid contact with skin, eyes, or clothing. AntidotesExternal: Flush with water.Internal: Drink large quantities of water or milk. Follow with milk of magnesia, beatenWARNING]]></page><page Index="95" isMAC="true"><![CDATA[egg, or vegetable oil. Call a physician im- mediately.Eyes: Flush with water for 15 minutes and get prompt medical attention.Batteries produce explosive gases. Keep sparks, flames, cigarettes, etc., well away. If using or charging the battery in an en- closed space, make sure that it is well ventilated. Always shield your eyes when working near batteries.Keep out of the reach of children.To remove the battery:(1) Disconnect the negative (–) battery lead.(2) Disconnect the positive (+) battery lead.(3) Disconnect the breather hose.(4) Unhook the battery bands, and then re-move the battery from the watercraft.12341 Negative (–) battery terminal: Black lead 2 Battery band3 Positive (+) battery terminal: Red lead4 Breather hoseChecking the battery  Make sure that the battery case is not dam- aged.  Make sure that the battery terminals are not corroded or damaged.  Make sure that the breather hose is not clogged or damaged.Care and storageChecking the electrolyte levelMake sure that the electrolyte level is be- tween the maximum and minimum level marks.If the electrolyte level is low, add distilled wa- ter to raise it to the specified level. NOTICE: Use only distilled water for replenishing the battery, otherwise battery life could be shortened. [ECJ00242]1 Maximum level mark 2 Minimum level markIf distilled water was added, check the bat- tery voltage.It is recommended to have a Yamaha dealer check the battery voltage and charge the bat- tery. If you charge the battery yourself, be sure to read and follow the instructions pro- vided with the battery tester and charger you use. NOTICE: Do not attempt to charge a battery hastily. Battery life could be short- ened. [ECJ00252]88]]></page><page Index="96" isMAC="true"><![CDATA[Care and storageChecking the battery bandsMake sure that the battery bands are not damaged.1 Battery bandTo store the battery:(1) Clean the battery case using fresh water.(2) If the battery terminals are dirty or cor-roded, clean them using a wire brush.1 Battery terminal(3) Apply YAMALUBE MARINE GREASE tothe battery terminals.(4) Store the battery in a cool, dry place.NOTICE: Storing the battery in an un- charged condition can cause perma- nent battery damage. Check the battery periodically. [ECJ00103]To install the battery:(1) Place the battery in the battery compart-ment and hook the battery bands ontothe holders.(2) Connect the positive (+) battery lead (red)to the positive (+) battery terminal.NOTICE: Reversal of the battery leadswill damage the electrical parts. [ECJ00262] (3) Connect the negative (–) battery lead (black) to the negative (–) battery termi-nal.(4) Connect the breather hose to the bat-tery. WARNING! Fire or explosion could result if the breather hose is damaged, obstructed, or not connect- ed properly. [EWJ00452](5) Make sure that the battery is securely held in place.89Recommended water-resistant grease: YAMALUBE MARINE GREASE]]></page><page Index="97" isMAC="true"><![CDATA[EWJ00331Long-term storageCare and storageEJU33493Recommended water-resistant grease: YAMALUBE MARINE GREASEWARNINGAlways place the watercraft upright in a horizontal position when storing it, other- wise fuel could leak out into the engine or engine compartment, which could create a fire hazard.Storage for long periods of time, such as win- ter storage, requires preventive maintenance to ensure against deterioration. It is advisable to have the watercraft serviced by a Yamaha dealer prior to storage.However, the following procedures can beperformed easily by the owner.EJU40253Cleaning(1) Flush the cooling water passages. (Seepage 86 for information on flushing the cooling water passages.)TIP:If you will be storing the watercraft for a pro- longed period, such as winter storage, top off the fuel tank with fresh gasoline and add one ounce of Yamaha Fuel Stabilizer and Condi- tioner to each gallon of fuel in the fuel tank before starting the engine.(2) Clean the watercraft. (See page 87 for in- formation on cleaning the watercraft.) Wax the hull with a non-abrasive waxsuch as Yamaha Silicone Wax. EJU43291LubricationUse a Yamaha Power Cable Luber and spray Yamaha Lube-Zall between the inner and outer cables to lubricate the cables and purge out any dirt and moisture.To keep moving parts sliding or rotating smoothly, lubricate them with water-resistant grease.  Steering cable (jet thrust nozzle end) and electric trim rod (jet thrust nozzle end)  Shift rod (reverse gate end)EJU40262RustproofingSpray metallic parts of the hull, deck, and en- gine with a rust inhibitor such as Yamaha Sil- icone Protectant and Lubricant.Have a Yamaha dealer rustproof the internal engine components.90]]></page><page Index="98" isMAC="true"><![CDATA[MaintenanceEJU33758MaintenancePeriodic checks and lubrication will keep your watercraft in the safest and most effi- cient condition possible. Therefore, make sure to carry out the periodic maintenance. Safety is an obligation of the watercraft own- er. Proper maintenance must be carried out to keep the exhaust emission and sound lev- els within the regulated limits. The most im- portant points of watercraft inspection and lubrication are explained on the following pages.See a Yamaha dealer for genuine Yamaha re- placement parts and optional accessories designed for your watercraft.Remember, failures that are the result of the installation of parts or accessories which are not qualitatively equivalent to genuine Yamaha parts are not covered by the limited warranty.Maintenance, replacement, or repair of the emission control devices and system may be performed by any marine SI engine repair establishment or individual. War- ranty repair, however, must be performed at an authorized Yamaha marine dealer- ship.EWJ00312Be sure to turn off the engine when you perform maintenance unless otherwise specified. If you are not familiar with ma- chine servicing, this work should be done by a Yamaha dealer or other qualified me- chanic.A service manual is available for purchase through a Yamaha dealer for owners who have the mechanical skills, tools, and other equipment necessary to perform mainte-nance not covered by this owner’s/operator’smanual. EJU33803 Tool kitA tool kit is included with this watercraft. Place the tool kit in a waterproof bag and al- ways carry it with you whenever you use the watercraft.1 Tool bag2 Screwdriver3 Garden hose adapter4 10/12 mm box wrench5 Pliers6 10/12 mm open-end wrenchEJU42021Removing and installing the engine coverThe engine cover is removable.To remove the engine cover:(1) Remove the seats. (See page 49 for seat removal and installation procedures.)(2) Remove the engine cover screws.WARNING1911 Engine cover screw]]></page><page Index="99" isMAC="true"><![CDATA[(3) Lift up the engine cover to remove it.Maintenance11 Engine coverTo install the engine cover:(1) Place the engine cover in its original po-sition, and then push it down.(2) Install the engine cover screws, and then tighten them to the specified torque.(3) Securely install the seats in their original positions.Tightening torque: Engine cover screw:4.5 Nm (0.46 kgf-m, 3.3 ft-lb)92]]></page><page Index="100" isMAC="true"><![CDATA[MaintenanceEJU43101Periodic maintenance chartThe periodic maintenance chart gives general guidelines for periodic maintenance. Have a Yamaha dealer perform the checks in the following chart. However, maintenance may need to be performed more frequently depending on your operating conditions. If you have any questions, consult a Yamaha dealer.This “√” mark indicates items to be checked and serviced by a Yamaha dealer.ItemOperationInitialThereafter everyPage10 hours50 hours or 12 months *1100 hours or 12 months *1200 hours or 24 months *1Fuel lineCheck fuel hoses and clamps√—Fuel filler cap/Wa- ter separatorCheck O-rings for cracks and deformation√—Fuel tankCheck installation and straps√—Water inlet strainerCheck for clogs and dam- age√—Cooling water hos- esCheck for damage and leakage, and check clamps√—Engine oilReplace√√94Oil filterReplace√94Intermediate hous- ingLubricate√—Spark plugsCheck√√—BatteryCheck specific gravity of electrolyte, terminals, bands, and breather hose√—Battery leadsCheck terminals√—Steering masterCheck operation and for looseness√√—Steering cableCheck exterior and con- nections, and lubricate√—Electric trim rodCheck exterior and con- nections, and lubricate√—Shift rod and re- verse gateCheck exterior and con- nections, and lubricate√—Air filter elementCheck for damage and dirt√—Air intake hosesCheck for damage, and check clamps√—Throttle bodyLubricate throttle valves√—93]]></page><page Index="101" isMAC="true"><![CDATA[MaintenanceItemOperationInitialThereafter everyPage10 hours50 hours or 12 months *1100 hours or 12 months *1200 hours or 24 months *1Exhaust systemCheck for exhaust leak- age, and check hoses and clamps√—Breather hoseCheck breather hose and clamps√—ImpellerCheck for bends, dam- age, and foreign material√—Jet thrust nozzleCheck movement, and lu- bricate√—Jet vacuum bilgeCheck hoses for clogs and damage, check clamps, and clean bilge strainer√—Stern drain plugsCheck O-rings√—AnodeCheck for corrosion, and clean√ *2—Valve clearanceCheck and adjust√ *2—Rubber couplingCheck for cracks, inden- tations, looseness, and noise√—Engine mountCheck for damage and peeling√—*1: Whichever comes first.*2: Check every 200 hours.Perform the pre-operation checks and post-operation checks before performing periodicmaintenance.EJU36943Engine oil and oil filter EWJ00341Engine oil is extremely hot immediately af- ter the engine is turned off. Coming in con- tact with or getting any engine oil on your clothes could result in burns.ECJ00992NOTICEDo not run the engine with too much or not enough oil in the engine, otherwise the en- gine could be damaged.It is recommended to have a Yamaha dealer change the engine oil and the engine oil filter. However, if you choose to change the oil and filter on your own, consult a Yamaha dealer.WARNING94]]></page><page Index="102" isMAC="true"><![CDATA[SpecificationsEJU34543Specifications Watercraft capacity:Maximum people on board: 3 personMaximum load capacity: 240 kg (530 lb)Dimensions:Length:VXS 3340 mm (131.5 in) VXR 3350 mm (131.9 in)Width:1220 mm (48.0 in)Height:1190 mm (46.9 in)Dry weight:VXS 347 kg (765 lb) VXR 348 kg (767 lb)Performance:Maximum fuel consumption:48.7 L/h (12.9 US gal/h, 10.7 Imp.gal/h)Cruising range at full throttle: 1.44 hourTrolling speed: 1300 ±100 r/minEngine:Engine type:Liquid cooled 4-stroke, DOHCNumber of cylinders: 4Engine displacement: 1812 cm3Bore × stroke:86.0 × 78.0 mm (3.39 × 3.07 in)Compression ratio: 11.0 : 1Valve clearance-intake (cold): 0.14–0.23 mm (0.0055–0.0091 in)Valve clearance-exhaust (cold): 0.28–0.37 mm (0.0110–0.0146 in)Lubrication system: Wet sumpCooling system: WaterStarting system: ElectricIgnition system: T.C.I.Spark plug: LFR6ASpark plug gap:0.8–0.9 mm (0.031–0.035 in)Battery capacity: 12 V, 19 Ah Charging system:Flywheel magnetoDrive unit:Propulsion system: Jet pumpJet pump type:Axial flow, single stageImpeller rotation: CounterclockwiseJet thrust nozzle angle: 24.0+24.0 °Jet thrust nozzle trim angle: -6, -3, 0, 3, 6 °Fuel and oil:Recommended fuel:Regular unleaded gasolineMinimum octane rating (PON): 86Minimum octane rating (RON): 90Recommended engine oil type SAE:SAE 10W-30, 10W-40, 20W-40, 20W-50Recommended engine oil grade API: API SE,SF,SG,SH,SJ,SLFuel tank total capacity:70 L (18.5 US gal, 15.4 Imp.gal)Engine oil quantity with oil filter replacement: 3.6 L (3.81 US qt, 3.17 Imp.qt)Engine oil quantity without oil filter replacement: 3.5 L (3.70 US qt, 3.08 Imp.qt)Engine oil total quantity:5.3 L (5.60 US qt, 4.66 Imp.qt)95]]></page><page Index="103" isMAC="true"><![CDATA[EJU34562TroubleshootingIf you have any trouble with your watercraft, use the troubleshooting chart to check for thepossible cause.If you cannot find the cause, consult a Yamaha dealer.EJU43512Troubleshooting chartConfirm the possible cause and remedy, and then refer to the applicable page.Trouble recoveryTROUBLEPOSSIBLE CAUSEREMEDYPAGEEngine does not start (Starter motor does not turn over)Yamaha Se- curity SystemLock mode selectedSelect unlock mode32Engine shut- off switchClip not in placeInstall clip33FuseBurned outReplace fuse and check wiring101BatteryRun downRecharge87Poor terminal con- nectionsTighten as required87Terminal corrodedClean or replace87Starter motorFaultyHave serviced by Yamaha dealer—Engine does not start (Starter motor turns over)Throttle leverSqueezedRelease33FaultyHave serviced by Yamaha dealer—RiDE leverSqueezedRelease33FaultyHave serviced by Yamaha dealer—FuelFuel tank emptyRefill as soon as pos- sible56Stale or contaminat- edHave serviced by Yamaha dealer—Fuel tankWater or dirt presentHave serviced by Yamaha dealer—Spark plugFouled or defectiveHave serviced by Yamaha dealer—Spark plug capNot connected or looseHave serviced by Yamaha dealer—Connected to wrong cylinderHave serviced by Yamaha dealer—Fuel injec- tion systemFuel pump faultyHave serviced by Yamaha dealer—96]]></page><page Index="104" isMAC="true"><![CDATA[Trouble recoveryTROUBLEPOSSIBLE CAUSEREMEDYPAGEEngine runs irregu- larly or stallsFuelFuel tank emptyRefill as soon as pos- sible56Stale or contaminat- edHave serviced by Yamaha dealer—Fuel tankWater or dirt presentHave serviced by Yamaha dealer—Spark plugFouled or defectiveHave serviced by Yamaha dealer—Incorrect heat rangeHave serviced by Yamaha dealer—Gap incorrectHave serviced by Yamaha dealer—Spark plug capNot connected or looseHave serviced by Yamaha dealer—Cracked, torn, or damagedHave serviced by Yamaha dealer—Electrical wir- ingLoose connectionHave serviced by Yamaha dealer—Fuel injec- tion systemFaulty or clogged in- jectorsHave serviced by Yamaha dealer—Warning light or in- dicator blinks or comes onFuel level warningFuel tank emptyRefill as soon as pos- sible56Oil pressure warningOil pressure droppedHave serviced by Yamaha dealer46Engine over- heat warningJet intake cloggedClean99Check en- gine warningFaulty sensorsHave serviced by Yamaha dealer4797]]></page><page Index="105" isMAC="true"><![CDATA[Trouble recoveryTROUBLEPOSSIBLE CAUSEREMEDYPAGEWatercraft slow or loses powerWatercraft operation modeLow RPM Mode acti- vatedDeactivate Low RPM Mode41CavitationJet intake cloggedClean99Impeller damaged or wornHave serviced by Yamaha dealer99Engine over- heat warningEngine speed reduc- tion control activatedClean jet intake and cool engine47Oil pressure warningEngine speed reduc- tion control activatedAdd oil46Spark plugFouled or defectiveHave serviced by Yamaha dealer—Incorrect heat rangeHave serviced by Yamaha dealer—Gap incorrectHave serviced by Yamaha dealer—Spark plug capNot connected or looseHave serviced by Yamaha dealer—Electrical wir- ingLoose connectionHave serviced by Yamaha dealer—FuelStale or contaminat- edHave serviced by Yamaha dealer—Air filterCloggedHave serviced by Yamaha dealer—Oil buildupHave serviced by Yamaha dealer—Throttle leverFaultyHave serviced by Yamaha dealer—98]]></page><page Index="106" isMAC="true"><![CDATA[Trouble recoveryEJU34625Emergency proceduresEJU34635Cleaning the jet intake and impellerEWJ00783Before attempting to remove weeds or de- bris from the jet intake or impeller area, shut the engine off and remove the clip from the engine shut-off switch. Severe in- jury or death could result from coming in contact with the rotating parts of the jet pump.If weeds or debris gets caught in the jet intake or impeller, cavitation can occur, causing jet thrust to decrease even though engine speed rises. If this condition is allowed to continue, the engine will overheat and may seize. NOTICE: If weeds or debris gets caught in the jet intake, do not operate the water- craft above trolling speed until they have been removed. [ECJ00654]If there is any sign that the jet intake or impel- ler is clogged with weeds or debris, return to shore and check the intake and impeller. Al-ways stop the engine before beaching the watercraft.WARNING99(1) Place a suitable clean cloth or carpeting underneath the watercraft to protect it from abrasions and scratches. Turn the watercraft on its side as shown. NOTICE: Always turn the watercraft over onto its port (left) side. When turning the watercraft on its side, sup- port the bow so that the handlebars are not bent or damaged. [ECJ00662]]]></page><page Index="107" isMAC="true"><![CDATA[(2) Remove any weeds or debris from around the jet intake, drive shaft, impel- ler, jet pump housing, and jet thrust noz- zle.If debris is difficult to remove, consult aYamaha dealer. EJU43471Raising the reverse gateIf the RiDE system malfunctions and the re- verse gate remains in the lowered position, the watercraft will not be able to move for- ward.After raising the reverse gate so that the wa- tercraft can move forward, immediately re- turn to shore and have a Yamaha dealer service the watercraft.To raise the reverse gate:(1) Stop the engine and remove the clip fromthe engine shut-off switch.(2) Enter the water and move to the rear ofthe watercraft.(3) Slide the shift rod joint toward the bow,and then disconnect the shift rod joint from the ball joint.Trouble recovery(4) Raise the reverse gate to the forward po- sition.1212WARNING1 Shift rod joint2 Ball joint1 Reverse gate2 Forward positionTIP:  While the shift rod is disconnected, the re- verse gate will not move to the neutral po- sition or reverse position even if the RiDE lever is squeezed.  If the RiDE lever is squeezed while the shiftrod is disconnected, the watercraft willmove forward. EJU34642Jumping the batteryIf the watercraft battery has run down, the en-gine can be started using a 12-volt boosterbattery and jumper cables. EJU34664Connecting the jumper cables EWJ01251To avoid battery explosion and serious damage to the electrical system:  Do not reverse the polarity of the jumpercables when connecting to the batter-ies.  Do not connect the negative (–) jumpercable to the negative (–) terminal of thewatercraft battery.  Do not touch the positive (+) jumper ca-ble to the negative (–) jumper cable.100]]></page><page Index="108" isMAC="true"><![CDATA[Trouble recovery(1) Connect the positive (+) jumper cable to the positive (+) battery terminals of both batteries.(2) Connect one end of the negative (–) jumper cable to the negative (–) battery terminal of the booster battery.(3) Connect the other end of the negative (–) jumper cable to an engine hanger.EJU44050Replacing the fusesIf a fuse is blown, replace it with the proper fuse.1234211 Good fuse 2 Blown fuse121 Positive (+) jumper cable2 Booster battery3 Negative (–) jumper cable4 Engine hanger(4) Start the engine, and then disconnect the jumper cables by reversing the steps above. (See page 33 for information on starting the engine.)1 Good fuse 2 Blown fuseTo replace a fuse:(1) Remove the seats and removable water-tight storage compartment. (See page 49 for seat removal and installation proce- dures and page 54 for information on the removable watertight storage compart- ment.)101]]></page><page Index="109" isMAC="true"><![CDATA[(2) While pushing the projection on each lock, slide the locks outward.Trouble recovery(4) While pushing both sides of the fuse box cover inward, pull the cover toward the bow and remove it.1 Lock2 Projection1 Fuse box cover(5) When replacing the SCU fuse, remove the screws, and then remove the fuse. Install the spare fuse, and then tighten the screws.(3) Remove the electrical box cover from the electrical box and move it under the deck beam toward the stern. NOTICE: Do not attempt to forcefully remove the elec- trical box cover from the watercraft. Otherwise, the electrical box cover, electrical system, and engine could be damaged. [ECJ02610]12345671 Electrical box cover10 51 Electronic throttle valve fuse 2 Fuel pump fuse3 Main relay drive fuse4 Main fuse5 Spare fuse 6 Fuse puller 7 Battery fuse 8 Screw9 SCU fuse (BCU fuse) 10 Security system fuse18 98211(6) When replacing a fuse other than the SCU fuse, remove the fuse using the fuse puller. Install a spare fuse of the proper amperage. WARNING! Do not102]]></page><page Index="110" isMAC="true"><![CDATA[Trouble recoveryuse fuses of a different amperage than recommended. Substitution with a fuse that has an improper rating can cause extensive electrical system damage and possible fire. [EWJ00803]  The towline should be long enough so that the watercraft will not collide with the towing boat when slowing down.If the watercraft becomes inoperative in the water, it can be towed to shore.To tow the watercraft:Use a towline that is three times the com- bined length of the towing boat and the wa- tercraft.(1) Securely attach the towline to the bow eye of the watercraft being towed.Fuse amperage:Electronic throttle valve fuse:10 AFuel pump fuse:10 AMain relay drive fuse:10 A Main fuse: 20 ABattery fuse: 30 ASCU fuse: 50 ASecurity system fuse: 3A1(7) Securely install the fuse box cover in its original position.(8) Securely install the electrical box cover in its original position.(9) Slide the locks to their original positions to securely lock the electrical box cover in place.(10) Securely install the removable watertight storage compartment and seats in their original positions.If the fuse immediately blows again, the elec-trical system may be defective. If this occurs,have a Yamaha dealer service the watercraft. EJU34716Towing the watercraftEWJ00812  The operator of the towing boat must keep speed to a minimum and avoid traffic or obstacles which could be a hazard to the operator on the water- craft.1 Bow eye(2) Sit astride the seat and hold on to the handlebars in order to balance the water- craft. NOTICE: The bow must be kept up out of the water during towing, oth- erwise water could flood the engine compartment or water could flow back into the engine, causing severe engine damage. [ECJ01331]Tow the watercraft at 8 km/h (5 mph) or less.NOTICE: Tow the watercraft at 8 km/h (5 mph) or less, otherwise water could flood the engine compartment or water could flow back into the engine, causing severeengine damage. [ECJ01322]EJU36156Submerged watercraftIf the watercraft is submerged or flooded withwater, drain the bilge water from the engineWARNING103]]></page><page Index="111" isMAC="true"><![CDATA[compartment. Then, have a Yamaha dealer service the watercraft as soon as possible.If the watercraft was submerged:(1) Remove the watercraft from the waterand drain the water from the storage compartments. (See page 52 for infor- mation on draining the storage compart- ments.)(2) Drain the bilge water from the engine compartment. (See page 60 for informa- tion on draining the bilge water.)(3) Have the watercraft serviced by a Yamaha dealer as soon as possible. NOTICE: Be sure to have a Yamaha dealer inspect the watercraft. Other- wise, serious engine damage could result. [ECJ00792]Trouble recovery104]]></page><page Index="112" isMAC="true"><![CDATA[Consumer informationEJU34784Limited warrantyYAMAHA MOTOR CORPORATION, U.S.A. WAVERUNNER® WATERCRAFT LIMITED WARRANTYYamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha WaveRunner watercraft purchased from an authorized Yamaha WaveRunner Watercraft Dealer in the United States (excluding its territories) will be free from defects in material and workmanship for the period of time stated herein, subject to certain stated limitations.PERIOD OF WARRANTY. Any new Yamaha WaveRunner watercraft purchased for pleasure use will be warranted for a period of one (1) year from the date of purchase, subject to exclusions noted herein. Any Yamaha WaveRunner watercraft purchased and utilized for commercial applications will be warranted for a period of ninety (90) days from the date of purchase, subject to exclusions noted herein. The battery will be warranted against defects in material or workmanship for thirty (30) days from the date of vehicle purchase for either pleasure or commercial use. Replacement parts used in warranty repairs will be warranted for the balance of the applicable warranty period.OBTAINING REPAIRS UNDER WARRANTY. During the period of warranty, any authorized Yamaha WaveRunner Watercraft Dealer will, free of charge, repair or replace, at Yamaha’s option, any part adjudged defective by Yamaha due to faulty workmanship or material from the factory. All parts replaced under warranty will become the property of Yamaha Motor Corporation, U.S.A.THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to:1. Operate, maintain, and store the WaveRunner watercraft as specified in the appropriate Owner’s/Operator’s Manual, and2. Give notice to an authorized Yamaha WaveRunner watercraft dealer of any and all apparent defects within ten (10) days afterdiscovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business.GENERAL EXCLUSIONS from this warranty shall include any failures caused by:a. Racing or competition use, modification of original parts, abnormal strain.b. Lack of proper maintenance and off-season storage as described in the Owner’s/Operator’s Manual.c. Installation of parts or accessories that are not equivalent in design and quality to genuine Yamaha parts.d. Use of lubricants, oils, and fuels that are not suitable for WaveRunner watercraft use.e. Damage as a result of accidents, collisions, contact with foreign materials, or submersion.f. Growth of marine organism on motor or hull surfaces.g. Normal deterioration.h. Gel coat stress cracksi. Damage due to improper transportation.SPECIFIC PARTS EXCLUDED FROM WARRANTY. Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, fuel filters, impeller and liner, and anodes are not covered by warranty. Charges for transporting the WaveRunner watercraft to and from an authorized Yamaha WaveRunner Watercraft Dealer are excluded from warranty coverage.EMISSION CONTROL WARRANTY.Yamaha warrants to the ultimate purchaser and any subsequent owner, that the exhaust emission control components on this engine are designed, built and equipped so as to conform at the time of sale with applicable regulations under section 213 of the Clean Air Act and that this engine is free from defects in materials and workmanship which cause said engine to fail to conform with applicable regulations for 30 months from the date of purchase or 175 hours of operation, whichever comes first. For evaporative emission components, for a failure that will increase evaporative emissions, the warranty coverage is 2 years from the date of purchase. Some states may have different emission control warranty provisions. As these vary from state to state, consult your Yamaha dealer or contact Yamaha Customer Relations at 1-800-962-7926 for more information.WARRANTY TRANSFER: To transfer the warranty from the original purchaser to any subsequent purchaser(s), it is imperative that the WaveRunner watercraft be inspected and registered for warranty by an authorized Yamaha WaveRunner watercraft dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer of ownership to the subsequent purchaser. A reasonable dealer-imposed fee may be charged for this inspection.YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITS STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, U.S.A. AND EXCLUDED FROM THIS WARRANTY.SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS OF USE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.105]]></page><page Index="113" isMAC="true"><![CDATA[Consumer informationTHIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.YAMAHA MOTOR CORPORATION, U.S.A. Post Office Box 6555 Cypress, California 90630WARRANTY QUESTIONS AND ANSWERSQ. What costs are my responsibility during the warranty period?A. The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision dam-ages.Q. What are some examples of “abnormal” strain, neglect, or abuse?A. These terms are general and overlap each other in areas. Specific examples include:Running the watercraft out of oil, operating the machine with a broken or damaged part which causes another part to fail, and so on. If you have any specific questions on operation or maintenance, please contact your Yamaha dealer for advice.Q. Does the warranty cover incidental costs such as transportation due to a failure? A. No. The warranty is limited to repair of the watercraft itself.Q. May I perform any or all of the recommended maintenance shown in the Owner’s/Operator’s Manual instead of having the dealer do them?A. Yes, if you are a qualified mechanic and follow the procedures specified in the Owner’s/Operator’s and Service Manual. We do rec- ommend, however, that items requiring special or equipment be done by a Yamaha dealer.Q. Will the warranty be void or cancelled if I do not operate or maintain my new watercraft exactly as specified in the Owner’s/Opera- tor’s Manual?A. No. The warranty on a new watercraft cannot be “voided” or “cancelled”. However, if a particular failure is caused by operation or maintenance other than as shown in the Owner’s/Operator’s Manual, that failure may not be covered under warranty.Q. What responsibility does my dealer have under this warranty? A. Each Yamaha dealer is expected to:1. Completely set up each new watercraft before sale.2. Explain the operation, maintenance, and warranty requirements to your satisfaction at the time of sale, and upon your request atany later date. In addition, each Yamaha dealer is held responsible for his setup, service and warranty repair work.Q. Is the warranty transferable to second owners?A. Yes. The remainder of the existing warranty can be transferred upon request. The unit has to be inspected and re-registered by anauthorized Yamaha dealer for the policy to remain effective.CUSTOMER SERVICEIf your watercraft requires warranty service, you must take it to any authorized Yamaha dealer within the continental United States. Be sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises regard- ing warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, this person is in the best position to help you. If you are still not satisfied and require additional assistance, please write:YAMAHA MOTOR CORPORATION U.S.A. CUSTOMER RELATIONS DEPARTMENT P.O. Box 6555Cypress, California 90630CHANGE OF ADDRESSThe federal government requires each manufacturer to maintain a complete, up-to-date list of all first purchasers against the possibility of a safety-related defect and recall. This list is complied from the purchase registrations sent to Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.If you should move after you have purchased your new watercraft, please advise us of your new address by sending a postcard listing your Yamaha model name, engine number, dealer number [or dealer’s name] as it is shown on your warranty card, your name and new mailing address.Mail to:YAMAHA MOTOR CORPORATION, U.S.A. P.O. Box 6555Cypress, California 90630 Attention: Warranty DepartmentThis will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.106]]></page><page Index="114" isMAC="true"><![CDATA[Consumer informationEJU34802YAMAHA EXTENDED SERVICE (Y.E.S.)Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.).• Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.• Y.E.S. is flexible. You choose the plan that is right for you: 12 months, 24 months, 36 months, or (on four-stroke models) 48 months beyond your warranty period.• Y.E.S. is designed and administered by the same Yamaha people who handle your warranty— and it shows in the comprehensive coverage benefits. There are no mileage limitations. Cover- age is not limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers manufacturing defects just like the warranty. See the sample contract at your Yamaha dealer to see how comforting uninterrupted factory-backed protection can be.• You do not have to pay anything for covered repairs. There is no deductible to pay, and repairs are not “pro-rated.” You do not have any “out-of-pocket” expenses for covered repairs.• In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost. TRIP gives you up to $250 reimbursement per occurrence for any reasonable expenses you incur because your Yamaha needs covered service: replacement vehicle rental, emergency towing, phone calls, even food and lodging when you are away from home. This superb cover- age goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as covered repairs during your entire Y.E.S. plan period.• Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.• Y.E.S. coverage is transferable to a new owner if you sell or trade-in. That can make your Yamaha much more valuable!This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service.We urge you to act now. You will get the excellent benefits of TRIP coverage right away, and you will rest easy knowing you will have strong factory-backed protection even after your Yamaha Limited Warranty expires.A special note:If visiting your dealer is not convenient, contact Yamaha with your Primary ID number (your Owner’s Manual shows you where to find this number). We will be happy to help you get the Y.E.S. coverage you need.Yamaha Service Marketing P.O. Box 6555Cypress, CA 90630 1-(866)-YES-EXTD (1-866-937-3983)107]]></page><page Index="115" isMAC="true"><![CDATA[AAfter removing the watercraft from the water ..................................................... 84Approval label of emission control certificate ................................................ 2BBattery care.............................................. 87 Battery checks ......................................... 66 Battery, jumping..................................... 100 Beaching and docking the watercraft ...... 84 Bilge water check..................................... 66 Bilge water, draining ................................ 60 Bilge water, draining on land ................... 60 Bilge water, draining on water ................. 60 Boarding alone ......................................... 80 Boarding and starting off from a dock ..... 83 Boarding the watercraft ........................... 80 Boarding with passenger(s) ..................... 81 Bow eye ................................................... 51 Bow storage compartment ...................... 52 CCapsized watercraft ................................. 83 Check engine warning ............................. 47 Cleaning ................................................... 90 Cleaning the watercraft ............................ 87 Cleat ......................................................... 51 Cooling water pilot outlet ......................... 35 Cooling water pilot outlet check .............. 71 Cruising limitations................................... 11 EElectric trim system.................................. 39 Emergency procedures............................ 99 Emission control information ..................... 2 Engine break-in ........................................ 62 Engine compartment check ..................... 65 Engine cover, removing and installing ..... 91 Engine idling speed check ....................... 73 Engine oil ................................................. 58 Engine oil and oil filter .............................. 94 Engine oil level check............................... 66 Engine oil requirements ........................... 58 Engine overheat warning ......................... 47 Engine serial number ................................. 1 Engine shut-off cord (lanyard) check ....... 68 Engine shut-off switch ............................. 33IndexEngine stop switch ................................... 33 Engine unit check..................................... 66 Enjoy your watercraft responsibly............ 24 Equipment ................................................ 49 FFire extinguisher check ............................ 70 Fire extinguisher holder and cover........... 54 Fire extinguisher holder, cover, andband checks ......................................... 69 Flushing the cooling water passages....... 86 Fuel .......................................................... 56 Fuel level check........................................ 65 Fuel level meter ........................................ 46 Fuel level warning..................................... 46 Fuel requirements .................................... 56 Fuel system checks ................................. 65 Fuses, replacing ..................................... 101 GGetting to know your watercraft .............. 74 Glossary, watercraft ................................. 26 Glove compartment ................................. 53 HHandgrip .................................................. 50 Hazard information................................... 16 Hood check .............................................. 71 Hour meter ............................................... 47 Hull and deck check ................................ 70 Hull Identification Number (HIN)................. 1 IIdentification numbers ............................... 1 Information display................................... 43 JJet intake and impeller, cleaning.............. 99 Jet intake checks ..................................... 70 Jet thrust nozzle and reverse gatecheck .................................................... 70 Jumper cables, connecting .................... 100 LLabels, important ....................................... 5 Labels, other .............................................. 8 Labels, warning .......................................... 6 Launching the watercraft ......................... 75 Learning to operate your watercraft......... 74 Leaving the watercraft.............................. 76108]]></page><page Index="116" isMAC="true"><![CDATA[IndexLimitations on who may operate the watercraft.............................................. 10 Limited warranty .................................... 105 Long-term storage ................................... 90 Low RPM Mode ....................................... 41 Lubrication ............................................... 90MMain components, location of ................. 27 Maintenance ............................................ 91 Manufactured date label ............................ 2 Multifunction information center .............. 43 Multifunction information center check ... 71 OOil pressure warning ................................ 46 Operating in weeded areas ...................... 84 Operating the watercraft .......................... 76 Operating the watercraft in reverse orneutral ................................................... 79 Operating your watercraft ........................ 74 Operation requirements ........................... 13 PPeriodic maintenance chart ..................... 93 Post-launch checks ................................. 71 Post-operation care ................................. 86 Pre-launch checks ................................... 65 Pre-operation check points ..................... 65 Pre-operation checklist ............................ 63 Primary Identification (PRI-ID) number ...... 1 RRaising the reverse gate ........................ 100 Reboarding step (VXR)............................. 50 Recommended equipment ...................... 15 Remote control transmitter ...................... 31 Remote control transmitter check ........... 68 RiDE lever................................................. 34 RiDE lever checks .................................... 68 Riding position ......................................... 75 Rules of the Road .................................... 19 Rustproofing ............................................ 90 SSafety equipment check .......................... 70 Seats ........................................................ 49 Shift indicator ........................................... 45 Shift system ............................................. 37 Shift system check................................... 72Speedometer ........................................... 43 Star labels .................................................. 3 Start switch .............................................. 33 Starting off ............................................... 82 Starting off from a trailer .......................... 83 Starting the engine on water .................... 75 Steering system ....................................... 35 Steering system checks ........................... 67 Stern drain plug checks ........................... 70 Stern eyes ................................................ 51 Stopping the engine ................................. 76 Stopping the watercraft ........................... 78 Storage compartment checks.................. 69 Storage compartments ............................ 52 Submerged watercraft ........................... 103 Switch checks .......................................... 69 TTachometer .............................................. 44 Throttle lever ............................................ 34 Throttle lever checks ................................ 68 To get more boating safety information ... 23 Tool kit ..................................................... 91 Towing the watercraft ............................ 103 Transporting on a trailer ........................... 61 Trim indicator ........................................... 45 Trim indicator check ................................ 72 Troubleshooting ....................................... 96 Troubleshooting chart .............................. 96 Turning the watercraft .............................. 77 VVoltmeter .................................................. 48WWakeboarding and water-skiing .............. 18 Water separator ....................................... 35 Water separator check ............................. 65 Watercraft characteristics ........................ 16 Watercraft control functions..................... 31 Watercraft operation functions ................ 37 Watercraft operation modes .................... 41 Watertight storage compartment ............. 54 YYAMAHA EXTENDED SERVICE(Y.E.S.) ................................................ 107Yamaha Security System ......................... 32 Yamaha Security System settings ........... 32109]]></page><page Index="117" isMAC="true"><![CDATA[EJU42011For your best ownership experience, think Genuine Yamaha!Genuine Yamaha Parts – Genuine Yamaha replacement parts are the exact same parts as the ones originally equipped on your vehicle, providing you with the performance and durability you have come to expect. Why settle for aftermarket parts that may not provide full confidence and satisfaction?Genuine Yamaha Accessories – Yamaha only offers accessories that meet our high standards for quality and performance. Buy with confidence, knowing your Genuine Yamaha Accessories will fit right and perform right – right out of the box.Yamalube – Take care of your Yamaha with legendary Yamalube oils, lubricants, and care products. They’re formulated and approved by the toughest judges we know: the Yamaha engineering teams that know your Yamaha from the inside out.Genuine Yamaha Service Manuals – Get the same factory manual for your vehicle that the technicians at your authorized Yamaha dealer use. Service manuals are available through your Yamaha dealer or you can order them directly through yamahapubs.com.Genuine Yamaha products are available only from your Yamaha dealer. Find out more at yamaha-motor.com]]></page></pages></Search>