﻿<?xml version="1.0" encoding="utf-8"?><Search><pages Count="124"><page Index="1" isMAC="true"><![CDATA[       2021 WaveRunner FX SVHO FX CRUISER SVHO FX LIMITED SVHO
 OWNER’S/OPERATOR’S MANUAL
U.S.A. Edition
LIT-18626-12-85 F3X-F8199-12
  Read this manual carefully before operating this watercraft.
]]></page><page Index="2" isMAC="true"><![CDATA[  WARNING: Operating, servicing and maintaining a recreational marine vessel can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. To minimize exposure, avoid breathing exhaust, service your vessel in a well-ventilated area and wear gloves or wash your hands frequently when servicing this vessel.
For more information go to www.P65warnings.ca.gov/marine
Read this manual carefully before operating this watercraft. This manual should stay with the WaveRunner if it is sold.
]]></page><page Index="3" isMAC="true"><![CDATA[EJU30183
Thank you for choosing a Yamaha watercraft. This owner’s/operator’s manual contains in- formation you will need for proper operation, maintenance, and care. A thorough under- standing of these simple instructions will help you to obtain maximum enjoyment from your new Yamaha. If you have any questions about the operation or maintenance of your watercraft, please consult a Yamaha dealer. In this manual, information of particular im- portance is distinguished in the following ways:
This is the safety alert symbol. It is used
to alert you to potential personal injury haz-
ards. Obey all safety messages that follow
this symbol to avoid possible injury or death. EWJ00072
A WARNING indicates a hazardous situa- tion which, if not avoided, could result in death or serious injury.
ECJ00092
A NOTICE indicates special precautions that must be taken to avoid damage to the watercraft or other property.
TIP:
A TIP provides key information to make pro-
cedures easier or clearer. EJU45461
Engine data recording
This model’s ECM stores certain engine data to assist in the diagnosis of malfunctions and for research, statistical analysis and develop- ment purposes.
Although the sensors and recorded data will vary by model, the main data points are:
  Engine status and engine performance data
This data will be uploaded only when a spe- cial Yamaha diagnostic tool is attached to the engine, such as when maintenance checks or service procedures are performed.
Yamaha will not disclose this data to a third party except in the following cases. In addi- tion, Yamaha may provide engine data to a contractor in order to outsource services re- lated to the handling of the engine data. Even in this case, Yamaha will require the contrac- tor to properly handle the engine data we provided and Yamaha will appropriately manage the data.
  With the consent of the boat owner
  Where obligated by law
  For use by Yamaha in litigation
  For general Yamaha-conducted research
purposes when the data is not related to an individual engine or owner
To the owner/operator
Important manual information
       ]]></page><page Index="4" isMAC="true"><![CDATA[Important manual information
EJU40401
Because Yamaha has a policy of continuing product improvement, this product may not be exactly as described in this owner’s/oper- ator’s manual. Specifications are subject to change without notice.
This manual should be considered a perma- nent part of this watercraft and should remain with it even if the watercraft is subsequently
sold. EJU30224
    WaveRunner FX SVHO / FX CRUISER SVHO / FX LIMITED SVHO OWNER’S/OPERATOR’S MANUAL ©2021 by Yamaha Motor Corporation, U.S.A.
1st Edition, April 2020
All rights reserved.
Any reprinting or unauthorized use without the written permission of Yamaha Motor Corporation, U.S.A. is expressly prohibited. Printed in U.S.A.
P/N LIT-18626-12-85
 ]]></page><page Index="5" isMAC="true"><![CDATA[ General and important labels...........1
Identification numbers .................... 1 Primary Identification (PRI-ID)
number............................................ 1 Hull Identification Number (HIN)......... 2 Engine serial number.......................... 2
Emission control information .......... 2 Approval label of emission control
certificate........................................ 2 Manufactured date label .................... 3 Star labels .......................................... 3
Important labels .............................. 5 Warning labels.................................... 6 Other labels........................................ 8
Safety information...........................10
Limitations on who may operate
the watercraft............................. 10 Cruising limitations........................ 11 Operation requirements ................ 12 Recommended equipment ........... 15 Hazard information........................ 15 Watercraft characteristics ............. 16 Wakeboarding and water-skiing ... 17 Rules of the Road ......................... 19
To get more boating safety information ................................. 23
Enjoy your watercraft responsibly................................. 24
Description....................................... 25
Watercraft glossary ....................... 25 Location of main components ...... 26
Control function operation ............. 30
Watercraft control functions ......... 30 Yamaha Security System................. 30 Engine stop switch .......................... 31 Engine shut-off switch .................... 31 Start switch ..................................... 31 Throttle lever .................................... 32 RiDE lever ........................................ 32
Table of contents
Steering system................................ 32 Adjustable tilt steering system ......... 33 Cooling water pilot outlets ............... 34 Water separator................................ 34
Watercraft operation ...................... 35
Watercraft operation functions ..... 35 Shift system ..................................... 35 Electric trim system.......................... 37
Watercraft operation modes......... 39 Reverse assist .................................. 39 T.D.E. (thrust directional
enhancer) ...................................... 39 No-wake mode................................. 40 Drive control mode........................... 41 Cruise assist..................................... 43
Instrument operation ...................... 45
Multifunction information center... 45 Operation buttons ............................ 46 Touch screen.................................... 46 Status area ....................................... 47 Home screen ................................... 47 Information screen .......................... 48 Drive control mode screen .............. 49 Setting menu screen ....................... 49 Engine lock screen .......................... 51 Warning function .............................. 51
Equipment operation ...................... 54
Equipment..................................... 54 Seats ................................................ 54 Handgrip........................................... 55 Reboarding grip................................ 55 Reboarding step............................... 55 Bow eye............................................ 56 Stern eyes ........................................ 56 Cleat................................................. 56 Pull-up cleats (FX CRUISER SVHO /
FX LIMITED SVHO) ....................... 57 Storage compartments .................... 57 Fire extinguisher holder and cover... 61 Optional part mounting bracket ....... 61
]]></page><page Index="6" isMAC="true"><![CDATA[Table of contents
Operation and handling requirements ................................... 62
Fuel requirements ......................... 62 Fuel................................................... 62 Engine oil requirements ................ 64 Engine oil.......................................... 64 Draining the bilge water ................ 66 Draining the bilge water on land ...... 66 Draining the bilge water on water .... 66 Transporting on a trailer................ 67
First-time operation ........................ 68
Engine break-in ............................. 68
Pre-operation checks ..................... 69
Pre-operationchecklist.................... 69 Pre-operation check points........... 71 Pre-launch checks ........................... 71 Post-launch checks ......................... 77
Operation ......................................... 79
Operating your watercraft ............. 79 Getting to know your watercraft ...... 79 Learning to operate your
watercraft...................................... 79 Riding position ................................. 80 Launching the watercraft ................. 80 Starting the engine on water ............ 80 Stopping the engine......................... 81 Leaving the watercraft...................... 81 Operating the watercraft .................. 81 Turning the watercraft...................... 82 Stopping the watercraft ................... 83 Operating the watercraft in reverse
or neutral ...................................... 84 Boarding the watercraft ................... 85 Starting off........................................ 87 Capsized watercraft ......................... 88 Beaching and docking the
watercraft...................................... 89 Operating in weeded areas .............. 89 After removing the watercraft from
the water....................................... 90
Care and storage ............................ 91
Post-operation care...................... 91 Flushing the cooling water
passages....................................... 91 Cleaning the watercraft .................... 92 Battery care...................................... 92
Long-term storage........................ 94 Cleaning ........................................... 94 Lubrication ....................................... 94 Rustproofing..................................... 95
Maintenance.................................... 96
Maintenance................................. 96 Removing and installing the engine
cover............................................. 96 Periodic maintenance chart ............. 98 Engine oil and oil filter .................... 100
Specifications................................ 101
Specifications............................. 101
Trouble recovery ........................... 102
Troubleshooting.......................... 102 Troubleshooting chart .................... 102 Emergency procedures .............. 105
Cleaning the jet intake and
impeller ....................................... 105
Raising the reverse gate ................ 106 Jumping the battery ....................... 106 Replacing the fuses........................ 107 Towing the watercraft..................... 109 Submerged watercraft ................... 109
Consumer information ................. 111
Limited warranty ......................... 111 YAMAHA EXTENDED SERVICE
(Y.E.S.)..................................... 113
Index............................................... 114
 ]]></page><page Index="7" isMAC="true"><![CDATA[Identification numbers
Record the Primary Identification (PRI-ID) number, Hull Identification Number (HIN), and engine serial number in the spaces provided for assistance when ordering genuine parts from a Yamaha dealer. Also record and keep these ID numbers in a separate place in case
your watercraft is stolen.
EJU42521
Primary Identification (PRI-ID) number The PRI-ID number is stamped on a plate at-
tached inside the engine compartment. (See page 54 for seat removal and installation pro- cedures and page 60 for information on the removable watertight storage compartment.)
1 Primary Identification (PRI-ID) number loca- tion
General and important labels
 EJU30263
MODEL:
FC1800-W (FX SVHO) FC1800A-W (FX CRUISER SVHO) FC1800B-W (FX LIMITED SVHO)
  1
              MODEL
YAMAHA MOTOR CO.,LTD.
ASSEMBLED IN U.S.A. WITH FOREIGN AND DOMESTIC COMPONENTS. ASSEMBLÉ EN U.S. AVEC DES COMPOSANTS ÉTRANGERS ET DOMESTIQUES.
PRI-I.D.
  1
]]></page><page Index="8" isMAC="true"><![CDATA[General and important labels
 EJU30301
Hull Identification Number (HIN)
The HIN is stamped on a plate attached to the aft deck.
EJU42680
Emission control information
This engine conforms to U.S. Environmental Protection Agency (EPA) and/or California Air Resources Board (CARB) regulations for ma- rine SI engines applicable at the time of man- ufacture.
This engine is certified to operate on premi-
um unleaded gasoline.
EJU42511
Approval label of emission control
certificate
This label is attached to the top of the cylin- der head and to the inside of the engine com- partment. (See page 54 for seat removal and installation procedures, page 96 for engine cover removal and installation procedures,
     1
     1 Hull Identification Number (HIN) location
EJU40471
Engine serial number
The engine serial number is stamped on a plate attached to the engine unit. (See page 54 for seat removal and installation proce- dures and page 96 for engine cover removal and installation procedures.)
      1
    1 Engine serial number location
 2
]]></page><page Index="9" isMAC="true"><![CDATA[and page 60 for information on the removable watertight storage compartment.)
gine cover removal and installation proce- dures.)
General and important labels
        1
       1
     1 Emission control information label location
1 Manufactured date label location
  EMISSION CONTROL INFORMATION
THIS ENGINE CONFORMS TO   CALIFORNIA AND U.S. EPA EXHAUST REGULATIONS
FOR SI MARINE ENGINES. REFER TO OWNER’S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
ENGINE FAMILY : DISPLACEMENT : liters MAX POWER : kW EPA/CA FEL : HC+NOx   , CO g/kW-h
YAMAHA MOTOR CO.,LTD.
         1
           1 Emission control information label location
EJU40491
Manufactured date label
This label is attached to the top of the cylin- der head. (See page 54 for seat removal and installation procedures and page 96 for en-
EJU30441
Star labels
This watercraft is labeled with a California Air Resources Board (CARB) star label. See be- low for a description of your particular label.
  1
          EPA/CA ,
KNCNPLINEME2 , KYMXPTANKTK2 , KBEMPMDRN003
KYMXPVSSLYM1
  1 Star label location
One Star - Low Emission
The one-star label identifies engines that meet the Air Resources Board’s Personal
3
]]></page><page Index="10" isMAC="true"><![CDATA[General and important labels
 Watercraft and Outboard marine engine 2001 exhaust emission standards. Engines meet- ing these standards have 75% lower emis- sions than conventional carbureted two- stroke engines. These engines are equivalent to the U.S. EPA’s 2006 standards for marine engines.
these standards have 65% lower emissions than One Star-Low Emission engines.
Four Stars - Super Ultra Low Emission
The four-star label identifies engines that meet the Air Resources Board’s Sterndrive and Inboard marine engine 2009 exhaust emission standards. Personal Watercraft and Outboard marine engines may also comply with these standards. Engines meeting these standards have 90% lower emissions than One Star-Low Emission engines.
  Two Stars - Very Low Emission
The two-star label identifies engines that meet the Air Resources Board’s Personal Watercraft and Outboard marine engine 2004 exhaust emission standards. Engines meet- ing these standards have 20% lower emis- sions than One Star-Low Emission engines.
  Three Stars - Ultra Low Emission
The three-star label identifies engines that meet the Air Resources Board’s Personal Watercraft and Outboard marine engine 2008 exhaust emission standards or the Sterndrive and Inboard marine engine 2003-2008 ex- haust emission standards. Engines meeting
4
]]></page><page Index="11" isMAC="true"><![CDATA[General and important labels
 EJU30454
Important labels
Read the following labels before using this watercraft. If you have any questions, consult a Yamaha dealer.
    4
     1 3
8
                  6
5
                                     72
9
      5
]]></page><page Index="12" isMAC="true"><![CDATA[General and important labels
EJU35914
Warning labels
If any of these labels are damaged or missing, contact a Yamaha dealer for replacements.
  1
          6
]]></page><page Index="13" isMAC="true"><![CDATA[General and important labels
  2
  3
F3J-U415B-00
 F3V-U416A-00
7
]]></page><page Index="14" isMAC="true"><![CDATA[General and important labels
EJU44221
Other labels
  4
5
6
F0V-U41F5-01
  F1S-U41G1-01
  7
FC1800
 F3J-U419B-00
8
]]></page><page Index="15" isMAC="true"><![CDATA[ 8
9
General and important labels
F3Y-U418E-40
9
]]></page><page Index="16" isMAC="true"><![CDATA[Safety information
EJU30675
The safe use and operation of this water- craft is dependent upon the use of proper riding techniques, as well as upon the common sense, good judgment, and ex- pertise of the operator. Every operator should know the following requirements before riding the watercraft.
  Before operating the watercraft, read this owner’s/operator’s manual, the Riding Practice Guide, the Riding Instruction card, and all labels on the watercraft. Also, watch the WaveRunner Basic Orientation Video linked to the following QR code.
EJU30733
Limitations on who may
operate the watercraft
  Make sure that the operator is 16 years of age or older and has taken a boater safety course.
Adults must supervise use by minors. Your state (or province) may have addition- al requirements. You can find local rules by contacting the United States Coast Guard (USCG), the National Association of State Boating Law Administrators, or your local Power Squadron.
  This watercraft is designed to carry the op- erator and up to 2 passengers. Never ex- ceed the maximum load limit or allow more than 3 persons (or 2 persons if a wake- boarder or water-skier is being pulled) to ride the watercraft at any time.
  Do not operate the watercraft with any pas- sengers on board until you have consider- able practice and experience riding alone. Operating the watercraft with passengers requires more skill. Take the time to be- come accustomed to the handling charac- teristics of the watercraft before trying any difficult maneuvers.
    https://yamahawaverunners.com/orientation A DVD is also available at your nearest dealer for your convenience.
These materials should give you an under- standing of the watercraft and its opera- tion.
  Never allow anyone to operate this water- craft until they too have read this own- er’s/operator’s manual, the Riding Practice Guide, the Riding Instruction card, and all labels, and, if possible, watched the WaveRunner Basic Orientation Video. Showing them the video may help reinforce the information contained in these materi- als.
   10
Maximum load:
240 kg (530 lb)
Load is the total weight of cargo, op- erator, and passengers.
 ]]></page><page Index="17" isMAC="true"><![CDATA[ EJU43323
Safety information
  Avoid sharp turns, slowing down rapidly by squeezing the RiDE lever forcefully, and other maneuvers that make it hard for oth- ers to avoid you or understand where you are going.
  Avoid areas with submerged objects or shallow water.
  Do not release the throttle lever when trying to steer away from objects—as with other powerboats, you need throttle to steer. Al- ways check throttle and steering controls before starting the watercraft.
  Ride within your limits and avoid aggres- sive maneuvers to reduce the risk of loss of control, ejection, and collision.
  This is a high performance boat—not a toy. Avoid aggressive operation, sharp turns, and unexpected acceleration that can cause you to be thrown off. Do not jump waves or wakes—jumping can cause inju- ries such as back or spinal injuries (paraly- sis), facial injuries, and broken legs, ankles, and other bones. Improper operation can result in severe injury or death.
  Do not operate the watercraft in rough wa- ter, bad weather, or when visibility is poor; this may lead to an accident causing injury or death. Be alert to the possibility of ad- verse weather. Take note of weather fore- casts and the prevailing weather conditions before setting out on your wa- tercraft.
  As with any water sport, you should not op- erate your watercraft without someone else nearby. If you operate further than swim- ming distance from shore, you should be accompanied by another boat or water- craft, but make sure you stay a safe dis- tance away. It’s good, common sense.
  Never operate in water that is less than 60 cm (2 ft) deep from the bottom of the wa-
Cruising limitations
  Scan constantly for people, objects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others.
  Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft.
  Do not follow directly behind watercraft or other boats.
  Do not go near others to spray or splash them with water, go too close to other boats, or go too fast for the traffic condi- tions.
  Take early action to avoid collisions. Re- member, watercraft and other boats do not have brakes. In addition, the Reverse with Intuitive Deceleration Electronics (RiDE) system is not a braking device for avoiding dangerous situations. The RiDE system is an electronic system for controlling the en- gine speed and reverse gate, which is lo- cated near the jet thrust nozzle. The RiDE lever located at the left handlebar grip can be used to change the direction of the jet thrust so that the watercraft moves in re- verse or is in neutral. The RiDE system as- sists the operator when slowing down and during slow-speed maneuvering, such as launching, beaching, and docking.
 11
]]></page><page Index="18" isMAC="true"><![CDATA[ Safety information
tercraft, otherwise you increase your chance of hitting a submerged object, which could result in injury.
60 cm (2 ft)
  This watercraft is not equipped with light- ing required for night operation. Do not op- erate the watercraft after sunset or before dawn, otherwise you increase the risk of colliding with another boat, which could re- sult in severe injury or death.
EJU43123
Operation requirements
  All riders must wear a personal flotation de- vice (PFD) that is approved by the appro- priate authorities and is suitable for personal watercraft use.
  Wear protective clothing. Severe internal injuries can occur if water is forced into body cavities as a result of falling into the water or being near the jet thrust nozzle. You must wear shorts with neoprene (wet- suit material) to keep water from being forcefully injected into the rectum or vagina during a fall backward. Riders not wearing neoprene shorts have received severe rec- tal, vaginal, and internal injuries resulting in permanent damage. Normal swimwear does not offer adequate protection.
    1
    2
  Eye protection is recommended to keep wind, water, and glare from the sun out of your eyes while you operate your water- craft. Restraining straps for eyewear are made which are designed to float should your eyewear fall in the water.
Footwear and gloves are recommended.
  Helmets meeting Snell or DOT standards are required for IJSBA-sanctioned races. You must decide whether to wear a helmet while you ride for recreation. You should know that a helmet could help protect you
        Follow navigation rules, and state/provin- cial and local laws that apply to watercraft.
12
1 Authority-approved PFD 2 Wetsuit bottom
]]></page><page Index="19" isMAC="true"><![CDATA[protection. Although helmets cannot pro- tect against all foreseeable impacts, a hel- met might reduce your injuries in a collision with a boat or other obstacle.
A helmet may have potential safety haz- ards, as well. Falling into the water could risk the chance of the helmet catching wa- ter, commonly known as “bucketing”, and the resulting strain on your neck could cause choking, severe and permanent neck injuries, or death. A helmet could also increase the risk of an accident if it reduces your vision or hearing, or if it distracts you or increases your fatigue.
How should you decide if a helmet’s poten- tial safety benefits outweigh its potential risks for you? Consider your particular rid- ing conditions. Consider factors such as your riding environment and your riding style and ability. Also consider the likeli- hood of traffic congestion, and the water surface conditions.
If you decide to wear a helmet based upon your riding circumstances, choose one carefully. Look for a helmet designed for personal watercraft use, if possible. Con- sider a helmet meeting Snell or DOT stan- dards. If you will be engaging in closed- course competition, follow the helmet re- quirements of the sanctioning organization.
  Never operate the watercraft after consum- ing alcohol or taking other drugs.
  For reasons of safety and proper care of the watercraft, always perform the pre-op- eration checks listed on page 69 before op- erating the watercraft.
  The operator should grip the handlebars firmly with both hands and the passengers
  The operator and passengers should al- ways keep their feet on the floor of the foot- well when the watercraft is in motion. Lifting your feet increases the chances of losing your balance, or hitting objects out- side the watercraft with your feet. Do not give a ride to children if their feet cannot reach the floor of the footwell.
  Never allow a passenger to ride in front of the operator.
  Always consult your doctor on whether it is safe for you to ride this watercraft if you are pregnant or in poor health.
  Do not attempt to modify this watercraft. Modifications to your watercraft may re- duce safety and reliability, and render the watercraft unsafe or illegal for use.
  Attach the engine shut-off cord (lanyard) to your left wrist and keep it free from the han- dlebars so that the engine stops if you, the operator, fall off. After riding, remove the engine shut-off cord (lanyard) from the wa-
Safety information
should hold on firmly, either to the person in front of them or to the handgrip provid-
 in certain kinds of accidents and that it
could injure you in others.
A helmet is designed to provide some head ed.
 13
]]></page><page Index="20" isMAC="true"><![CDATA[Safety information
tercraft to avoid accidental starting or un- authorized use by children or others.
fire extinguisher be approved by the US- CG.
            Scan carefully for swimmers and stay away from swimming areas. Swimmers are hard to see and you could accidentally hit some- one in the water.
  Avoid being hit by another boat. You should always take the responsibility to watch for traffic; other boaters may not be watching for you. If they do not see you, or if you maneuver more quickly than other boaters expect, you risk a collision.
  Maintain a safe distance from other boats and watercraft, and also watch for ski ropes or fishing lines. Obey the “Rules of the Road” and be sure to check behind you before making a turn or slowing down. (See “Rules of the Road” on page 19.)
  According to the USCG, boats under 6.1 m (20 ft) in length like your watercraft must carry a fire extinguisher of a 5-B (B-1) clas- sification, with a capacity of two pounds or more when navigating in waters under USCG jurisdiction. In addition, most state and local boating laws also require that the
14
]]></page><page Index="21" isMAC="true"><![CDATA[EJU30831 EJU42474
Recommended equipment
The following items should be carried on board your watercraft:
  Sound-signaling device
You should carry a whistle or other sound- signaling device that can be used to signal other boats. See “Rules of the Road” for more information.
  Visual distress signals
It is recommended that a U.S. Coast Guard approved pyrotechnic device be stored in a waterproof container on your watercraft. A mirror can also be used as an emergency signal. Contact a Yamaha dealer or the U.S. Coast Guard for more information.
  Watch
A watch is helpful so you will know how long you have been operating the water- craft.
  Towline
A towline can be used to tow a disabled watercraft in an emergency.
Safety information
 Hazard information
  Never start the engine or let it run for any length of time in an enclosed area. Exhaust fumes contain carbon monoxide, a color- less, odorless gas that may cause loss of consciousness and death within a short time. Always operate the watercraft in an open area.
  Do not touch the hot muffler or engine dur- ing or immediately after engine operation; they can cause serious burns.
  Do not place magnets or objects with a strong magnetic force near the throttle le- ver or RiDE lever. The electronic throttle mechanism of the levers can be adversely affected, which could cause loss of control. In addition, do not place objects suscepti- ble to magnetic forces (i.e., credit cards, watches, etc.) close to the throttle lever or RiDE lever.
15
]]></page><page Index="22" isMAC="true"><![CDATA[Safety information
EJU42415
Watercraft characteristics
  Jet thrust turns the watercraft. Releasing the throttle lever completely produces only minimum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to steer without throttle. This model is equipped with the Yamaha Engine Management System (YEMS) that includes an off-throttle steering (OTS) sys- tem. It will activate at planing speeds should you attempt to steer the watercraft after releasing the throttle lever. The OTS system assists in turning by continuing to supply some thrust while the watercraft is decelerating, but you can turn more sharp- ly if you apply throttle while turning the han- dlebars.
The OTS system does not function below planing speeds or when the engine is off. Once the engine slows down, the water- craft will no longer turn in response to han- dlebar input until you apply throttle again or you reach trolling speed.
Practice turning in an open area without obstacles until you have a good feel for this maneuver.
  This watercraft is water-jet propelled. The jet pump is directly connected to the en- gine. This means that jet thrust will produce some movement whenever the engine is running and the “F” (forward) or “R” (re- verse) shift indicator is displayed. When the “N” (neutral) shift indicator is displayed, the forward and reverse thrust are balanced to help keep the watercraft from moving in ei-
ther direction, although some movement may occur.
      0 13.6V
MPH
x100 RPM
100% N
   1
  
 
 
1 “N” (Neutral position)
To avoid rear-end collisions while operat- ing the watercraft, check behind you be- fore using the RiDE lever to slow down or stop the watercraft. Make sure that there are no obstacles or people behind you be- fore shifting into reverse.
Keep away from the intake grate while the engine is on. Items such as long hair, loose clothing, or PFD straps can become entan- gled in moving parts, resulting in severe in- jury or drowning.
Never insert any object into the jet thrust nozzle while the engine is running. Severe injury or death could result from coming in contact with the rotating parts of the jet pump.
1 Intake grate
2 Jet thrust nozzle
  2 1
  16
]]></page><page Index="23" isMAC="true"><![CDATA[  Stop the engine and remove the clip from the engine shut-off switch before removing any debris or weeds, which may have col- lected around the jet intake.
EJU30947
Wakeboarding and water-
skiing
You can use the watercraft for wakeboarding or water-skiing if it has the seating capacity to carry the operator, a rearward-facing spotter, and the wakeboarder or water-skier when he or she is not being pulled.
The watercraft must also have a cleat de- signed to pull a ski rope; do not attach the rope to any other location.
Safety information
   2
   1
   1
      1 Clip
2 Engine shut-off switch
1 Cleat
It is the watercraft operator’s responsibility to be alert to the safety of the wakeboarder or water-skier and others. Know and follow all state and local regulations in effect for the waters in which you will be operating.
The operator should be comfortable carrying passengers before attempting to pull a wake- boarder or water-skier.
The following are some important consider- ations for minimizing risks while pulling a wakeboarder or water-skier.
  The wakeboarder or water-skier should wear an approved PFD, preferably a bright- ly colored one so boat operators can see the person being pulled.
  The wakeboarder or water-skier should wear protective clothing. Severe internal in- juries can occur if water is forced into body cavities as a result of falling into the water.
17
]]></page><page Index="24" isMAC="true"><![CDATA[Safety information
Normal swimwear does not adequately protect against forceful water entry into the rectum or vagina. The person being pulled should wear a wetsuit bottom or clothing that provides equivalent protection.
  A second person should be on board as a spotter to watch the wakeboarder or wa- ter-skier; in most states it is required by law. Let the person being pulled direct the operator’s control of speed and direction with hand signals.
The spotter should sit astride the rear of the seat and hold onto the handgrip with both feet firmly on the floor of the footwell for proper balance while facing to the rear to watch the wakeboarder’s or water-skier’s hand signals and condition.
1 Handgrip
er’s or water-skier’s ability, as well as water
and weather conditions.
  When preparing to pull a wakeboarder or
water-skier, operate the watercraft at the slowest possible speed until the watercraft is well away from the person being pulled and slack in the ski rope is taken up. Make sure that the rope is not looped around anything.
After checking that the wakeboarder or wa- ter-skier is ready and that there is no traffic or other obstacles, apply enough throttle to raise the person.
  Make smooth, wide turns. The watercraft is capable of very sharp turns, which could exceed the abilities of the wakeboarder or water-skier. Keep the person being towed at least 50 m (164 ft), about twice the dis- tance of a standard ski rope, away from any potential hazard.
  The operators of boats and other water- craft may not be aware that you are pulling a wakeboarder or water-skier. Together with the spotter, pay attention to others around you and cruise at safe speeds.
  Be alert to the hazard of the ski rope handle snapping back at the watercraft when the wakeboarder or water-skier falls or is un- able to get up.
  Towing heavy or bulky objects other than wakeboarders or water-skiers, such as an- other boat or watercraft, can cause loss of steering control and create a hazardous condition. If you must tow another boat in an emergency situation, operate slowly and cautiously.
  1
   1
     1 Handgrip
  Your control while pulling a wakeboarder or
water-skier is affected by the wakeboard-
18
]]></page><page Index="25" isMAC="true"><![CDATA[ EJU30962
Rules of the Road
Your Yamaha watercraft is legally consid- ered a powerboat. Operation of the water- craft must be in accordance with the rules and regulations governing the waterway on which it is used.
Just as there are rules that apply when you are driving on streets and highways, there are waterway rules that apply when you are oper- ating your watercraft. These rules are used internationally, and are also enforced by the United States Coast Guard and local agen- cies. You should be aware of these rules, and follow them whenever you encounter another vessel on the water.
Several sets of rules prevail according to geographic location, but are all basically the same as the International Rules of the Road. The rules presented here in this owner’s/op- erator’s manual are condensed, and have been provided for your convenience only. Consult your local U.S. Coast Guard Auxiliary or Department of Motor Vehicles for a com- plete set of rules governing the waters in which you will be operating your watercraft. Steering and sailing rules
Whenever two vessels on the water meet one another, one vessel has the right-of-way; it is called the “stand-on” vessel. The vessel that does not have the right-of-way is called the “give-way” or “burdened” vessel. These rules determine which vessel has the right-of-way, and what each vessel should do.
Stand-on vessel
The vessel with the right-of-way has the duty to continue its course and speed, except to avoid an immediate collision. When you maintain your direction and speed, the other vessel will be able to determine how best to avoid you.
Safety information
Give-way vessel
The vessel which does not have the right-of- way has the duty to take positive and timely action to stay out of the way of the stand-on vessel. Normally, you should not cross in front of the vessel with the right-of-way. You should slow down or change directions brief- ly and pass behind the other vessel. You should always move in such a way that the operator of the other vessel can see what you are doing.
The General Prudential Rule regarding the right-of-way is that if a collision appears un- avoidable, neither boat has the right-of-way. Both boats must avoid the collision.
In other words, follow the standard rules ex- cept when a collision will occur unless both vessels try to avoid each other. If that is the case, both vessels become give-way ves- sels.
Rules when encountering vessels
There are three main situations that you may encounter with other vessels which could lead to a collision unless the Steering Rules are followed:
Meeting: you are approaching another vessel head-on
Crossing: you are traveling across another vessel’s path
Overtaking: you are passing or being passed by another vessel
In the following illustration, your watercraft is in the center. You should give the right-of- way to any vessels shown in the white area (you are the give-way vessel). Any vessels in the shaded area must yield to you (they are the give-way vessels). Both you and the
19
]]></page><page Index="26" isMAC="true"><![CDATA[Safety information
meeting vessel must alter course to avoid each other.
rection, provided the other vessel gives you the right-of-way as it should.
Overtaking
If you are passing another vessel, you are the give-way vessel. This means that the other vessel is expected to maintain its course and speed. You must stay out of its way until you are clear of it. Likewise, if another vessel is passing you, you should maintain your speed and direction so that the other vessel can steer itself around you.
Other special situations
There are three other rules you should be aware of when riding your watercraft around other vessels.
Narrow channels and bends
When navigating in narrow channels, you should keep to the right when it is safe and practical to do so. If the operator of a power- driven vessel is preparing to go around a bend that may obstruct the view of other wa- ter vessels, the operator should sound a pro- longed blast of four to six seconds on the whistle. If another vessel is around the bend, it too should sound the whistle. Even if no re- ply is heard, however, the vessel should still proceed around the bend with caution. If you navigate such waters with your watercraft, you will need to carry a portable air horn, available from local marine supply stores.
   Meeting
If you are meeting another power-driven ves- sel head on, and are close enough to run the risk of collision, neither of you has the right- of-way. Both of you should alter course to avoid an accident. You should keep the other vessel on your port (left) side. This rule does not apply if both of you will clear one another if you continue on your set course and speed.
 Crossing
When two power-driven vessels are crossing each other’s path close enough to run the risk of collision, the vessel which has the other on the starboard (right) side must keep out of the way of the other. If the other vessel is on your starboard (right) side, you must keep out of its way; you are the give-way vessel. If the other vessel is on your port (left) side, remem- ber that you should maintain course and di-
20
]]></page><page Index="27" isMAC="true"><![CDATA[ Fishing vessel right-of-way
All vessels fishing with nets, lines, or trawls are considered to be “fishing vessels” under the International Rules. Vessels with trolling lines are not considered fishing vessels. Fish- ing vessels have the right-of-way regardless of position. Fishing vessels cannot, however, impede the passage of other vessels in nar- row channels.
Sailing vessel right-of-way
Sailing vessels should normally be given the right-of-way. The exceptions to this are:
(1) When the sailing vessel is overtaking the
power-driven vessel, the power-driven
vessel has the right-of-way.
(2) Sailing vessels should keep clear of any
fishing vessel.
(3) In a narrow channel, a sailing vessel
should not hamper the safe passage of a power-driven vessel that can navigate only in such a channel.
Reading buoys and other markers
The waters of the United States are marked for safe navigation by the lateral system of buoyage. Simply put, buoys and markers have an arrangement of shapes, colors, num- bers, and lights to show which side of the buoy a boater should pass on when navigat- ing in a particular direction. The markings on these buoys are oriented from the perspec- tive of being entered from seaward (the boat- er is going towards the harbor). Red buoys are passed on your starboard (right) side when proceeding from open water into the harbor, and black buoys are to your port (left) side. An easy way to remember the meaning of the colors is the phrase “red right return- ing”. When navigating out of the harbor, your position with respect to the buoys should be reversed; red buoys should be to port and black buoys to starboard.
Safety information
Many bodies of water used by boaters are entirely within the boundaries of a particular state. The Uniform State Waterway Marking System has been devised for these waters. This system uses buoys and signs with dis- tinctive shapes and colors to show regulatory or advisory information. These markers are white with black letters and orange borders.
21
]]></page><page Index="28" isMAC="true"><![CDATA[Safety information
They signify speed zones, restricted areas, danger areas, and general information.
                                        Remember, markings may vary by geograph- ic location. Always consult local boating au- thorities before riding your watercraft in unfamiliar waters.
22
]]></page><page Index="29" isMAC="true"><![CDATA[EJU30983
To get more boating safety
information
Be informed about boating safety. Additional publications and information can be obtained from many organizations, including the fol- lowing.
United States Coast Guard
Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer Af- fairs
U.S. Coast Guard Headquarters Washington, D.C. 20593-0001 http://www.uscgboating.org/
Other sources
You can find local rules by contacting the Na- tional Association of State Boating Law Ad- ministrators, or your local Power Squadron. Watercraft Education and Training
The Online Boating Safety Course, available through the watercraft section of the yama- ha-motor.com website, is a free, 50 question learning course available to the public. Upon successful completion of 80 percent or bet- ter, the user can request a certificate of com- pletion by mail or can download one immediately. The Online Boating Safety Course, provided by the Boat/US Founda- tion, is approved by the National Association of State Boating Law Administrators (NASB- LA) and recognized by the United States Coast Guard. This course meets the educa- tion requirement for those states that recog- nize non-proctored, NASBLA-approved courses.
Yamaha is the watercraft industry’s leading manufacturer to build awareness and sup- port for boating education. In 1997, Yamaha launched its GET W.E.T. (Watercraft Educa- tion and Training) initiative and has since reached out to over one million Americans promoting the benefits of boating education.
The Online Boating Safety Course: http://www.boatus.org/
Safety information
   23
]]></page><page Index="30" isMAC="true"><![CDATA[Safety information
 EJU30992
When you ride responsibly, with respect and courtesy for others, you help ensure that our waterways stay open for the enjoyment of a variety of recreational opportunities.
Enjoy your watercraft
responsibly
You share the areas you enjoy when riding your watercraft with others and with nature. So your enjoyment includes a responsibility to treat these other people, and the lands, waters, and wildlife with respect and courte- sy.
Whenever and wherever you ride, think of yourself as the guest of those around you. Remember, for example, that the sound of your watercraft may be music to you, but it could be just noise to others. And the exciting splash of your wake can make waves others won’t enjoy.
Avoid riding close to shoreline homes and waterfowl nesting areas or other wildlife ar- eas, and keep a respectful distance from fish- ermen, other boats, swimmers, and populated beaches. When travel in areas like these is unavoidable, ride slowly and obey all laws.
Proper maintenance is necessary to ensure that the exhaust emission and sound levels of your watercraft will continue to be within reg- ulated limits. You have the responsibility to make sure that the recommended mainte- nance in this owner’s/operator’s manual is carried out.
Remember, pollution can be harmful to the environment. Do not refuel or add oil where a spill could cause damage to nature. Remove your watercraft from the water and move it away from the shoreline before refueling. Dis- pose of water and any fuel and oil residue in the engine compartment according to local regulations. And keep your surroundings pleasant for the people and wildlife that share the waterways: don’t litter.
24
]]></page><page Index="31" isMAC="true"><![CDATA[Trolling speed
Watercraft glossary
“Trolling” is the lowest maneuvering speed. You are applying little or no throttle. The water- craft is down in the water, and there is no wake.
Sub-planing speed
“Sub-planing” is a medium speed. The bow of the watercraft is slightly up from the water sur- face, but you are still traveling through the water. There is a wake.
Planing speed
“Planing” is a faster speed. The watercraft is more level and is skimming on top of the water. There is a wake.
Bow
The front end of the watercraft.
Stern
The rear end of the watercraft.
Starboard
The right side of the watercraft when facing forward.
Port
The left side of the watercraft when facing forward.
Bilge water
Water that has collected in the engine compartment.
Yamaha Engine Management System (YEMS)
YEMS is an integrated, computerized management system that controls and adjusts ignition timing, fuel injection, engine diagnostics, and the off-throttle steering (OTS) system. Reverse with Intuitive Deceleration Electronics (RiDE)
RiDE is an electronic system that controls the reverse, neutral, and deceleration operations of the watercraft.
Description
 EJU43331
25
]]></page><page Index="32" isMAC="true"><![CDATA[Description
EJU31012
Exterior
Location of main components
  12345
                              76
89
                                                     11
10
26
1 Hood
2 Beverage holder (page 60)
3 Pull-up cleat (FX CRUISER SVHO / FX
LIMITED SVHO) (page 57)
4 Footwell
5 Pull-up cleat (FX LIMITED SVHO) (page 57)
6 Optional part mounting bracket
7 Fuel filler cap (page 62)
8 Front seat (page 54)
9 Rear seat (page 54)
10 Cooling water pilot outlet (page 34) 11 Bow eye (page 56)
]]></page><page Index="33" isMAC="true"><![CDATA[ Description
  1
2
3 13 4
5
                                12
                66 88
        11 10 9
7
     1 Handgrip (page 55)
2 Cleat (page 56)
3 Stern storage compartment (page 59) 4 Reboarding grip (page 55)
5 Boarding platform
6 Stern eye (page 56)
7 Intake grate
8 Stern drain plug (page 66)
9 Ride plate
10 Jet thrust nozzle
11 Reverse gate (page 35)
12 Reboarding step (page 55)
13 Flushing hose connector (page 91)
27
]]></page><page Index="34" isMAC="true"><![CDATA[Description
      349
8
7
22
11
           65
                   20
17 19 18 16
10 11
14 13 12
15
 1 Handlebar
2 Rearview mirror
3 RiDE lever (page 35)
4 Start switch (page 31)
5 Engine shut-off switch (page 31)
6 Clip (page 31)
7 Engine shut-off cord (lanyard) (page 31)
8 Multifunction information center (page 45)
9 Throttle lever (page 32)
10 “SPEED CONTROL” up switch (page 39, 40, 43)
11 “SPEEDCONTROL”downswitch(page39, 40, 43)
12 “SET” switch (page 43)
13 “NO-WAKE MODE” switch (page 40)
14 Tilt lever (page 33)
15 Glove compartment (page 58)
16 “ALARM MUTE” button (page 46)
17 “MENU SCROLL” button (page 46)
18 Engine stop switch (page 31)
19 “TRIM/T.D.E.” down switch (page 37, 39) 20 “TRIM/T.D.E.” up switch (page 37, 39)
28
]]></page><page Index="35" isMAC="true"><![CDATA[  Engine compartment
1 Dipstick (page 64)
2 Engine oil filler cap (page 64)
3 Electrical box
4 Battery (page 72)
5 Removable watertight storage compart- ment (page 60)
6 Spark plug/Ignition coil
7 Fuel tank
8 Water separator (page 34)
9 Air filter case
10 Engine cover
Description
        34
     12
                       10 9
 8 7
65
         29
]]></page><page Index="36" isMAC="true"><![CDATA[ Control function operation
 EJU31026
Watercraft control functions
EJU45090
Yamaha Security System
The Yamaha Security System functions to help prevent unauthorized use or theft of the watercraft. The lock and unlock modes of the security system can be selected using the engine lock screen of the multifunction infor- mation center. The engine cannot be started if the lock mode of the security system is se- lected. The engine can only be started if the unlock mode is selected.
TIP:
The Yamaha Security System setting can
only be selected while the engine is stopped. EJU45100
Yamaha Security System setting
The Yamaha Security System setting can be confirmed by the lock or unlock mode indica- tor on the multifunction information center.
1 2
1 Lock mode indicator
2 Unlock mode indicator
To select the lock or unlock mode of the Yamaha Security System:
(1) Stop the engine.
TIP:
If the multifunction information center is turned off because the engine is stopped, perform one of the following operations to turn on the center without starting the engine.   Push the start switch briefly.
 While pushing the engine stop switch, push the start switch.
(2) Tap the lock or unlock mode indicator on the multifunction information center.
(3) Flick up or down to set each digit of the
4-digit PIN, and then tap the “Enter” but- ton.
 Enter PIN
9999 0000 1111
Enter
  TIP:
The default setting for the PIN is “1234”. The PIN can also be changed. (See page 49 for in- formation on changing the PIN.)
(4)
Tap “ON” to select the lock mode of the Yamaha Security System or tap “OFF” to select the unlock mode, and then tap “Save”.
     Engine Lock
 ON
OFF
  Save
    30
(5)
The beeper sounds once when the lock mode of the Yamaha Security System is selected and two times when the unlock mode is selected, and the multifunction information center returns to the home screen.
]]></page><page Index="37" isMAC="true"><![CDATA[Control function operation
 EJU31153
Engine stop switch “ ”
The engine stop switch (red button) stops the engine when the switch is pushed.
vent accidental starting or unauthorized op- eration by children or others.
     1
1 Engine stop switch
EJU31164
Engine shut-off switch “ ”
The engine shut-off switch automatically stops the engine when the clip, on the end of the engine shut-off cord (lanyard), is removed from the switch, such as if the operator falls off the watercraft.
Insert the clip under the engine shut-off switch before starting the engine.
EJU42323
Start switch “ ”
ECJ01311
Do not run the engine over 4000 r/min on land. Also, do not run the engine for more than 15 seconds without supplying water, otherwise the engine could overheat.
The start switch (green button) starts the en- gine when the switch is pushed.
Release the start switch as soon as the en- gine starts to run. If the engine does not start in 5 seconds, release the start switch, wait 15 seconds, and then try again. NOTICE: Never push the start switch while the engine is running. Do not operate the start switch for more than 5 seconds, otherwise the battery will be discharged and the engine
     1
2
  3
1 Engine shut-off switch
2 Clip
3 Engine shut-off cord (lanyard)
When the engine is not running, remove the clip from the engine shut-off switch to pre-
31
]]></page><page Index="38" isMAC="true"><![CDATA[Control function operation
 will not start. Also, the starter motor could be damaged. [ECJ01041]
EJU43342
RiDE lever
When the RiDE lever is squeezed, the reverse gate lowers and the watercraft starts moving in reverse. If the watercraft is moving forward, the watercraft gradually slows down until it stops, and then the watercraft starts moving in reverse.
 1
   1
  1 Start switch
The engine will not start under any of the fol- lowing conditions:
  Lock mode of the Yamaha Security System
has been selected. (See page 30 for Yamaha Security System setting proce- dures.)
  Clip is removed from the engine shut-off switch.
  Throttle lever is squeezed.
  Throttle lever is malfunctioning.
  RiDE lever is squeezed.
  RiDE lever is malfunctioning.
EJU31212
Throttle lever
The throttle lever increases the engine speed
when the lever is squeezed.
1 RiDE lever
When the RiDE lever is released, it automati- cally returns to its fully closed (idle) position and the reverse gate moves to the neutral po-
sition.
EJU31262
Steering system
By turning the handlebars in the direction you
wish to travel, the angle of the jet thrust noz-
 1
 1 Throttle lever
The throttle lever returns automatically to its
fully closed (idle) position when released. 32
]]></page><page Index="39" isMAC="true"><![CDATA[zle is changed, and the direction of the water- craft is changed accordingly.
EJU31294
Adjustable tilt steering system
The position of the handlebars can be adjust- ed back and forth by operating the tilt lever. To adjust the handlebar position:
(1) Pull the tilt lever up to disengage the han-
dlebar lock, and then move the handle- bars back or forth to the desired position. WARNING! Never pull the tilt lever dur- ing operation, otherwise the handle- bars may suddenly change position, which may lead to an accident. [EWJ00042]
Control function operation
  1
              2
      1
    1 Handlebar
2 Jet thrust nozzle
Since the strength of the jet thrust determines the speed and degree of a turn, throttle must always be applied when attempting a turn, except at trolling speed.
This model is equipped with the Yamaha En- gine Management System (YEMS) that in- cludes an off-throttle steering (OTS) system. It will activate at planing speeds should you attempt to steer the watercraft after releasing the throttle lever. The OTS system assists in turning by continuing to supply some thrust while the watercraft is decelerating, but you can turn more sharply if you apply throttle while turning the handlebars. The OTS sys- tem does not function below planing speeds or when the engine is off. Once the engine slows down, the watercraft will no longer turn in response to handlebar input until you apply throttle again or you reach trolling speed.
1 Tilt lever
         33
]]></page><page Index="40" isMAC="true"><![CDATA[ Control function operation
(2) Make sure that the tilt lever returns to its original position and that the handlebars are securely locked in place.
          EJU41801
Cooling water pilot outlets
When the engine is running, some of the cooling water that is circulated in the engine is discharged from the cooling water pilot outlets.
TIP:
  It will take about 60 seconds for the water to reach the outlets after the engine is start- ed.
  Water discharge may not be constant when the engine is running at idling speed. If this occurs, apply a little throttle to make
sure that water discharges properly. EJU40323
Water separator
The water separator prevents water from en- tering the fuel tank by collecting any water that has entered the fuel tank breather hose if the watercraft was capsized.
If water has collected in the water separator, drain it by loosening the drain screw.
        1 2
             1
          1 Cooling water pilot outlet (port [left] side)
There are cooling water pilot outlets on the port (left) and starboard (right) sides of the watercraft. To check for proper operation of the cooling system, make sure that water is being discharged from the port (left) pilot out- let. If water is not being discharged from the outlet, stop the engine and check the jet in- take for clogging. (See page 105 for informa- tion on the jet intake.)
1 Water separator 2 Drain screw
To drain water from the water separator:
(1) Place a drain pan or dry cloth under the
water separator.
(2) Gradually loosen the drain screw to drain
the water. Catch the draining water in the drain pan or soak it up with the dry cloth so that it does not spill into the engine compartment. If any water spills into the watercraft, be sure to wipe it up with a dry cloth.
(3) Securely tighten the drain screw until it stops.
34
]]></page><page Index="41" isMAC="true"><![CDATA[ EJU40014
Watercraft operation functions
EJU43154
Shift system
EWJ01773
  Make sure that there are no obstacles or people behind you before shifting into reverse.
  Do not touch the reverse gate while the RiDE lever is being operated, otherwise you could be pinched.
  If the RiDE lever and throttle lever are being operated at the same time, do not release only the RiDE lever. Otherwise, the watercraft could accelerate more quickly than expected, which may lead to an accident.
The RiDE lever and throttle lever can be oper- ated to change the forward or rearward movement of the watercraft only when the engine is running. When the RiDE lever is squeezed, the reverse gate lowers and de- flects the water jet being discharged from the jet thrust nozzle so that the watercraft moves in reverse or is in neutral. When the throttle le- ver is squeezed, the reverse gate rises and the watercraft moves forward.
TIP:
  This model is equipped with a function which limits the engine speed in reverse.
  When the engine is started, the reverse
gate automatically moves to the neutral po-
sition.
To shift into reverse:
(1) Release the throttle lever.
(2) Squeeze the RiDE lever. The reverse
gate will lower, the engine speed will in- crease, the watercraft will start moving in
Watercraft operation
reverse, and the “R” (reverse) shift indi- cator will be displayed.
 1
    1 RiDE lever
   1
2
 1 Reverse gate
2 Reverse position
      0 13.6V
MPH
x100 RPM
100% R
   1
 1 “R” (Reverse position)
To shift into neutral from reverse:
Release the RiDE lever. The reverse gate will automatically return to the neutral position
  35
]]></page><page Index="42" isMAC="true"><![CDATA[Watercraft operation
and the “N” (neutral) shift indicator will be dis- played.
To shift into forward:
(1) Release the RiDE lever.
(2) Squeeze the throttle lever. The reverse
gate will rise completely, the engine speed will increase, the watercraft will start moving forward, and the “F” (for- ward) shift indicator will be displayed.
   1
   1
 1 RiDE lever
   1
2
   1
2
1 Reverse gate
2 Neutral position
1 Throttle lever
       0 13.6V
MPH
x100 RPM
100% N
   1
 1 Reverse gate
2 Forward position
     0 13.6V
MPH
x100 RPM
100% F
   1
 1 “N” (Neutral position)
TIP:
Although the neutral position helps keep the watercraft from moving even when the en- gine is running, some movement may occur.
1 “F” (Forward position)
36
]]></page><page Index="43" isMAC="true"><![CDATA[ TIP:
Watercraft operation
This function can be used only for forward operation of the watercraft.
If the RiDE lever is squeezed while the throttle
lever is squeezed, the watercraft will slow TIP:
down, and once stopped, move in reverse. To shift into neutral from forward:
(1) Release the throttle lever.
(2) Lightly squeeze and release the RiDE le-
ver. The “N” (neutral) shift indicator will be displayed.
  When the watercraft is moving in reverse or is in neutral, the jet thrust nozzle will auto- matically change to the neutral trim setting. When the watercraft is shifted into forward, the jet thrust nozzle will automatically change to the selected trim setting.
  While the watercraft is in neutral, the “TRIM/T.D.E.” switches control the forward and reverse operation of the T.D.E. (thrust direction enhancer). (See page 39 for infor- mation on the T.D.E.)
  The watercraft performance characteristics according to the trim angle change de- pending on the operating conditions.
Confirming the trim setting
The trim setting can be confirmed by the trim setting indicator and trim setting level on the multifunction information center.
         0 13.6V
MPH
x100 RPM
100% N
   1
  21
     +2 13.6V
MPH
x100 RPM
100% F
     1 “N” (Neutral position)
TIP:
If the RiDE lever is squeezed continuously,
the reverse gate will move to the reverse po-
sition.
EJU45041
Electric trim system
The electric trim system is a function for changing the vertical angle of the jet thrust nozzle to change the trim angle and perfor- mance characteristics of the watercraft.
1 Trim setting indicator 2 Trim setting level
To change the trim setting:
(1) Shift into forward.
(2) Push the “TRIM/T.D.E.” up switch to in-
crease the trim setting and raise the bow, or push the “TRIM/T.D.E.” down switch to decrease the trim setting and lower
 37
]]></page><page Index="44" isMAC="true"><![CDATA[Watercraft operation
the bow. The trim angle can be adjusted in the range of the trim settings –2 to +2.
Vertical movement of the bow will be reduced and the watercraft will get up on plane more quickly when accelerating.
     1
2
    -2
1 “TRIM/T.D.E.” up switch
2 “TRIM/T.D.E.” down switch
Bow-up positions
The bow will go up, causing the trim angle to increase.
There is less water resistance, therefore, straight-ahead acceleration is enhanced.
   +2
 Bow-down positions
The bow will go down, causing the trim angle to decrease.
38
]]></page><page Index="45" isMAC="true"><![CDATA[ EJU40002
Watercraft operation modes
EJU45061
Reverse assist
The reverse assist is a function for temporar- ily increasing the engine speed when moving in reverse, such as to enter the water smoothly when launching the watercraft from a trailer.
This function operates after the engine is started and only if the watercraft is not shifted into forward.
TIP:
Once the watercraft is shifted into forward af- ter the engine is started, the reverse assist cannot be operated.
Activating and deactivating the reverse assist
The activation of the reverse assist can be confirmed by the reverse assist indicator on the multifunction information center.
Watercraft operation
increase. The engine speed can be ad- justed to two levels: +1 and +2.
 1
  1 RiDE lever
     1 2
            MPH
x100 RPM
 0 Reverse Assist
100% R
  13.6V
12
+2
     1 Reverse assist indicator 2 Reverse assist level
To activate the reverse assist:
(1) Start the engine.
(2) Squeeze the RiDE lever to the fully open
position, and then push the “SPEED CONTROL” up switch. Once the beeper sounds once and the reverse assist indi- cator is displayed, the engine speed will
1 “SPEED CONTROL” up switch
2 “SPEED CONTROL” down switch
To deactivate the reverse assist:
Perform one of the following operations. The beeper sounds two times and the reverse as- sist indicator disappears when the reverse assist is deactivated.
  Relax your grip on the RiDE lever.
  Push the “SPEED CONTROL” down switch
when the reverse assist level is set to +1.
  Squeeze the throttle lever.
EJU45071
T.D.E. (thrust directional enhancer)
The T.D.E. is a function for slightly lifting or lowering the reverse gate from the neutral po- sition to operate the watercraft at very low speeds when the engine is running at idling speed.
 39
]]></page><page Index="46" isMAC="true"><![CDATA[Watercraft operation
 This function can be used only when the wa- tercraft is in neutral.
TIP:
While the watercraft is shifted into forward, the “TRIM/T.D.E.” switches control the elec- tric trim system. (See page 37 for information on the electric trim system.)
Activating and deactivating the T.D.E.
TheactivationoftheT.D.E.canbeconfirmed by the T.D.E. indicator on the multifunction information center.
TIP:
While the T.D.E. is activated, the “N” (neutral) shift indicator will be displayed and “0” will be displayed on the speedometer.
To deactivate the T.D.E.:
Perform one of the following operations. The T.D.E. indicator disappears and the T.D.E. is deactivated.
 Squeezethethrottlelever.
  Squeeze the RiDE lever.
  Push and hold the “NO-WAKE MODE”
switch.
  While moving forward at a very low speed,
push the “TRIM/T.D.E.” down switch.
  While moving in reverse at a very low
speed, push the “TRIM/T.D.E.” up switch.
TIP:
The T.D.E. is also deactivated when the en-
gine is stopped. EJU45051
No-wake mode
The no-wake mode is a function that main- tains the engine speed at a fixed setting for operating the watercraft at low speeds. While the watercraft is operating in no-wake mode, the engine speed can be adjusted to one en- gine speed each above and below the initial engine speed.
This function can be used only when the wa- tercraft is in neutral, or when the watercraft is shifted into forward and the engine is operat- ing at idling speed.
TIP:
If the no-wake mode is activated when the watercraft is in neutral, the watercraft will au- tomatically shift into forward and the water- craft will start moving at a low speed.
   2
   3
T.D.E. FORWARD T.D.E. REVERSE
MPH
x100 RPM
  0 13.6V
100% N
T.D.E. FORWARD
   1
  1 T.D.E. indicator
2 Forward operation at a very low speed 3 Reverse operation at a very low speed
To activate the T.D.E.:
(1) Shift into neutral.
(2) Push the “TRIM/T.D.E.” up switch to
move forward at a very low speed or push the “TRIM/T.D.E.” down switch to move in reverse at a very low speed.
     1
2
40
1 “TRIM/T.D.E.” up switch
2 “TRIM/T.D.E.” down switch
]]></page><page Index="47" isMAC="true"><![CDATA[  Activating and deactivating the no-wake mode
The activation of the no-wake mode can be confirmed by the no-wake mode indicator on the multifunction information center.
Watercraft operation
tings: “No Wake –1”, “No Wake” (stan-
dard setting), and “No Wake +1”.
To deactivate the no-wake mode:
Perform one of the following operations. The beeper sounds two times and the no-wake mode indicator disappears when the no- wake mode is deactivated.
  Push the “NO-WAKE MODE” switch.
  Squeeze the throttle lever.
  Squeeze the RiDE lever.
TIP:
The no-wake mode is also deactivated when
the engine is stopped. EJU45031
Drive control mode
The drive control mode is a function for set- ting the maximum watercraft speed and ac- celeration for stable towing and to support inexperienced operators.
The maximum watercraft speed can be se- lected from three settings and the accelera- tion can be selected from two settings.
TIP:
The watercraft speed setting is a target value. The actual watercraft speed may vary de- pending on the operating conditions. Activating the drive control mode Activation of the drive control mode can be confirmed by the drive control mode indica- tor on the multifunction information center. When the drive control mode is activated, the drive control mode indicator is shown in light blue.
1
1 Drive control mode indicator
To activate the drive control mode:
(1) Release the throttle lever and let the en-
gine speed return to idle.
       0 No Wake
100% F
MPH
   13.6V
x100 RPM
+1
  12
1 No-wake mode indicator 2 No-wake mode level
To activate the no-wake mode:
(1) Shift into neutral, or release the throttle
lever and let the engine speed return to
idle.
(2) Push and hold the “NO-WAKE MODE”
switch. Once the beeper sounds three times and the no-wake mode indicator is displayed, the no-wake mode is activat- ed.
1
2 3
1 “NO-WAKE MODE” switch
2 “SPEED CONTROL” up switch
3 “SPEED CONTROL” down switch
(3) Push the “SPEED CONTROL” up switch or “SPEED CONTROL” down switch to adjust the engine speed to three set-
                41
]]></page><page Index="48" isMAC="true"><![CDATA[ Watercraft operation
(2) Tap the drive control mode indicator on the multifunction information center.
(3) If the drive control mode screen is
locked, the PIN entry screen will be dis- played. Flick up or down to set each digit of the 4-digit PIN, and then tap the “En- ter” button. If the drive control mode screen is not locked, the screen shown in step 4 will be displayed.
Enter
(4) Tap the “ON” button. Once the beeper sounds three times and “ ” is displayed in light blue, the drive control mode is ac- tivated.
To operate the watercraft using the drive con- trol mode:
(1) Release the throttle lever and let the en-
gine speed return to idle.
(2) Activate the drive control mode.
(3) Squeeze the throttle lever. The water-
craft will accelerate according to the se- lected acceleration setting up to the selected maximum watercraft speed set- ting.
TIP:
If the throttle lever is squeezed to a level less than the selected acceleration setting, the watercraft will accelerate according to the throttle lever operation instead of the select- ed acceleration setting.
Selecting the drive control mode settings
The drive control mode settings for the max- imum watercraft speed and acceleration are saved. In addition, the activation and settings of the drive control mode can be locked to prevent others from changing them.
When the drive control mode is locked, a PIN must be entered to operate the drive control mode screen.
To select the maximum watercraft speed and acceleration settings:
(1) Perform steps 1–3 in “To activate the drive control mode”.
(2) Tap the “Settings” button.
(3) Flick up or down to select the maximum
watercraft speed setting under “Speed”
    Enter PIN
9999 0000 1111
   Drive Control ON OFF
Settings Lock
       To deactivate the drive control mode:
(1) Perform steps 1–3 in “To activate the
drive control mode”.
(2) Tap the “OFF” button. The beeper
sounds two times and “ ” is displayed in black when the drive control mode is deactivated.
 42
]]></page><page Index="49" isMAC="true"><![CDATA[  and the acceleration setting under “Ac- cel.”
12
Save
1 Maximum watercraft speed setting 2 Acceleration setting
(4) Tap the “Save” button to complete the settings and return to the previous dis- play.
To lock the drive control mode screen:
(1) Release the throttle lever and let the en-
gine speed return to idle.
(2) Tap the drive control mode indicator on
the multifunction information center.
(3) Tap the “Lock” button.
(4) The PIN entry screen will be displayed.
Watercraft operation
To unlock the drive control mode screen:
(1) Release the throttle lever and let the en-
gine speed return to idle.
(2) Tap the drive control mode indicator on
the multifunction information center.
(3) The PIN entry screen will be displayed. Flick up or down to set each digit of the 4-digit PIN, and then tap the “Enter” but-
ton.
(4) Tap the “Lock” button.
(5) Tap the “OFF” button.
(6) Tap the “Save” button to complete the
setting and return to the “Drive Control”
screen. EJU45021
Cruise assist
The cruise assist is a function for maintaining a desired engine speed within a fixed range while operating the watercraft. Once the cruise assist is activated, the set engine speed can be increased or decreased. How- ever, the adjustment is limited to a maximum of five increments above or below the initial cruise assist setting.
TIP:
The cruise assist can only be set between en- gine speeds of approximately 3000 r/min and approximately 7000 r/min.
  Speed
45 MPH 35 MPH 55 MPH
 Accel.
Slow Normal Slow
   Flick up or down to set each digit of the 4-digit PIN, and then tap the “Enter” but- ton.
(5) Tap the “ON” button.
 Drive Control Lock
   ON
OFF
  Save
(6) Tap the “Save” button to complete the setting and return to the “Drive Control” screen.
43
]]></page><page Index="50" isMAC="true"><![CDATA[ Watercraft operation
Activatinganddeactivatingthecruiseas- sist
Activation of the cruise assist can be con- firmed by the cruise assist indicator on the multifunction information center.
squeezed further than the position at which the cruise assist was set.
TIP:
Check the multifunction information center to make sure that the cruise assist is activated before squeezing the throttle lever to the full throttle position. If the cruise assist is not ac- tivated, the engine will respond normally to the throttle operation.
(4) Once the cruise assist is activated, push the “SPEED CONTROL” up switch to in- crease the set engine speed or the “SPEED CONTROL” down switch to de- crease the set engine speed. The engine speed can be changed in the range of the cruise assist levels –5 to +5.
TIP:
Because the cruise assist can only be set be- tween engine speeds of approximately 3000 r/min and approximately 7000 r/min, the cruise assist level cannot be adjusted to an engine speed outside of this range.
To deactivate the cruise assist:
Relax your grip on the throttle lever past the position at which the cruise assist was set. The beeper sounds two times and the cruise assist indicator disappears when the cruise assist is deactivated.
        MPH
0 Cruise Assist     100%
 13.6V
x100 RPM
F
+4
   12
1 Cruise assist indicator 2 Cruise assist level
To activate the cruise assist:
(1) Operate the throttle lever until the de-
sired engine speed is reached.
(2) When the engine speed reaches the de- sired cruise assist setting, push the “SET” switch. Once the beeper sounds three times and the cruise assist indica- tor is displayed, the cruise assist is acti-
  vated.
    1 2
3
         1 “SPEED CONTROL” up switch
2 “SPEED CONTROL” down switch
3 “SET” switch
(3) When the cruise assist is activated, slow- ly squeeze the throttle lever to keep it
44
]]></page><page Index="51" isMAC="true"><![CDATA[  EJU45110
Multifunction information
center
The multifunction information center displays various watercraft information.
The multifunction information center is a touch screen that you can touch directly to turn the various functions on or off or change settings.
In addition, the language and display units shown can be changed. (See page 49 for in- formation on changing the language and dis- play units.) In the illustrations in this manual, English is used for the language and US units are used for the display units.
EWJ01980
For safety, do not touch the multifunction information center while the watercraft is moving. Otherwise, you could lose control of the watercraft, which may lead to an ac- cident.
TIP:
The multifunction information center does not receive operation input while the watercraft is moving. Before operating the multifunction information center, stop the watercraft and check the area around you to make sure it is safe to operate the center.
Turning on the multifunction information center
When the start switch is pushed, the multi- function information center turns on. After the logo display appears for a few seconds, the home screen is displayed and the touch screen can be operated by touching it.
TIP:
Perform one of the following operations to turn on the multifunction information center without starting the engine.
  Push the start switch briefly.
Instrument operation
 While pushing the engine stop switch, push the start switch.
Turning off the multifunction information center
If the multifunction information center does not receive any operation input within 25 sec- onds after the engine stops or if 3 minutes has elapsed after the engine stops, the center turns off.
TIP:
The multifunction information center turns off 3 minutes after the engine stops even if there is operation input.
Message indicating that operation input cannot be received
If “Turn OFF Engine”, “Engine Comm Error”, or other message appears in red characters during touch operation, the operation input cannot be received because the input condi- tions are not satisfied.
Perform the operation again according to the displayed message, or stop the engine to turn off the multifunction information center, and then turn on the center again. If the mes- sage remains displayed, consult a Yamaha dealer.
Turn OFF Engine
     ON
OFF
  Save
45
]]></page><page Index="52" isMAC="true"><![CDATA[Instrument operation
EJU45121
Operation buttons
This model is equipped with operation but- tons that can be used in addition to touching the multifunction information center.
symbol in the warning bar that is displayed when a warning is activated.
 1
        0 13.6V
MPH
x100 RPM
100% N
   2
           1
2
 1 “MENU SCROLL” button 2 “ALARM MUTE” button
“MENU SCROLL” button
Each time this button is pushed, the multi- function information center switches in the following order.
Home screen → Information screen (“Trip In- fo”) → Information screen (“Fuel Info”) → Home screen
“ALARM MUTE” button
Push this button to stop the buzzer when a warning is activated. If this button is pushed again while the warning is still activated, the buzzer will start sounding again.
TIP:
  The operation sounds cannot be turned off.   If the “ALARM MUTE” button was pushed to stop the buzzer, the buzzer will start
sounding again after 5 minutes. EJU45131
Touch screen
The touch operations are enabled only for the screen tab bar, the items and sliders that are shown in the center display, and the warning
1 Screen tab bar 2 Center display
1 Warning bar
Screen tab bar
When each symbol is tapped, the watercraft information, function settings, and other in- formation are shown in the center display. (See page 47 for information on each screen.) Center display
The center display shows the watercraft in- formation, function settings, and other infor- mation according to the symbol on the screen tab bar that is tapped.
Warning bar
The warning bar is shown instead of the ta- chometer value display only when an error or malfunction is detected.
When the warning symbol is tapped, the warning description, error code, and other in- formation are shown in the center display. (See page 51 for information about the warn- ing descriptions.)
     1
 46
]]></page><page Index="53" isMAC="true"><![CDATA[Instrument operation
 EJU45141
Status area
TIP:
If a warning is activated or a malfunction is detected, the warning bar will be displayed instead of the tachometer number display. Shift indicator
This indicator shows the reverse gate shift positions: “F” (forward), “N” (neutral), and “R” (reverse). (See page 35 for shifting proce- dures.)
Fuel level meter
The fuel level meter shows the amount of fuel remaining in the fuel tank using the number of display segments and a percentage value.
If the amount of remaining fuel is less than 10%, the fuel level warning will activate and the percentage display will change to “Low”. (See page 52 for information on the fuel level warning.)
TIP:
The accuracy of the fuel level meter varies
depending on the operating conditions. Use
this function as a reference only.
EJU45151
Home screen “ ”
The center display of the home screen shows
the speedometer and the indicators for the operation modes. (See page 39 for informa- tion on the functions of the various modes.)
TIP:
If the engine speed increases while the drive control mode screen, setting menu screen, or engine lock screen is displayed, the multi-
The areas on the left and right sides of the multifunction information center that show the watercraft information and the tachome- ter at the bottom of the multifunction informa- tion center do not respond to touch operation.
15
      0 13.6V
MPH
x100 RPM
100% N
   234
 1 Trim setting indicator 2 Voltmeter
3 Tachometer
4 Shift indicator
5 Fuel level meter
Trim setting indicator
The position of this indicator and the trim set- ting level indicate the trim setting of the jet thrust nozzle. (See page 37 for information on the trim setting.)
Voltmeter
The voltmeter shows the battery voltage. When the battery voltage is normal, the volt- meter displays approximately 14 volts.
If the battery voltage has dropped or risen significantly, the battery voltage warning will activate and the voltage display will blink. (See page 52 for information on the battery voltage warning.)
Tachometer
The tachometer shows the engine speed us- ing the large number ×100 RPM (r/min) and the number of display segments.
47
]]></page><page Index="54" isMAC="true"><![CDATA[Instrument operation
function information center will automatically switch to the home screen.
Tap “Fuel Info ”, “ Trip Info”, or “ ” to switch the displayed screen.
TIP:
The display units for the distances and fuel amounts are selected according to the dis- play units of the multifunction information center. (See page 50 for information on switching the display units.)
Trip information (“Trip Info”)
  1
  MPH
 T.D.E. FORWARD
 2 3 4 5
Reverse Assist +2 T.D.E. FORWARD NoWake +1 Cruise Assist +4
  1.5 Trip Hrs 3.2 Trip Miles 8.1 Engine Hrs
Fuel Info
 1 2 3
   1 Speedometer
2 Reverse assist indicator 3 T.D.E. indicator
4 No-wake mode indicator 5 Cruise assist indicator
Speedometer
1 Trip time
2 Distance traveled 3 Total engine hours
 Item
Description
Trip time*
Shows the hours of engine operation that have elapsed since the item was last reset.
Distance trav- eled*
Shows the distance trav- eled by the watercraft since the item was last re- set.
Total engine hours
Shows the total hours of engine operation that have elapsed since the water- craft was new.
The speedometer shows the watercraft speed.
TIP:
  The display units of the speedometer are selected according to the display units of the multifunction information center. (See page 50 for information on switching the display units.)
  When operating the watercraft in reverse, or when moving forward or in reverse at a very low speed using the T.D.E., “0” will be
displayed on the speedometer. EJU45161
Information screen “ ”
The information screens show the trip infor- mation and fuel information in the center dis- play.
* Touch and hold this item to reset it.
48
]]></page><page Index="55" isMAC="true"><![CDATA[  Fuel information (“Fuel Info”)
Instrument operation
  Selecting the display language
  Displaying the time since the last mainte-
nance
  Resetting the settings, trip information, and
fuel information
 1 2 3
5.4 Av MPG 1.4 Gal Used 0.6 Gp H
Trip Info
    PIN Settings Unit Wellness
Display Language Reset
     1 Average fuel consumption per gallon or liter 2 Total fuel used
3 Fuel consumption per hour
    Item
Average fuel consumption per gallon or li- ter*
Total fuel used*
Fuel consump- tion per hour
Description
Shows the average dis- tance that was traveled by the watercraft on 1.0 gal- lon or 1.0 liter of fuel since the item was last reset.
Shows the total fuel that has been consumed by the engine in gallons or li- ters since the item was last reset.
Shows the current fuel consumption in gallons per hour or liters per hour.
Changing the PIN (“PIN Settings”)
The PIN can be changed to any 4-digit num- ber.
  PIN Settings
0000 1111 2222
Save
          * Touch and hold this item to reset it. EJU45170
Drive control mode screen “ ”
The drive control mode screen shows the setting screen for the drive control mode in the center display. (See page 41 for informa-
tion on the drive control mode.) EJU45181
Setting menu screen “ ”
The setting menu screen shows a menu for accessing the screens for the following func- tions.
  Changing the PIN
  Adjusting the display brightness and se- lecting the color setting
  Selecting the display units
To change the PIN:
(1) Input the current PIN, and then tap the
“Enter” button.
(2) Input the new PIN, and then tap the
“Save” button.
(3) Input the new PIN again, and then tap the
“Confirm Save” button.
Adjusting the display brightness and se- lecting the color setting (“Display”)
The brightness of the display can be set with- in a range from 1% to 100%.
 49
]]></page><page Index="56" isMAC="true"><![CDATA[   Instrument operation
The color of the segments shown in the bar graphs and the color that indicates selected items can be changed.
1
100% Background Color
2
1 Brightness adjustment slider 2 Color selection slider
To adjust the display brightness:
To make the display brighter, drag the slider to the right. To make the display darker, drag the slider to the left.
To select the color setting:
Drag the color selection slider to the left or right to change the color setting to blue, red, green, pink, orange, purple, yellow, or light blue.
Selecting the display units (“Unit”)
The following display units can be selected for the display units of the multifunction infor- mation center.
  “US Unit”: Distances are shown in miles,
speeds are shown in MPH, and fuel amounts are shown in gallons.
  “Metric”: Distances are shown in kilome- ters, speeds are shown in km/h, and fuel amounts are shown in liters.
   Unit
Metric US Unit Metric Save
      To select the display units:
Flick up or down to select “US Unit” or “Met- ric” under “Unit”, and then tap the “Save” button.
Selecting the display language (“Lan- guage”)
The display language for the multifunction in- formation center can be selected from the following languages.
  English
  French
  Spanish
    Language
Españor English Français Save
To select the display language:
Flick up or down to select the desired lan- guage under “Language”, and then tap the “Save” button.
 50
]]></page><page Index="57" isMAC="true"><![CDATA[  Displayingthetimesincethelastmainte- nance (“Wellness”)
The total number of hours that the engine has been running since the last watercraft main- tenance can be displayed.
Time Since Last Maintenance
30.0Hrs
Reset
To reset the number of hours of operation:
(1) Tap the “Reset” button.
(2) Tap the “Confirm Reset” button to reset
the number of hours of operation.
Resetting the settings, trip information, and fuel information (“Reset”)
The settings, trip information, and fuel infor- mation can be reset to their factory default settings. The items that are reset and the de- fault settings are as follows.
  Display units: US Unit
  Language: English
  Display brightness: 100%
  Color setting: Blue
  Trip time: 0.0
  Distance traveled: 0.0
  Average fuel consumption per gallon or li-
ter: 0.0
Instrument operation
 Totalfuelused:0.0
 Reset To Factory?
Reset
  To reset the settings, trip information, and fuel information:
(1) Tap the “Reset” button.
(2) Tap the “YES” button in the confirmation
screen.
EJU45190
Engine lock screen “ ”
The engine lock screen shows the setting screen for the Yamaha Security System in the center display. (See page 30 for Yamaha Se-
curity System setting procedures.)
EJU45202
Warning function
The multifunction information center can indi-
cate the following warnings.
  Fuel level warning
  Battery voltage warning
  Check engine warning
  Engine overheat warning
  Oil pressure warning
  Other warnings (communication errors, ex-
ceeding the maintenance intervals, and so
on)
To stop the buzzer when a malfunction is ac- tivated, correct the cause of the problem and
   51
]]></page><page Index="58" isMAC="true"><![CDATA[ Instrument operation
start the engine again, or push the “ALARM MUTE” button.
running, the voltage display of the voltmeter blinks.
        0 10.8V
MPH
x100 RPM
100% F
             1 “ALARM MUTE” button
TIP:
If the battery voltage warning is activated, have the watercraft serviced by a Yamaha dealer as soon as possible.
Check engine warning “ ”
If a sensor malfunction or a short circuit is de- tected, the warning bar is shown instead of the tachometer value display, “ ” is shown, and the buzzer sounds intermittently.
If the check engine warning is activated, im- mediately reduce the engine speed, return to shore, and have a Yamaha dealer check the engine.
TIP:
Tap “ ” to display a description of the warning in the center display.
Engine overheat warning “ ”
If the engine temperature rises significantly, the warning bar is shown instead of the ta- chometer value display, “ ” and “ ” are shown, and the buzzer sounds continuously.
If the “ALARM MUTE” button was pushed to stop the buzzer, the buzzer will start sound- ing again after 5 minutes.
Fuel level warning
If the amount of remaining fuel is less than 10%, the percentage display of the fuel level meter changes to “Low”, and the buzzer sounds intermittently.
1
            0
13.6V x100 RPM
F
MPH
Low
   If the fuel level warning is activated, refill the fuel tank as soon as possible. (See page 62 for information on filling the fuel tank.) Battery voltage warning
If the battery voltage is less than 12 volts or more than 18 volts when the engine is not
     52
]]></page><page Index="59" isMAC="true"><![CDATA[ If the engine overheat warning is activated, immediately reduce the engine speed, return to shore, and then make sure that water is being discharged from the port (left) cooling water pilot outlet while the engine is running. If there is no discharge of water, stop the en- gine, and then check the jet intake for clog- ging. (See page 105 for information on the jet intake.) NOTICE: If you cannot locate and correct the cause of the overheating, con- sult a Yamaha dealer. Continuing to oper- ate at higher speeds could result in severe engine damage. [ECJ00042]
Instrument operation
(See page 64 for information on checking the engine oil level.) If the oil level is sufficient, have a Yamaha dealer check the watercraft.
TIP:
  While the oil pressure warning is activated, the maximum engine speed is limited.
  Tap “ ” to display a description of the warning in the center display.
Other warnings (communication errors, exceeding the maintenance intervals, and so on) “ ”
If any other malfunction is detected or if the engine has been operated for more than 50 hours since the last maintenance, the warn- ing bar is shown instead of the tachometer value display, “ ” is shown, and the buzz- er sounds intermittently.
If a warning is activated, have the watercraft serviced by a Yamaha dealer as soon as pos- sible.
TIP:
           TIP:
  While the engine overheat warning is acti- vated, the maximum engine speed is limit- ed.
  Tap “ ” to display a description of the warning in the center display.
Oil pressure warning “ ”
If the oil pressure drops significantly, the warning bar is shown instead of the tachom-
eter value display, “ ” and “ ” are shown, and the buzzer sounds intermittently.
If the oil pressure warning is activated, imme- diately reduce the engine speed, return to shore, and then check the engine oil level.
” to display a description of the
Tap “
warning in the center display.
    53
]]></page><page Index="60" isMAC="true"><![CDATA[Equipment operation
 EJU40335
EJU45210
Seats
Equipment
To install the rear seat:
(1) Insert the projections on the front of the
seat into the stays on the deck.
 The front and rear seats are removable. Remove the seats to access the engine com- partment and removable watertight storage compartment.
To remove the rear seat:
(1) Pull the rear seat latch up, and then lift up
the rear of the seat.
     1
          1 Seat latch
(2) Pull the seat rearward and remove it.
(2) Push the rear of the seat down to secure- ly lock it in place.
       To remove the front seat:
(1) Remove the rear seat.
(2) Pull the front seat latch up, and then lift
up the rear of the seat.
  1
         54
1 Seat latch
]]></page><page Index="61" isMAC="true"><![CDATA[ (3) Pull the seat rearward and remove it.
Equipment operation
EJU31364
Handgrip
The handgrip is used when boarding the wa- tercraft from the water and when the spotter is facing rearward. WARNING! Do not use the handgrip to lift the watercraft. The handgrip is not designed to support the watercraft’s weight. If the handgrip breaks, the watercraft could fall, which could result in severe injury. [EWJ00022]
               1
     To install the front seat:
(1) Insert the projection on the front of the
seat into the space under the glove com- partment as shown.
                       (3) Securely install the rear seat in its original position.
1 Reboarding grip
EJU34865
Reboarding step
The reboarding step is used to assist in re- boarding the watercraft from the water. When boarding the watercraft, push the re- boarding step down until it stops. The step returns automatically to its original position
1 Handgrip
EJU37382
Reboarding grip
The reboarding grip is used when boarding the watercraft from the water.
  1
     (2) Push the rear of the seat down to secure- ly lock it in place.
55
]]></page><page Index="62" isMAC="true"><![CDATA[Equipment operation
when released. WARNING! Do not use the reboarding step to lift the watercraft. The reboarding step is not designed to support the watercraft’s weight. If the reboarding step breaks, the watercraft could fall, which could result in severe injury. [EWJ01212]
EJU34873
Bow eye
The bow eye is used to attach a rope to the watercraft when transporting, mooring, or towing it in an emergency. (See page 109 for information on towing the watercraft.)
          1
      1
1 Reboarding step
1 Bow eye
EJU34882
Stern eyes
The stern eyes are used to attach a rope to the watercraft when transporting or mooring it.
           1
1
     ECJ00743
Use the reboarding step only to board the watercraft in the water. Do not use the re- boarding step for any other purpose. The watercraft can be damaged.
Cleat
The cleat is used to attach a ski rope to the watercraft when pulling a wakeboarder or water-skier. WARNING! Do not use the cleat to lift the watercraft. The cleat is not designed to support the watercraft’s weight. If the cleat breaks, the watercraft
  1 Stern eye
EJU40423
 56
]]></page><page Index="63" isMAC="true"><![CDATA[ could fall, which could result in severe in- jury. [EWJ01511]
Equipment operation
cleats break, the watercraft could fall, which could result in severe injury. [EWJ00822] FX CRUISER SVHO
  1
        1
      1 Cleat EJU34894
Pull-up cleats (FX CRUISER SVHO / FX LIMITED SVHO)
The pull-up cleats are used to attach a rope to the watercraft when mooring it.
To use a pull-up cleat, pull it up. The pull-up cleat returns automatically to its original posi- tion when released. WARNING! Do not use the pull-up cleats to lift the watercraft. The pull-up cleats are not designed to support the watercraft’s weight. If the pull-up
1 Pull-up cleat
FX LIMITED SVHO
  1
      1 Pull-up cleat
EJU35148
Storage compartments
This watercraft is equipped with the following storage compartments.
Only the securely closed watertight storage compartment is waterproof. If you carry ob- jects that must be kept dry, put them in a wa- terproof bag.
Make sure that the storage compartments
are closed securely before operating the wa-
tercraft.
EJU45250
Bow storage compartment
The bow storage compartment is located un- der the hood.
57
]]></page><page Index="64" isMAC="true"><![CDATA[  Equipment operation
To open the bow storage compartment:
Pull the hood latch rearward, and then lift up the rear of the hood.
To close the bow storage compartment: Push the rear of the hood down to securely lock it in place.
     1
                   1 Hood latch
EJU45080
Glove compartment
The glove compartment is located in front of the seat.
To open the glove compartment:
Unhook the glove compartment latch, and then lift up the lid.
   1
                  1
  1 Bow storage compartment
   Bow storage compartment: Capacity:
130.0 L (34.3 US gal, 28.6 Imp.gal) Load limit:
5.0 kg (11 lb)
 1 Glove compartment latch
          1
 58
1 Glove compartment
]]></page><page Index="65" isMAC="true"><![CDATA[Equipment operation
To open the stern storage compartment: Unhook the stern storage compartment latch on both sides, and then open the lid.
    Glove compartment: Capacity:
17.0 L (4.5 US gal, 3.7 Imp.gal) Load limit:
1.0 kg (2 lb)
     1
  To close the glove compartment:
Lower the lid, and then hook the glove com- partment latch.
           1 Stern storage compartment latch
  2
1
         To drain water from the glove compartment: (1) Remove the drain plugs on the bottom of the glove compartment to drain the wa-
ter.
    1
     Stern storage compartment: Capacity:
11.0 L (2.9 US gal, 2.4 Imp.gal) Load limit:
1.5 kg (3 lb)
  1 Drain plug
(2) Securely install the drain plugs in their
1 Stern storage compartment lid 2 Stern storage compartment
To close the stern storage compartment: Close the lid, and then hook the stern storage compartment latch on both sides.
TIP:
The ski rope slot in the stern storage com- partment lid can be used to store the rope in
original positions. EJU45220
Stern storage compartment
The stern storage compartment is located in front of the boarding platform.
59
]]></page><page Index="66" isMAC="true"><![CDATA[Equipment operation
the stern storage compartment while the rope is attached to the cleat.
To open the removable watertight storage compartment:
(1) Remove the rear seat. (See page 54 for
seat removal and installation proce-
dures.)
(2) Loosen the cap and remove it.
     1
               1
1 Ski rope slot EJU35175
Beverage holder
The beverage holder is located near the star- board (right) side of the multifunction infor- mation center.
1 Cap
          1
  1
             1 Beverage holder
Do not place any items in the beverage hold-
er while riding. Otherwise, the items may fall
out of the beverage holder.
EJU37235
Removable watertight storage compart-
ment
The removable watertight storage compart- ment is located under the rear seat.
The compartment is watertight when the cap is closed securely.
1 Removable watertight storage compart- ment
To close the removable watertight storage compartment:
(1) Securely install the cap by tightening it
until it stops.
(2) Securely install the rear seat in its original
position.
   Removable watertight storage compart- ment:
Capacity:
9.0 L (2.4 US gal, 2.0 Imp.gal)
Load limit: 3.0 kg (7 lb)
   60
]]></page><page Index="67" isMAC="true"><![CDATA[   EJU42391
Fire extinguisher holder and cover
The fire extinguisher holder and cover are lo- cated in the bow storage compartment.
To use the fire extinguisher holder and cover: (1) Pull the hood latch rearward, and then lift
up the rear of the hood.
Equipment operation
hood is securely closed before using the watercraft.
       1
               1 Hood latch
(2) Unhook the band and remove the fire ex-
tinguisher cover.
EJU45291
Optional part mounting bracket
A mounting bracket for installing optional parts is located near the port (left) side of the multifunction information center.
 1
                   1
2
        1 Fire extinguisher holder and cover 2 Band
(3) Place the fire extinguisher in the holder, and then place the cover over the fire ex- tinguisher.
(4) Securely fasten the cover and the fire ex- tinguisher with the band.
(5) Push the rear of the hood down to se- curely lock it in place. Make sure that the
1 Optional part mounting bracket
Load limit:
1.0 kg (2.2 lb)
 61
]]></page><page Index="68" isMAC="true"><![CDATA[Operation and handling requirements
 EJU31823
Fuel requirements Fuel
knocking (or pinging) occurs, use a gasoline of a different brand.
Gasohol
There are two types of gasohol: gasohol con- taining ethanol and that containing methanol. Gasohol containing ethanol can be used if ethanol content does not exceed 10% and the fuel meets the minimum octane ratings. E-85 is a fuel blend containing 85% ethanol and therefore must not be used in this water- craft. All ethanol blends containing more than 10% ethanol can cause fuel system damage or engine performance problems.
Yamaha does not recommend gasohol con- taining methanol because it can cause fuel system damage and engine performance problems.
To fill the fuel tank:
(1) Before refueling, stop the engine. Do not
stand or sit on the watercraft. Never refu- el while smoking, or while in the vicinity of sparks, open flames, or other sources of ignition.
(2) Place the watercraft in a well-ventilated area and in a horizontal position.
(3) Remove the seats, and then check the fuel level. (See page 54 for seat removal and installation procedures.)
EJU45230 EWJ00283
   Recommended fuel:
Premium unleaded gasoline with a minimum octane rating of
91
(Pump octane number) = (R + M)/2
95 (Research octane number)
     Gasoline and gasoline vapors are ex- tremely flammable. To avoid fires and explosions and to reduce the risk of in- jury when refueling, follow these in- structions.
  Gasoline is poisonous and can cause in- jury or death. Handle gasoline with care. Never siphon gasoline by mouth. If you should swallow some gasoline, inhale a lot of gasoline vapor, or get some gaso- line in your eyes, see your doctor imme- diately. If gasoline spills on your skin, wash with soap and water. If gasoline spills on your clothing, change your clothes.
ECJ01870
  Do not use leaded gasoline. Leaded gasoline can seriously damage the en- gine.
  Avoid getting water and contaminants in the fuel tank. Contaminated fuel can cause poor performance and engine damage. Use only fresh gasoline that has been stored in clean containers.
  Use only gasoline with a minimum pump octane number of 91 or a minimum re- search octane number of 95. Low-oc- tane gasoline can seriously damage the engine.
Your Yamaha engine has been designed to use premium unleaded gasoline with a pump octane number [(R+M)/2] of 91 or higher, or a research octane number of 95 or higher. If
     62
]]></page><page Index="69" isMAC="true"><![CDATA[ (5)
Slowly add fuel to the fuel tank.
Fuel tank capacity:
70 L (18.5 US gal, 15.4 Imp.gal)
1 Top of the fuel tank
2 Approximately 50 mm (2 in) from top of the
fuel tank
1 Fuel filler cap
Operation and handling requirements
 (4) Loosen the fuel filler cap and remove it.
Do not leave the watercraft with a full tank in direct sunlight.
  1
                     1
2
    1
2
             (6)
Stop filling when the fuel level reaches approximately 50 mm (2 in) from the top of the fuel tank. Do not overfill the fuel tank. Because fuel expands when it heats up, heat from the engine or the sun can cause fuel to spill out of the fuel tank.
1 Top of the fuel tank
2 Approximately 50 mm (2 in) from top of the
fuel tank
(7) Wipe up any spilled fuel immediately with a dry cloth.
(8) Securely install the fuel filler cap by tight- ening it until it clicks.
(9) Securely install the seats in their original positions.
63
]]></page><page Index="70" isMAC="true"><![CDATA[Operation and handling requirements
 EJU40291
Engine oil requirements
EJU41514
Engine oil
ECJ00282
Use only 4-stroke engine oil. Usage of 2- stroke engine oil could result in severe en- gine damage.
Yamalube the best choice for your Yamaha engine.
Checking the engine oil level
EWJ00341
Engine oil is extremely hot immediately af- ter the engine is turned off. Coming in con- tact with or getting any engine oil on your clothes could result in burns.
ECJ01002
Make sure that debris and water do not enter the oil filler hole. Debris and water in the engine oil can cause serious engine damage.
To check the engine oil level:
(1) Place the watercraft in a precisely level
position on land with the engine stopped. If the engine was running, allow the engine oil to settle by waiting 5 min- utes or more before checking the oil lev- el.
(2) Remove the seats. (See page 54 for seat removal and installation procedures.)
                 Recommended engine oil:
YAMALUBE 4W or 4-stroke motor oil
Recommended engine oil type: SAE 10W-30, 10W-40, 20W-40, 20W-50
Recommended engine oil grade: API SG, SH, SJ, SL
    TIP:
When the engine is operated at high speeds, some engine oil may be consumed. Be sure to check the engine oil level.
Why Yamalube
YAMALUBE oil is a Genuine YAMAHA Part born of the engineers’ passion and belief that engine oil is an important liquid engine com- ponent. We form teams of specialists in the fields of mechanical engineering, chemistry, electronics and track testing, and have them develop the engine together with the oil it will use. Yamalube oils take full advantage of the base oil’s qualities and blend in the ideal bal- ance of additives to make sure the final oil clears our performance standards. Thus, Yamalube mineral, semisynthetic and syn- thetic oils have their own distinct characters and value. Yamaha’s experience gained over many years of research and development into oil since the 1960’s helps make
    64
]]></page><page Index="71" isMAC="true"><![CDATA[1 Dipstick
Operation and handling requirements
 (3) Remove the dipstick and wipe it clean.
(6) Loosen the engine oil filler cap and re- move it.
 1
   1
(4) Insert the dipstick back into the dipstick tube completely. Remove the dipstick again and make sure that the engine oil level is between the minimum and maxi- mum level marks.
1 Engine oil filler cap
(7) Slowly add engine oil.
TIP:
The difference between the minimum and maximum level marks on the dipstick is equal to approximately 1 L (1.06 US qt, 0.88 Imp.qt) of engine oil.
(8) Wait approximately 5 minutes to allow the engine oil to settle, and then check the engine oil level again.
(9) Repeat steps 3–8 until the engine oil is at the proper level.
(10) Securely install the engine oil filler cap by tightening it until it stops.
(11) Securely install the seats in their original positions.
 1 2
1 Maximum level mark
2 Minimum level mark
(5) If the engine oil level is significantly above the maximum level mark, consult a Yamaha dealer. If the engine oil level is below the minimum level mark, add en- gine oil.
65
]]></page><page Index="72" isMAC="true"><![CDATA[Operation and handling requirements
 EJU40022
Draining the bilge water
ECJ01302
Do not run the engine at full throttle when bilge water remains in the engine com- partment. The bilge water can splash into the engine, which can result in severe damage.
EJU44260
Draining the bilge water on land
To drain the bilge water on land:
(1) Loosen the stern drain plugs and remove
them.
drain plugs could be damaged, allow- ing water to enter the engine compart- ment. Check the O-rings on the stern drain plugs and make sure that the plugs are tightened securely before launching the watercraft. Otherwise, water may flood the engine compart- ment and cause the watercraft to sub- merge. [ECJ00363]
      1
     1
1 Stern drain plug
(2) Raise the bow of the watercraft, such as by placing the watercraft on a slope, to drain the bilge water from the engine compartment.
(3) After the bilge water has drained from the stern drain plug holes, wipe up any re- maining moisture in the engine compart- ment with a dry cloth.
(4) Check that the stern drain plugs and O- rings on the plugs are not damaged and that there is no foreign material on the threads or O-rings on the plugs. NOTICE: Before installing the stern drain plugs, clean the drain plug threads and the O-rings on the plugs to remove any foreign materials, such as dirt or sand. Otherwise, the stern
1 O-ring
(5) Securely install the stern drain plugs by
tightening them until they stop. EJU40535
Draining the bilge water on water
A small quantity of bilge water will remain in the engine compartment even after the bilge water is drained on water. To completely drain the bilge water, remove the watercraft from the water and drain the bilge water on land.
Jet vacuum bilge draining system
While the watercraft is operating, bilge water in the engine compartment is drawn in by the vacuum that is generated in the jet pump and discharged from the watercraft through the jet thrust nozzle.
To drain the bilge water on water:
Operate the watercraft as straight as possible and above planing speed for at least 2 min- utes. NOTICE: Do not run the engine at full throttle for at least 1 minute after the en- gine has been restarted. Bilge water in the
 66
]]></page><page Index="73" isMAC="true"><![CDATA[Operation and handling requirements
 engine compartment can splash into the engine, which can result in severe dam- age. [ECJ00554]
EJU42432
Transporting on a trailer
When transporting the watercraft on a trailer, secure the tie downs to the trailer through the bow eye and stern eyes. NOTICE: Do not at- tach ropes or tie downs to any part of the watercraft other than the bow eye and stern eyes to secure the watercraft to the trailer. Otherwise, the watercraft may be damaged. Wrap the ropes or tie downs with towels or rags where they touch the body of the watercraft to avoid scratches or damage. [ECJ02150]
                    67
]]></page><page Index="74" isMAC="true"><![CDATA[First-time operation
 EJU42690
ECJ00432
Engine break-in
  Failure to perform the engine break-in could result in reduced engine life or even severe engine damage.
The engine break-in is essential to allow the various components of the engine to wear and polish themselves to the correct operat- ing clearances. This ensures proper perfor- mance and promotes longer component life. To perform the engine break-in:
(1) Check the engine oil level. (See page 64 for information on checking the engine oil level.)
(2) Launch the watercraft and start the en- gine. (See page 80 for information on starting the engine.)
(3) For the first 5 minutes, operate with the engine speed at 2000 r/min.
(4) For the next 90 minutes, operate with the engine speed below 5000 r/min.
After the engine break-in is complete, the wa- tercraft can be operated normally.
  68
]]></page><page Index="75" isMAC="true"><![CDATA[EJU31982
EWJ00412
Failure to inspect or maintain the watercraft properly increases the possibility of an ac- cident or damage to the watercraft. Do not operate the watercraft if you find any prob- lem. If a problem cannot be corrected by the procedures provided in this manual, have the watercraft inspected by a Yamaha dealer.
EJU41235
Pre-operation checklist
Before using this watercraft, be sure to perform the checks in the following checklist.
Pre-operation checks
     ITEM ROUTINE PAGE
 PRE-LAUNCH CHECKS
 Engine compartment
Ventilate the engine compartment.
Check inside the engine compartment for damage.
71
Fuel system
Check the fuel system for leakage. Check the fuel level in the fuel tank.
71
Water separator
Check the water separator for water.
72
Engine unit
Check the exterior of the engine unit for damage.
72
Engine oil level
Check the engine oil level.
72
Bilge water
Check the engine compartment for bilge water.
72
Battery
Check the battery connections.
72
Steering system
Check the steering system for proper operation.
73
Adjustable tilt steering sys- tem
Check the adjustable tilt steering system for proper operation and check that the handlebars are se- curely locked in place.
74
RiDE lever
Check the RiDE lever for proper operation.
74
Throttle lever
Check the throttle lever for proper operation.
74
Yamaha Security System
Check the Yamaha Security System for proper op- eration.
74
Engine shut-off cord (lan- yard)
Check the engine shut-off cord (lanyard) for dam- age.
74
Switches
Check the start switch, engine stop switch, and en- gine shut-off switch for proper operation.
74
Electric trim system
Check the electric trim system for proper operation.
75
Storage compartments
Check the storage compartments for damage and water.
75
Fire extinguisher holder, cover, and band
Check the fire extinguisher holder, cover, and band for damage.
75
Fire extinguisher
Check the condition of the fire extinguisher.
76
Safety equipment
Check that safety equipment meeting the applica- ble regulations is on board.
76
Hull and deck
Check the hull and deck for damage.
76
Jet intake
Check the jet intake for damage and clogging.
76
                         69
]]></page><page Index="76" isMAC="true"><![CDATA[Pre-operation checks
    ITEM
ROUTINE
PAGE
Jet thrust nozzle and re- verse gate
Check the jet thrust nozzle and reverse gate for damage.
76
Stern drain plugs
Check the stern drain plugs for damage and foreign material and check that they are securely installed.
76
Hood
Check that the hood is securely closed.
77
Front and rear seats
Check that the seats are securely installed.
54
 POST-LAUNCH CHECKS
 Cooling water pilot outlet
Check that water is discharged from the port (left) cooling water pilot outlet while the engine is run- ning.
77
Multifunction information center
Check the multifunction information center for prop- er operation.
77
Shift system
Check the shift system for proper operation.
77
Engine idling speed
Check the engine idling speed.
78
            TIP:
To ensure safety and reliability, pre-operation checks should be made each time the water- craft is used.
70
]]></page><page Index="77" isMAC="true"><![CDATA[ EJU32282
Pre-operation check points
EJU42384
Pre-launch checks
Perform the pre-launch checks in the pre-op- eration checklist while the watercraft is on land.
To perform the pre-launch checks:
(1) Remove the seats and removable water- tight storage compartment. (See page 54 for seat removal and installation proce- dures and page 60 for information on the removable watertight storage compart- ment.)
(2) Perform the checks and make sure that there are no malfunctioning items or oth- er problems.
(3) After completing these checks, securely install the removable watertight storage compartment and seats in their original
positions.
EJU32334
Engine compartment check
EWJ00462
Failure to ventilate the engine compart- ment could result in a fire or explosion. Do not start the engine if there is a fuel leak.
Ventilatetheenginecompartment.Leavethe engine compartment open for a few minutes to allow any fuel vapors to escape.
Pre-operation checks
Make sure that there is no damage inside the engine compartment.
     EJU34215
Fuel system checks
EWJ00382
Leaking fuel can result in fire or explosion.
  Check for fuel leakage regularly.
  If any fuel leakage is found, the fuel sys-
tem must be repaired by a qualified me- chanic. Improper repairs can make the watercraft unsafe to operate.
Make sure that there is no damage, leakage, or other problem in the fuel system.
Check:
  Fuel filler cap and seal for damage
  Fuel tank for damage and leakage  Fuelhosesandjointsfordamageandleak-
age
  Fuel tank breather hose for damage and
leakage EJU36875
Fuel level check
Check the fuel level in the fuel tank.
Add fuel if necessary. (See page 62 for infor- mation on filling the fuel tank.)
      71
]]></page><page Index="78" isMAC="true"><![CDATA[ Pre-operation checks
EJU32424
Water separator check
Make sure that no water has collected in the water separator. If water has collected in the water separator, drain it. (See page 34 for in- formation on draining the water separator.)
EJU36886
Engine oil level check
Make sure that the engine oil level is between the minimum and maximum level marks on the dipstick. (See page 64 for information on checking the engine oil level.)
         1
            1
1 Water separator EJU40182
Engine unit check
Check the exterior of the engine unit for dam- age or other problem.
1 Dipstick
 1 2
72
1 Maximum level mark
2 Minimum level mark EJU32456
Bilge water check
Make sure that no bilge water has collected in the engine compartment. If bilge water has collected in the engine compartment, drain it. (See page 66 for information on draining the
bilge water.) EJU32486
Battery checks
Make sure that the battery terminals are not damaged and that the battery leads are con- nected properly. WARNING! Never operate the watercraft if the battery does not have sufficient power to start the engine or if it
]]></page><page Index="79" isMAC="true"><![CDATA[ shows any other signs of decreased pow- er. Loss of battery power may leave you stranded. [EWJ01241]
Pre-operation checks
right and left fully turned positions of the jet thrust nozzle.
     12
                    1 Negative (–) battery terminal: Black lead 2 Positive (+) battery terminal: Red lead
Make sure that the battery is securely held in
place.
EJU32614
Steering system checks
Turn the handlebars to the right and left sev- eral times to make sure that operation is smooth and unrestricted throughout the whole range, and that the free play is not ex- cessive.
              Turn the handlebars as far as possible to the right and left to make sure that the jet thrust nozzle moves as the handlebars are turned, and that there is no difference between the
Difference between fully turned posi- tions of jet thrust nozzle (distances A and B):
Maximum 5 mm (0.20 in)
   73
]]></page><page Index="80" isMAC="true"><![CDATA[Pre-operation checks
EJU40363
Adjustable tilt steering system checks
Operate the adjustable tilt steering system several times to make sure that operation is smooth throughout the whole range. Also, make sure that the handlebars are securely locked in place. (See page 33 for adjustable tilt steering system operation procedures.)
throttle lever returns automatically to its fully closed (idle) position when released.
            EJU43213
RiDE lever checks
Operate the RiDE lever several times to make sure that operation is smooth throughout the whole range. Also, make sure that the RiDE lever returns automatically to its fully closed position when released.
EJU45350
Yamaha Security System check
Make sure that the Yamaha Security System
operates properly. (See page 30 for Yamaha
Security System setting procedures.) EJU32664
Engine shut-off cord (lanyard) check
Make sure that the engine shut-off cord (lan- yard) is not damaged. If the cord is damaged, replace it. WARNING! Never try to repair the engine shut-off cord (lanyard) or tie it together. The engine shut-off cord (lan- yard) may not pull free when the operator falls off, allowing the watercraft to contin- ue to run and cause an accident. [EWJ01221]
EJU32676
Switch checks
ECJ01311
Do not run the engine over 4000 r/min on land. Also, do not run the engine for more
    EJU42181
Throttle lever checks
Operate the throttle lever several times to make sure that operation is smooth through- out the whole range. Also, make sure that the
  74
]]></page><page Index="81" isMAC="true"><![CDATA[ than 15 seconds without supplying water, otherwise the engine could overheat.
Check the start switch, the engine stop switch, and the engine shut-off switch for proper operation. (See pages 31 to 31 for in- formation on operating each switch.)
Pre-operation checks
and down properly and that the trim setting indicator and displayed setting level change according to the operation of the switches. (See page 45 for information on turning on the multifunction information center without starting the engine and page 37 for informa- tion on the electric trim system.)
  123
4
    5
     0
1 Clip
2 Engine shut-off switch
3 Start switch
4 Engine stop switch
5 Engine shut-off cord (lanyard)
To check the operation of the switches:
(1) If the lock mode is selected for the Yamaha Security System setting, select the unlock mode. (See page 30 for Yamaha Security System setting proce-
dures.)
(2) Push the start switch to make sure that
the engine starts.
(3) As soon as the engine starts running,
push the engine stop switch to make
sure that the engine stops immediately.
(4) Restart the engine, and then pull the en- gine shut-off cord (lanyard) to remove the clip from the engine shut-off switch to make sure that the engine stops im-
mediately.
EJU45370
Electric trim system check
Turn on the multifunction information center, and then operate the “TRIM/T.D.E.” switch- es. Check that the jet thrust nozzle moves up
EJU40102
Storage compartment checks
Make sure that the storage compartments are not damaged and that water has not col- lected in the compartments. (See page 57 for
information on the storage compartments.) EJU41082
Fire extinguisher holder, cover, and band
checks
Make sure that the fire extinguisher holder, cover, and band are not damaged and that the cover is securely held in place using the band. (See page 61 for information on the fire extinguisher holder, cover, and band.)
 75
]]></page><page Index="82" isMAC="true"><![CDATA[Pre-operation checks
EJU32535
Fire extinguisher check
Check that there is a full fire extinguisher on board.
To check the fire extinguisher, see the in- structions supplied by the fire extinguisher manufacturer. Always keep the fire extin- guisher secured in the holder with its cover in place.
Always carry a fire extinguisher on board. A fire extinguisher is not standard equipment with this watercraft. If you do not have one, contact a Yamaha dealer or a fire extinguish- er dealer to obtain one meeting the proper specifications.
EJU40122
Safety equipment check
Check that safety equipment meeting the ap-
plicable regulations is on board. EJU32353
Hull and deck check
Check the hull and deck for damage or other problem.
EJU32657
Jet intake checks
Make sure that the jet intake is not damaged or clogged with weeds or debris. If the jet in- take is clogged, clean it. (See page 105 for in-
formation on the jet intake.)
EJU43221
Jet thrust nozzle and reverse gate check
Check the jet thrust nozzle and reverse gate
for damage or other problem. EJU44250
Stern drain plug checks
Loosen the stern drain plugs and remove them, and then make sure that the plugs and O-rings on the plugs are not damaged and that there is no foreign material on the threads or O-rings on the plugs. NOTICE: Before installing the stern drain plugs, clean the drain plug threads and the O- rings on the plugs to remove any foreign materials, such as dirt or sand. Otherwise, the stern drain plugs could be damaged, allowing water to enter the engine com- partment. Check the O-rings on the stern drain plugs and make sure that the plugs are tightened securely before launching the watercraft. Otherwise, water may flood the engine compartment and cause the watercraft to submerge. [ECJ00363]
     Fire extinguisher: Classification:
5-B (B-1) Capacity:
2 lb or more
    2 1
76
1 Stern drain plug 2 O-ring
]]></page><page Index="83" isMAC="true"><![CDATA[ Securely install the stern drain plugs by tight- ening them until they stop.
Pre-operation checks
EJU41811
Cooling water pilot outlet check
Make sure that water is discharged from the port (left) cooling water pilot outlet while the engine is running. (See page 34 for informa- tion on the cooling water pilot outlets.)
   1
         1 Stern drain plug EJU41441
Hood check
Push down on the rear of the hood and make sure that it is securely closed.
EJU45260
Multifunction information center check
Make sure that the multifunction information center operates properly. (See page 45 for in- formation on proper operation of the multi-
function information center.) EJU43392
Shift system check
Operate the throttle lever and RiDE lever, and check that the watercraft moves or does not move according to the displayed shift indica- tor. (See page 35 for shift system operation procedures.) WARNING! To avoid colli- sions, operate at safe speeds and keep a
           EJU40146
Post-launch checks
Perform the post-launch checks in the pre- operation checklist while the watercraft is in the water and the engine is running.
To perform the post-launch checks:
(1) Launch the watercraft. (See page 80 for information on launching the watercraft.)
(2) Perform the checks and make sure that there are no malfunctioning items or oth-
er problems.
 77
]]></page><page Index="84" isMAC="true"><![CDATA[Pre-operation checks safe distance away from people, objects,
and other watercraft. [EWJ01860]
       MPH
0 2 F 100%
   13.6V
3
N
x100 N RPM
4
R
1
 1 Shift indicator
2 “F” (Forward position) 3 “N” (Neutral position) 4 “R” (Reverse position)
EJU40172
Engine idling speed check
Start the engine and warm it up. Use the ta- chometer in the multifunction information center to make sure that the engine idling speed is not significantly above or below the specified range.
Engine idling speed: 1250 ±100 r/min
  78
]]></page><page Index="85" isMAC="true"><![CDATA[ EJU32903
Operating your watercraft
EWJ00511
Before operating your watercraft, become familiar with all of the controls. Consult a Yamaha dealer about any control or func- tion that you do not fully understand. Fail- ure to understand how the controls work could cause an accident or prevent you from avoiding an accident.
EJU32959
Getting to know your watercraft
Operating your watercraft requires skills ac- quired through practice over a period of time. Take the time to learn the basic techniques well before attempting more difficult maneu- vers.
Operating your new watercraft can be a very enjoyable activity, providing you with hours of pleasure. However, it is essential to familiar- ize yourself with the operation of the water- craft to achieve the skill level necessary to enjoy riding safely.
Before operating this watercraft, read this owner’s/operator’s manual, the Riding Prac- tice Guide, the Riding Instruction card, and all labels on the watercraft. Pay particular atten- tion to the safety information beginning on page 10. Also, watch the WaveRunner Basic Orientation Video linked to the following QR code.
Operation
https://yamahawaverunners.com/orientation A DVD is also available at your nearest dealer for your convenience.
These materials should give you an under- standing of the watercraft and its operation. Remember: This watercraft is designed to carry the operator and up to 2 passengers. Never exceed the maximum load limit or al- low more than 3 persons (or 2 persons if a wakeboarder or water-skier is being pulled) to ride the watercraft at any time.
EJU32996
Learning to operate your watercraft
Before operating the watercraft, always per- form the pre-operation checks listed on page 69. The short time spent checking the water- craft will reward you with added safety and reliability.
Check state and local laws before operating your watercraft.
Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft. Select a wide area to learn in, where there is good visibility and light boat traffic.
Use the buddy system—operate with some- one nearby. Scan constantly for people, ob-
      Maximum load:
240 kg (530 lb)
Load is the total weight of cargo, op- erator, and passengers.
    79
]]></page><page Index="86" isMAC="true"><![CDATA[Operation
jects, and other watercraft. Be alert for conditions that limit your visibility or block your vision of others.
You should grip the handlebars firmly and keep both feet on the floor of the footwell. Do not attempt to ride with passengers until your
operating skills are fully developed. EJU40212
Riding position
Operator riding position
The operator should grip the handlebars firm- ly with both hands and sit astride the seat with both feet on the floor of the footwell.
EJU32803
Launching the watercraft
When launching the watercraft, make sure that there are no obstacles around you.
If the watercraft is launched from a trailer, someone should make sure that waves do
not push the watercraft into the trailer. EJU36346
Starting the engine on water EWJ01531
Do not apply throttle when anyone is at the rear of the watercraft. Turn the engine off or keep it at idle. Water and debris exiting the jet thrust nozzle can cause severe in- jury.
To start the engine:
(1) If the lock mode is selected for the
Yamaha Security System setting, select the unlock mode. (See page 30 for Yamaha Security System setting proce- dures.)
(2) Move the watercraft to an area that is free from weeds and debris, and has a water depth of at least 60 cm (2 ft) from the bottom of the watercraft. NOTICE: Never run the engine in water that is less than 60 cm (2 ft) deep from the bottom of the watercraft, otherwise pebbles or sand could be sucked into the jet intake, causing impeller dam- age and engine overheating. [ECJ00473]
             Passenger riding position
The passenger(s) should hold on firmly, either to the person in front of them or to the hand- grip provided, and sit astride the seat with their feet on the floor of the footwell. Never al- low a passenger to ride in front of the opera- tor. (See page 17 for information on the riding position when pulling a wakeboarder or wa- ter-skier.)
         80
]]></page><page Index="87" isMAC="true"><![CDATA[Operation
 (3) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch. (See page 31 for information on operating the en- gine shut-off switch.) WARNING! Check that the engine shut-off cord (lanyard) is attached correctly. If the engine shut-off cord (lanyard) is not attached correctly, it may not pull free when the operator falls off, allowing the water- craft to continue to run and cause an accident. [EWJ00582]
EJU32863
Stopping the engine
Release the throttle lever, and then push the engine stop switch (red button) to stop the engine. WARNING! You need throttle to steer. Shutting the engine off can cause you to hit an obstacle you are attempting to avoid. A collision could result in severe injury or death. [EWJ00602]
    12
3
       1 Clip
2 Engine shut-off switch
3 Engine shut-off cord (lanyard)
(4) With the throttle lever released, push the start switch (green button) to start the engine. (See page 31 for information on operating the start switch.)
EJU32873
Leaving the watercraft
If leaving the watercraft, remove the clip from the engine shut-off switch to prevent acci- dental starting or unauthorized operation by children or others.
   EJU43411
Operating the watercraft
When the throttle lever is squeezed, the “F” (forward) shift indicator will be displayed and the watercraft will move forward. While the “F” (forward) shift indicator is displayed, the watercraft will move forward at trolling speed even if the throttle lever is in the fully closed
 81
]]></page><page Index="88" isMAC="true"><![CDATA[Operation
(idle) position. (See page 35 for shift system operation procedures.)
Steering control depends on the combination of handlebar position and the amount of throttle.
Water sucked in through the intake grate is pressurized by the impeller in the jet pump. As the pressurized water is expelled from the pump through the jet thrust nozzle, it creates thrust to move and steer the watercraft. The higher the engine speed, the more thrust pro- duced.
The amount of jet thrust, in addition to the po- sition of the handlebars, determines how sharply you turn.
A. More throttle produces higher thrust, so
the watercraft will turn more sharply.
B. Less throttle produces lower thrust, so the watercraft will turn more gradually.
C. Releasing the throttle lever completely produces only minimum thrust. If you are traveling at speeds above trolling, you will have rapidly decreasing ability to
      0 13.6V
MPH
x100 RPM
100% F
   1
   1 “F” (Forward position)
           EJU43423
Turning the watercraft
EWJ01783
  Do not release the throttle lever when trying to steer away from objects—as with other powerboats, you need throt- tle to steer. A collision could result in se- vere injury or death.
  When operating at higher speeds, make gradual turns or slow down before turn- ing. Sharp high-speed turns may cause the watercraft to slide sideways or spin, throwing the operator and passenger(s) overboard, which could cause an injury.
  Take early action to avoid collisions. The RiDE system is not a braking device for avoiding dangerous situations.
    82
]]></page><page Index="89" isMAC="true"><![CDATA[ steer without throttle. You may still have some turning ability immediately after re- leasing the throttle lever, but once the engine slows down, the watercraft will no longer respond to handlebar input until you apply throttle again or you reach trolling speed.
At trolling speed, the watercraft can be turned gradually by handlebar position alone using just the amount of thrust available at idle.
D. If the engine is stopped while riding, there is no thrust. The watercraft will go straight even though the handlebars are turned.
You need throttle to steer.
E. If the RiDE lever is squeezed and the handlebars are turned when the water- craft is cruising at planing speed, the wa-
Operation
tercraft will turn gradually while slowing down.
1 Reverse gate
This model is equipped with the Yamaha En- gine Management System (YEMS) that in- cludes an off-throttle steering (OTS) system. It will activate at planing speeds should you attempt to steer the watercraft after releasing the throttle lever (see condition C above). The OTS system assists in turning by con- tinuing to supply some thrust while the water- craft is decelerating, but you can turn more sharply if you apply throttle while turning the handlebars. The OTS system does not func- tion below planing speeds or when the en- gine is off. Once the engine slows down, the watercraft will no longer turn in response to handlebar input until you apply throttle again
or you reach trolling speed.
EJU43253
Stopping the watercraft
The watercraft is not equipped with a sepa-
rate braking system. The watercraft slows down by water resistance or, when operating in reverse, by the water jet. The watercraft slows down as soon as the throttle lever is re- leased, but will coast for a distance before fully stopping. If you are not sure you can stop in time before hitting an obstacle, apply throttle and turn in another direction.
From full speed, the watercraft comes to a complete stop due to water resistance in ap-
     E
  1
  83
]]></page><page Index="90" isMAC="true"><![CDATA[Operation
proximately 120 m (390 ft) after the throttle le- ver is released or the engine is stopped, although this distance will vary depending on many factors, including gross weight, water surface conditions, and wind direction.
If the RiDE lever is squeezed to slow down,
the stopping distance is approximately 30%
shorter than when the RiDE lever is not used.
However, this distance will vary depending
on many factors, including gross weight, wa-
ter surface conditions, and wind direction. EWJ01793
  Allow adequate stopping distance. Stay far enough away from others so you can always safely coast to a stop.
  Take early action to avoid collisions. Re- member, watercraft and other boats do not have brakes.
  Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft to give you time to stop.
  Do not shut the engine off when slowing down in case you need engine power to steer away from a boat or other obstacle that comes into your path.
  To avoid rear-end collisions while oper- ating the watercraft, check behind you before using the RiDE lever to slow down or stop the watercraft.
EJU43445
Operating the watercraft in reverse or neutral
Operating in reverse
When the RiDE lever is squeezed, the “R” (re- verse) shift indicator will be displayed and the watercraft will move in reverse. (See page 35 for shift system operation procedures.)
       0 13.6V
MPH
x100 RPM
100% R
   1
  1 “R” (Reverse position)
            84
Make sure that there are no obstacles or peo- ple behind you before shifting into reverse.
TIP:
This model is equipped with a function which limits the engine speed in reverse. Operating in neutral
When the RiDE lever is squeezed lightly and released, the “N” (neutral) shift indicator will be displayed and the watercraft will stop in its
 ]]></page><page Index="91" isMAC="true"><![CDATA[ current location. (See page 35 for shift sys- tem operation procedures.)
Operation
bles or sand could be sucked into the jet intake, causing impeller damage and en- gine overheating. [ECJ00473]
EJU42461
Boarding alone
(1) From the rear of the watercraft, lower the reboarding step with one hand and hold it in place.
     0 13.6V
MPH
x100 RPM
100% N
   1
   60 cm (2 ft)
 1 “N” (Neutral position)
              EJU42451
Boarding the watercraft
EWJ01112
Be sure the operator and any passengers have practiced boarding from the water while still close to shore before riding. A person who has made many unsuccessful attempts to get back on the watercraft may become fatigued and suffer from ex- posure, increasing the risk of injury and drowning.
Board the watercraft in water free from weeds and debris and at least 60 cm (2 ft) deep from the bottom of the watercraft. NOTICE: Never run the engine in water that is less than 60 cm (2 ft) deep from the bottom of the watercraft, otherwise peb-
(2) Put one foot on the step, and then grasp the reboarding grip with your other hand.
              85
]]></page><page Index="92" isMAC="true"><![CDATA[Operation
(3) Pull yourself up onto the boarding plat- form and grasp the handgrip, and then move to the seat and sit astride.
holding on to the person in front of them
or to the handgrip provided.
  Before boarding the watercraft, make
sure that the engine is stopped. If the engine is running, the reverse gate may move down and a person boarding could be pinched.
The heavier the total weight of the operator and passenger(s), the more difficult it will be to balance the watercraft. Do not operate the watercraft when the total weight exceeds 240 kg (530 lb) including any cargo.
To board with passenger(s):
(1) Board as noted in the previous section
“Boarding alone”.
           (4) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch.
(5) Grip the handlebars with both hands and place both feet on the floor of the foot- well.
                    (6) Look in all directions, start the engine,
and then start off slowly. EJU43260
Boarding with passenger(s)
EWJ01800
  Severe internal injuries can occur if wa- ter is forced into body cavities as a re- sult of being near the jet thrust nozzle. Do not start the engine until the passen- gers are seated with their feet on the floor of the footwell and are securely
(2) Grip the handlebars with both hands and place both feet on the floor of the foot- well.
(3) Have the first passenger move to the rear of the watercraft.
            86
]]></page><page Index="93" isMAC="true"><![CDATA[ (4) Have the first passenger board using the same procedure as the operator, place their feet on the floor of the footwell, and securely hold on to the operator.
Operation
are securely holding on to the person in front of them or to the handgrip provided.
                   (5) Have the second passenger follow the same procedure. When the second pas- senger is boarding, try to balance the watercraft together with the first passen- ger.
(7) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch.
(8) Look in all directions, start the engine,
and then start off slowly. EJU33084
Starting off
EWJ00713
To avoid collisions:
  Scan constantly for people, objects, and
other watercraft. Be alert for conditions that limit your visibility or block your vi- sion of others.
  Operate defensively at safe speeds and keep a safe distance away from people, objects, and other watercraft.
  Do not follow directly behind watercraft or other boats. Do not go near others to spray or splash them with water, go too close to other boats, or go too fast for the traffic conditions. Avoid sharp turns or other maneuvers that make it hard for others to avoid you or understand where you are going. Avoid areas with sub- merged objects or shallow water.
  Take early action to avoid collisions. Re- member, watercraft and other boats do not have brakes. Do not release the throttle lever when trying to steer away
           (6) Make sure that the passenger(s) have their feet on the floor of the footwell and
87
]]></page><page Index="94" isMAC="true"><![CDATA[Operation
from objects—as with other power- boats, you need throttle to steer.
ECJ01341
Never run the engine in water that is less than 60 cm (2 ft) deep from the bottom of the watercraft, otherwise pebbles or sand could be sucked into the jet intake, caus- ing impeller damage and engine overheat- ing.
EJU45380
Starting off from a trailer
(1) Launch the watercraft.
(2) Attach the engine shut-off cord (lanyard)
to your left wrist, and then attach the clip
to the engine shut-off switch.
(3) Look in all directions, and then start the
engine.
(4) Squeeze the RiDE lever and move the
watercraft back slowly. (See page 35 for RiDE lever operation procedures.)
TIP:
When using the RiDE lever to start off from a trailer, you can use the reverse assist to tem- porarily increase the engine speed. (See page
39 for reverse assist operation procedures.) EJU33114
Boarding and starting off from a dock
(1) Board the watercraft from the side.
(2) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip to the engine shut-off switch.
(3) Push the watercraft away from the dock, grip the handlebars with both hands, and place both feet on the floor of the foot- well.
(4) Look in all directions, start the engine,
and then start off slowly. EJU44210
Capsized watercraft
EWJ00672
Improper uprighting can cause injury.
  Be sure to shut the engine off by pulling on the engine shut-off cord (lanyard) to remove the clip from the engine shut-off
switch.
  Do not put your hands in the intake
grate.
If the watercraft capsizes, turn it over imme- diately.
To upright the watercraft:
(1) Remove the clip from the engine shut-off
switch.
(2) Swim to the rear of the watercraft. Turn
the watercraft over by pulling on the ride plate with one hand while pushing down
           88
]]></page><page Index="95" isMAC="true"><![CDATA[ on the gunwale with your other hand or your foot.
(3) Start the engine and operate the water- craft at planing speed to drain the bilge water from the engine compartment. (See page 66 for information on draining the bilge water. If the engine does not start, see “Towing the watercraft” on page 109 or “Submerged watercraft” on page 109.) NOTICE: Do not run the en- gine at full throttle for at least 1 minute after the engine has been restarted. Bilge water in the engine compart- ment can splash into the engine, which can result in severe damage.
[ECJ00554] EJU43282
Beaching and docking the watercraft
To beach the watercraft:
(1) Make sure that there are no boats, swim-
mers, or obstacles near the beach.
Operation
(2) Release the throttle lever to reduce speed about 120 m (390 ft) before you reach the intended beaching area.
(3) Slowly approach the beach using the throttle lever and RiDE lever to control the watercraft speed. NOTICE: Never run the engine in water that is less than 60 cm (2 ft) deep from the bottom of the watercraft, otherwise pebbles or sand could be sucked into the jet intake, causing impeller damage and engine overheating. [ECJ00473]
(4) After reaching land, stop the engine, and then get off the watercraft and pull it up on the beach.
To dock the watercraft:
(1) Make sure that there are no boats, swim-
mers, or obstacles near the dock.
(2) Release the throttle lever to reduce speed about 120 m (390 ft) away from
the dock.
(3) Slowly approach the dock using the
throttle lever and RiDE lever to control
the watercraft speed.
(4) After coming alongside the dock, stop
the engine, and then get off the water-
craft. EJU37194
Operating in weeded areas
Always avoid using your watercraft in areas where weed growth is thick. If operating in weeded areas is unavoidable, alternately squeeze the throttle lever and relax your grip on the throttle lever to vary the engine speed. Weeds tend to become clogged more when operating at a steady speed and at trolling speed. If weeds may have clogged the intake area, clean the jet intake. (See page 105 for information on the jet intake.)
       89
]]></page><page Index="96" isMAC="true"><![CDATA[Operation
EJU40242
After removing the watercraft from the water
ECJ01311
Do not run the engine over 4000 r/min on land. Also, do not run the engine for more than 15 seconds without supplying water, otherwise the engine could overheat.
After operating and removing the watercraft from the water, promptly discharge the re- maining water from the cooling water pas- sages.
To discharge water from the cooling water passages:
(1) Make sure that the area around the wa-
tercraft is clear, and then start the en-
gine.
(2) Discharge the remaining water out of the
cooling water passages by alternately squeezing and releasing the throttle lever quickly for 10 to 15 seconds.
(3) Stop the engine.
      90
]]></page><page Index="97" isMAC="true"><![CDATA[ EJU37146
EWJ00331
Post-operation care
Care and storage
(4) Connect the garden hose adapter to a garden hose.
  12
    Always place the watercraft upright in a horizontal position when storing it, other- wise fuel could leak out into the engine or engine compartment, which could create a fire hazard.
After using the watercraft, always take it out of the water, clean it, and store it. Leaving the watercraft in the water for extended periods will accelerate the rate of normal deteriora- tion of the jet pump and hull. Marine organ- isms and corrosion are some of the conditions that can shorten the life of many
watercraft components.
EJU42771
Flushing the cooling water passages ECJ01880
  Do not run the engine over 4000 r/min on land. Also, do not run the engine for more than 15 seconds without supplying water, otherwise the engine could over- heat.
  Flush the cooling water passages to prevent them from clogging with salt, sand, or dirt.
(1) Place the watercraft in a horizontal posi- tion.
(2) Remove the seats and removable water- tight storage compartment. (See page 54 for seat removal and installation proce- dures and page 60 for information on the removable watertight storage compart- ment.)
(3) Open the stern storage compartment. (See page 59 for information on the stern storage compartment.)
1 Garden hose adapter 2 Garden hose
(5) Loosen the flushing hose connector cap and remove it. Insert the garden hose adapter into the flushing hose connector by pushing and twisting it until it is se- curely connected.
    1
2
3
               1 Flushing hose connector
2 Flushing hose connector cap 3 Garden hose adapter
(6) Connect the garden hose to a water tap. (7) Make sure that the area around the wa- tercraft is clear, and then start the en- gine. Immediately after the engine starts, fully turn the water supply on so that wa-
91
]]></page><page Index="98" isMAC="true"><![CDATA[Care and storage
ter flows out continually from the jet thrust nozzle.
(2) Rinse the engine and engine compart- ment with a small amount of water. NOTICE: Do not use high-pressure water when rinsing the engine or en- gine compartment as severe engine damage could result. [ECJ00572]
(3) Drain the water from the engine com- partment. (See page 66 for information on draining the bilge water.)
(4) Wipe the engine and engine compart- ment with a dry cloth.
(5) Wash down the hull, deck, and jet pump with fresh water.
(6) Wipe the hull, deck, and jet pump with a dry cloth.
(7) Wipe all vinyl and rubber components, such as the seats and engine compart- ment seals, with a vinyl protectant such as Yamaclean Vinyl DressingTM.
(8) To minimize corrosion, spray metallic parts of the hull, deck, and engine with a rust inhibitor such as Yamalube Silicone Protectant & Lubricant.
(9) Allow the engine compartment to air dry completely before installing the seats.
(10) Securely install the seats in their original
positions. EJU41634
Battery care
If the watercraft will not be used for more than a month, remove the battery from the water- craft, check it, and then store it in a cool, dry place.
EWJ00792
Battery electrolyte is poisonous and dan- gerous, causing severe burns, etc. Elec- trolyte contains sulfuric acid. Avoid contact with skin, eyes, or clothing. Antidotes
External: Flush with water.
        (8) Run the engine at idling speed for about 3 minutes watching the engine condition. If the engine stops while flushing, turn the water supply off immediately and perform the procedure again from step 7. NOTICE: Do not supply water to the cooling water passages when the en- gine is not running. The water could flow back through the muffler into the engine, causing severe engine dam- age. [ECJ00123]
(9) Turn the water supply off.
(10) Discharge the remaining water out of the
cooling water passages by alternately squeezing and releasing the throttle lever quickly for 10 to 15 seconds.
(11) Stop the engine.
(12) Remove the garden hose adapter, and
then securely install the flushing hose connector cap by tightening it until it stops.
(13) Securely close the stern storage com- partment.
(14) Securely install the removable watertight
storage compartment and seats in their
original positions.
EJU33747
Cleaning the watercraft
(1) Remove the seats. (See page 54 for seat removal and installation procedures.)
  92
]]></page><page Index="99" isMAC="true"><![CDATA[ Internal: Drink large quantities of water or milk. Follow with milk of magnesia, beaten egg, or vegetable oil. Call a physician im- mediately.
Eyes: Flush with water for 15 minutes and get prompt medical attention.
Batteries produce explosive gases. Keep sparks, flames, cigarettes, etc., well away. If using or charging the battery in an en- closed space, make sure that it is well ventilated. Always shield your eyes when working near batteries.
Keep out of the reach of children.
To remove the battery:
(1) Disconnect the negative (–) battery lead.
(2) Disconnect the positive (+) battery lead.
(3) Unhook the battery bands, and then re-
move the battery from the watercraft.
Care and storage
tery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the vehicle is equipped with optional electrical accesso- ries. NOTICE: To charge a VRLA (Valve Regulated Lead Acid) battery, a special (constant-voltage) battery charger is re- quired. Using a conventional battery char- ger will damage the battery. [ECJ02810]
Checking the battery bands
Make sure that the battery bands are not damaged.
1 Battery band
To store the battery:
(1) Clean the battery case using fresh water. (2) If the battery terminals are dirty or cor-
roded, clean them using a wire brush.
  1
      13
2
           1 Negative (–) battery terminal: Black lead
2 Battery band
3 Positive (+) battery terminal: Red lead
Checking the battery
  Make sure that the battery case is not dam- aged.
  Make sure that the battery terminals are not corroded or damaged.
Checking the battery voltage and charging the battery
It is recommended to have a Yamaha dealer check the battery voltage and charge the bat- tery. Have a Yamaha dealer charge the bat-
1 Battery terminal
(3) Apply water-resistant grease to the bat- tery terminals.
 1
         93
]]></page><page Index="100" isMAC="true"><![CDATA[Care and storage
  Recommended water-resistant grease: YAMALUBE MARINE GREASE
(4) Store the battery in a cool, dry place.
NOTICE: Storing the battery in an un- charged condition can cause perma- nent battery damage. Check the battery periodically. [ECJ00103]
To install the battery:
(1) Place the battery in the battery compart-
ment and hook the battery bands onto
the holders.
(2) Connect the positive (+) battery lead (red)
to the positive (+) battery terminal.
NOTICE: Reversal of the battery leads
will damage the electrical parts. [ECJ00262]
(3) Connect the negative (–) battery lead (black) to the negative (–) battery termi-
nal.
(4) Make sure that the battery is securely
EJU33493
EWJ00331
Long-term storage
     held in place.
Always place the watercraft upright in a horizontal position when storing it, other- wise fuel could leak out into the engine or engine compartment, which could create a fire hazard.
Storage for long periods of time, such as win- ter storage, requires preventive maintenance to ensure against deterioration. It is advisable to have the watercraft serviced by a Yamaha dealer prior to storage.
However, the following procedures can be
performed easily by the owner.
EJU40256
Cleaning
(1) Flush the cooling water passages. (See
page 91 for information on flushing the cooling water passages.)
TIP:
If you will be storing the watercraft for a pro- longed period, such as winter storage, top off the fuel tank with fresh gasoline and add one ounce of Yamalube Fuel Stabilizer & Condi- tioner Plus to each gallon of fuel in the fuel tank before starting the engine.
(2) Clean the watercraft. (See page 92 for in- formation on cleaning the watercraft.) Wax the hull with a non-abrasive wax
such as Yamalube Professional Polish. EJU44950
Lubrication
To keep moving parts sliding or rotating smoothly, lubricate them with water-resistant grease.
Recommended water-resistant grease: YAMALUBE MARINE GREASE
  94
]]></page><page Index="101" isMAC="true"><![CDATA[Care and storage
   Steering cable (jet thrust nozzle end), elec- tric trim rod (jet thrust nozzle end), and ball joint
             TIP:
Disconnect the electric trim rod from the ball joint before lubricating.
  Shift rod (reverse gate end) and ball joint
            TIP:
Disconnect the shift rod from the ball joint be-
fore lubricating.
EJU40263
Rustproofing
Spray metallic parts of the hull, deck, and en-
gine with a rust inhibitor such as Yamalube Silicone Protectant & Lubricant.
Have a Yamaha dealer rustproof the internal engine components.
95
]]></page><page Index="102" isMAC="true"><![CDATA[Maintenance
EJU33758
Maintenance
Periodic checks and lubrication will keep your watercraft in the safest and most effi- cient condition possible. Therefore, make sure to carry out the periodic maintenance. Safety is an obligation of the watercraft own- er. Proper maintenance must be carried out to keep the exhaust emission and sound lev- els within the regulated limits. The most im- portant points of watercraft inspection and lubrication are explained on the following pages.
See a Yamaha dealer for genuine Yamaha re- placement parts and optional accessories designed for your watercraft.
Remember, failures that are the result of the installation of parts or accessories which are not qualitatively equivalent to genuine Yamaha parts are not covered by the limited warranty.
Maintenance, replacement, or repair of the emission control devices and system may be performed by any marine SI engine repair establishment or individual. War- ranty repair, however, must be performed at an authorized Yamaha marine dealer- ship.
EWJ00312
Be sure to turn off the engine when you perform maintenance unless otherwise specified. If you are not familiar with ma- chine servicing, this work should be done by a Yamaha dealer or other qualified me- chanic.
A service manual is available for purchase through a Yamaha dealer for owners who have the mechanical skills, tools, and other equipment necessary to perform mainte-
nance not covered by this owner’s/operator’s
manual.
EJU42023
Removing and installing the engine
cover
The engine cover is removable. To remove the engine cover:
(1) Remove the seats. (See page 54 for seat
removal and installation procedures.)
(2) Remove the engine cover screws.
   1
  1 Engine cover screw
(3) Lift up the engine cover to remove it.
 1
     1 Engine cover
 96
]]></page><page Index="103" isMAC="true"><![CDATA[To install the engine cover:
(1) Place the engine cover in its original po-
sition, and then push it down.
Maintenance
     (2) Install the engine cover screws.
(3) Securely install the seats in their original
positions.
97
]]></page><page Index="104" isMAC="true"><![CDATA[Maintenance
EJU43101
Periodic maintenance chart
The periodic maintenance chart gives general guidelines for periodic maintenance. Have a Yamaha dealer perform the checks in the following chart. However, maintenance may need to be performed more frequently depending on your operating conditions. If you have any questions, consult a Yamaha dealer.
This “√” mark indicates items to be checked and serviced by a Yamaha dealer.
      Item
Operation
Initial
Thereafter every
Page
10 hours
50 hours or 12 months *1
100 hours or 12 months *1
200 hours or 24 months *1
Fuel line
Check fuel hoses and clamps
√
—
Fuel filler cap/Wa- ter separator
Check O-rings for cracks and deformation
√
—
Fuel tank
Check installation and straps
√
—
Water inlet strainer
Check for clogs and dam- age
√
—
Cooling water hos- es
Check for damage and leakage, and check clamps
√
—
Engine oil
Replace
√
√
100
Oil filter
Replace
√
100
Intermediate hous- ing
Lubricate
√
—
Spark plugs
Check
√
√
—
Battery
Check state of charge, terminals and bands
√
—
Battery leads
Check terminals
√
—
Steering master
Check operation and for looseness
√
√
—
Steering cable
Check exterior and con- nections, and lubricate
√
—
Electric trim rod
Check exterior and con- nections, and lubricate
√
—
Shift rod and re- verse gate
Check exterior and con- nections, and lubricate
√
—
Air filter element
Check for damage and dirt
√
—
Air intake hoses
Check for damage, and check clamps
√
—
Throttle body
Lubricate throttle valve
√
—
                        98
]]></page><page Index="105" isMAC="true"><![CDATA[Maintenance
      Item
Operation
Initial
Thereafter every
Page
10 hours
50 hours or 12 months *1
100 hours or 12 months *1
200 hours or 24 months *1
Exhaust system
Check for exhaust leak- age, and check hoses and clamps
√
—
Breather hose
Check breather hose and clamps
√
—
Impeller
Check for bends, dam- age, and foreign material
√
—
Jet thrust nozzle
Check movement, and lu- bricate
√
—
Jet vacuum bilge
Check hoses for clogs and damage, check clamps, and clean bilge strainer
√
—
Stern drain plugs
Check O-rings
√
—
Anode
Check for corrosion, and clean
√ *2
—
Valve clearance
Check and adjust
√ *2
—
Rubber coupling
Check for cracks, inden- tations, looseness, and noise
√
—
Engine mount
Check for damage and peeling
√
—
                *1: Whichever comes first.
*2: Check every 200 hours.
Perform the pre-operation checks and post-operation checks before performing periodic maintenance.
99
]]></page><page Index="106" isMAC="true"><![CDATA[Maintenance
EJU36943
Engine oil and oil filter
EWJ00341
Engine oil is extremely hot immediately af- ter the engine is turned off. Coming in con- tact with or getting any engine oil on your clothes could result in burns.
ECJ00992
Do not run the engine with too much or not enough oil in the engine, otherwise the en- gine could be damaged.
It is recommended to have a Yamaha dealer change the engine oil and the engine oil filter. However, if you choose to change the oil and filter on your own, consult a Yamaha dealer.
       100
]]></page><page Index="107" isMAC="true"><![CDATA[ EJU45432
Specifications Watercraft capacity:
Maximum people on board: 3 person
Maximum load capacity: 240 kg (530 lb)
Dimensions and weight:
Length:
3.58 m (140.9 in)
Width:
1.27 m (50.0 in)
Height:
1.23 m (48.4 in)
Dry weight:
371 kg (818 lb) (FX SVHO)
372 kg (820 lb) (FX CRUISER SVHO) 373 kg (822 lb) (FX LIMITED SVHO)
Performance:
Maximum fuel consumption:
80.7 L/h (21.3 US gal/h, 17.8 Imp.gal/h)
Cruising range at full throttle: 0.87 hour
Trolling speed: 1250 ±100 r/min
Engine:
Engine type:
Liquid cooled 4-stroke, DOHC
Number of cylinders: 4
Engine displacement: 1812 cm3
Bore × stroke:
86.0 × 78.0 mm (3.39 × 3.07 in)
Compression ratio: 8.5 : 1
Valve clearance-intake (cold): 0.14–0.23 mm (0.0055–0.0091 in)
Valve clearance-exhaust (cold): 0.36–0.45 mm (0.0142–0.0177 in)
Lubrication system: Wet sump
Cooling system: Water
Starting system: Electric
Ignition system: T.C.I.
Specifications
Spark plug (NGK): LFR7A
Spark plug gap:
0.8–0.9 mm (0.031–0.035 in)
Battery capacity: 12 V, 18 Ah
Battery type: YTX20L-BS
Charging system: Flywheel magneto
Drive unit:
Propulsion system: Jet pump
Jet pump type:
Axial flow, single stage
Impeller rotation: Counterclockwise
Jet thrust nozzle angle: 24+24 °
Jet thrust nozzle trim angle: -5, -3, 0, 3, 6 °
Fuel and oil:
Recommended fuel:
Premium unleaded gasoline
Minimum octane rating (PON): 91
Minimum octane rating (RON): 95
Recommended engine oil:
YAMALUBE 4W or 4-stroke motor oil
Recommended engine oil type SAE:
SAE 10W-30, 10W-40, 20W-40, 20W-50
Recommended engine oil grade API: API SG, SH, SJ, SL
Fuel tank total capacity:
70 L (18.5 US gal, 15.4 Imp.gal)
Engine oil quantity with oil filter replacement: 3.7 L (3.91 US qt, 3.26 Imp.qt)
Engine oil quantity without oil filter replacement: 3.5 L (3.70 US qt, 3.08 Imp.qt)
Engine oil total quantity:
5.3 L (5.60 US qt, 4.66 Imp.qt)
 101
]]></page><page Index="108" isMAC="true"><![CDATA[Trouble recovery
EJU34562
 Troubleshooting
If you have any trouble with your watercraft, use the troubleshooting chart to check for the
possible cause.
If you cannot find the cause, consult a Yamaha dealer.
EJU45280
Troubleshooting chart
Confirm the possible cause and remedy, and then refer to the applicable page.
    TROUBLE
POSSIBLE CAUSE
REMEDY
PAGE
Engine does not start (Starter motor does not turn over)
Yamaha Se- curity System
Lock mode selected
Select unlock mode
30
Engine shut- off switch
Clip not in place
Install clip
31
Fuse
Burned out
Replace fuse and check wiring
107
Battery
Run down
Recharge
92
Poor terminal con- nections
Tighten as required
92
Terminal corroded
Clean or replace
92
Starter motor
Faulty
Have serviced by Yamaha dealer
—
Engine does not start (Starter motor turns over)
Throttle lever
Squeezed
Release
31
Faulty
Have serviced by Yamaha dealer
—
RiDE lever
Squeezed
Release
31
Faulty
Have serviced by Yamaha dealer
—
Fuel
Fuel tank empty
Refill as soon as pos- sible
62
Stale or contaminat- ed
Have serviced by Yamaha dealer
—
Fuel tank
Water or dirt present
Have serviced by Yamaha dealer
—
Spark plug
Fouled or defective
Have serviced by Yamaha dealer
—
Fuel injec- tion system
Fuel pump faulty
Have serviced by Yamaha dealer
—
                    102
]]></page><page Index="109" isMAC="true"><![CDATA[Trouble recovery
     TROUBLE
POSSIBLE CAUSE
REMEDY
PAGE
Engine runs irregu- larly or stalls
Fuel
Fuel tank empty
Refill as soon as pos- sible
62
Stale or contaminat- ed
Have serviced by Yamaha dealer
—
Incorrect octane number
Use correct fuel
62
Fuel tank
Water or dirt present
Have serviced by Yamaha dealer
—
Spark plug
Fouled or defective
Have serviced by Yamaha dealer
—
Incorrect heat range
Have serviced by Yamaha dealer
—
Gap incorrect
Have serviced by Yamaha dealer
—
Electrical wir- ing
Loose connection
Have serviced by Yamaha dealer
—
Fuel injec- tion system
Faulty or clogged in- jectors
Have serviced by Yamaha dealer
—
Warning is dis- played
Fuel level warning
Fuel tank empty
Refill as soon as pos- sible
62
Oil pressure warning
Oil pressure dropped
Have serviced by Yamaha dealer
53
Engine over- heat warning
Jet intake clogged
Clean
105
Check en- gine warning
Faulty sensors
Have serviced by Yamaha dealer
52
                 103
]]></page><page Index="110" isMAC="true"><![CDATA[Trouble recovery
     TROUBLE
POSSIBLE CAUSE
REMEDY
PAGE
Watercraft slow or loses power
Watercraft operation mode
Drive control mode activated
Deactivate or adjust drive control mode
41
Cavitation
Jet intake clogged
Clean
105
Impeller damaged or worn
Have serviced by Yamaha dealer
105
Engine over- heat warning
Engine speed reduc- tion control activated
Clean jet intake and cool engine
52
Oil pressure warning
Engine speed reduc- tion control activated
Add oil
53
Spark plug
Fouled or defective
Have serviced by Yamaha dealer
—
Incorrect heat range
Have serviced by Yamaha dealer
—
Gap incorrect
Have serviced by Yamaha dealer
—
Electrical wir- ing
Loose connection
Have serviced by Yamaha dealer
—
Fuel
Stale or contaminat- ed
Have serviced by Yamaha dealer
—
Incorrect octane number
Use correct fuel
62
Air filter
Clogged
Have serviced by Yamaha dealer
—
Oil buildup
Have serviced by Yamaha dealer
—
Throttle lever
Faulty
Have serviced by Yamaha dealer
—
                  104
]]></page><page Index="111" isMAC="true"><![CDATA[ EJU34625
Emergency procedures
EJU44590
Cleaning the jet intake and impeller
EWJ00783
Before attempting to remove weeds or de- bris from the jet intake or impeller area, shut the engine off and remove the clip from the engine shut-off switch. Severe in- jury or death could result from coming in contact with the rotating parts of the jet pump.
If weeds or debris gets caught in the jet intake or impeller, cavitation can occur, causing jet thrust to decrease even though engine speed rises. If this condition is allowed to continue, the engine will overheat and may seize. NOTICE: If weeds or debris gets caught in the jet intake, do not operate the water- craft above trolling speed until they have been removed. [ECJ00654]
If there is any sign that the jet intake or impel- ler is clogged with weeds or debris, return to shore and check the intake and impeller. Al-
Trouble recovery
ways stop the engine before beaching the watercraft.
          (1) Place a suitable clean cloth or carpeting underneath the watercraft to protect it from abrasions and scratches. Turn the watercraft on its side as shown. NOTICE: When turning the watercraft on its side, support the bow so that the handlebars are not bent or dam- aged. [ECJ02690]
  (2) Remove any weeds or debris from around the jet intake, drive shaft, impel-
105
]]></page><page Index="112" isMAC="true"><![CDATA[ Trouble recovery
ler, jet pump housing, and jet thrust noz- zle.
If debris is difficult to remove, consult a
Yamaha dealer. EJU43472
Raising the reverse gate
If the RiDE system malfunctions and the re- verse gate remains in the lowered position, the watercraft will not be able to move for- ward.
After raising the reverse gate so that the wa- tercraft can move forward, immediately re- turn to shore and have a Yamaha dealer service the watercraft.
To raise the reverse gate:
(1) Stop the engine and remove the clip from
the engine shut-off switch.
(2) Enter the water and move to the rear of
the watercraft.
(3) Slide the shift rod joint toward the bow,
and then disconnect the shift rod joint from the ball joint.
(4)
Raise the reverse gate to the forward po- sition.
    1
2
       1
2
    1 Shift rod joint
2 Ball joint
1 Reverse gate
2 Forward position
TIP:
  While the shift rod is disconnected, the re- verse gate will not move to the neutral po- sition or reverse position even if the RiDE lever is squeezed.
  If the RiDE lever is squeezed while the shift
rod is disconnected, the watercraft will
move forward. EJU34642
Jumping the battery
If the watercraft battery has run down, the en-
gine can be started using a 12-volt booster
battery and jumper cables. EJU34664
Connecting the jumper cables EWJ01251
To avoid battery explosion and serious damage to the electrical system:
  Do not reverse the polarity of the jumper
cables when connecting to the batter-
ies.
  Do not connect the negative (–) jumper
cable to the negative (–) terminal of the
watercraft battery.
  Do not touch the positive (+) jumper ca-
ble to the negative (–) jumper cable.
 106
]]></page><page Index="113" isMAC="true"><![CDATA[1 Negative (–) jumper cable
2 Booster battery
3 Positive (+) jumper cable
4 Engine hanger
(4) Start the engine, and then disconnect the jumper cables by reversing the steps above. (See page 31 for information on starting the engine.)
1 Good fuse 2 Blown fuse
To replace a fuse:
(1) Remove the seats and removable water-
tight storage compartment. (See page 54 for seat removal and installation proce- dures and page 60 for information on the removable watertight storage compart- ment.)
(2) While pushing the projection on each lock, slide the locks outward.
1 Good fuse 2 Blown fuse
Trouble recovery
 (1) Connect the positive (+) jumper cable to the positive (+) battery terminals of both batteries.
(2) Connect one end of the negative (–) jumper cable to the negative (–) battery terminal of the booster battery.
(3) Connect the other end of the negative (–) jumper cable to an engine hanger.
EJU43482
Replacing the fuses
If a fuse is blown, replace it with the proper fuse.
 1
  2
      1
2
3
     4
        1
        2
       107
]]></page><page Index="114" isMAC="true"><![CDATA[Trouble recovery
(3) Remove the electrical box cover.
Install the spare fuse, and then tighten the screws.
       1
3
2
2 3
          1234567
10 5
8 9
8
 1 Electrical box cover 2 Lock
3 Projection
(4) While pushing both sides of the fuse box cover inward, pull the cover toward the bow and remove it.
1 Electronic throttle valve fuse 2 Fuel pump fuse
3 Main relay drive fuse
4 Main fuse
5 Spare fuse 6 Fuse puller 7 Battery fuse 8 Screw
9 SCU fuse (BCU fuse) 10 Unused fuse
(6) When replacing a fuse other than the SCU fuse, remove the fuse using the fuse puller. Install a spare fuse of the proper amperage. WARNING! Do not use fuses of a different amperage than recommended. Substitution with a fuse that has an improper rating can cause extensive electrical system damage and possible fire. [EWJ00803]
      1
          1 Fuse box cover
(5) When replacing the SCU fuse, remove
the screws, and then remove the fuse.
108
]]></page><page Index="115" isMAC="true"><![CDATA[(7) Securely install the fuse box cover in its original position.
(8) Securely install the electrical box cover in its original position.
(9) Slide the locks to their original positions to securely lock the electrical box cover in place.
(10) Securely install the removable watertight storage compartment and seats in their original positions.
If the fuse immediately blows again, the elec-
trical system may be defective. If this occurs,
have a Yamaha dealer service the watercraft. EJU34716
Towing the watercraft
EWJ00812
  The operator of the towing boat must keep speed to a minimum and avoid traffic or obstacles which could be a hazard to the operator on the water- craft.
  The towline should be long enough so that the watercraft will not collide with the towing boat when slowing down.
If the watercraft becomes inoperative in the water, it can be towed to shore.
1 Bow eye
(2) Sit astride the seat and hold on to the handlebars in order to balance the water- craft. NOTICE: The bow must be kept up out of the water during towing, oth- erwise water could flood the engine compartment or water could flow back into the engine, causing severe engine damage. [ECJ01331]
Tow the watercraft at 8 km/h (5 mph) or less.
NOTICE: Tow the watercraft at 8 km/h (5 mph) or less, otherwise water could flood the engine compartment or water could flow back into the engine, causing severe
engine damage. [ECJ01322]
EJU36156
Submerged watercraft
If the watercraft is submerged or flooded with
water, drain the bilge water from the engine compartment. Then, have a Yamaha dealer service the watercraft as soon as possible.
If the watercraft was submerged:
(1) Remove the watercraft from the water and drain the water from the storage compartments. (See page 57 for infor-
Trouble recovery
To tow the watercraft:
Use a towline that is three times the com- bined length of the towing boat and the wa- tercraft.
(1) Securely attach the towline to the bow
eye of the watercraft being towed.
    Fuse amperage:
Electronic throttle valve fuse:
10 A
Fuel pump fuse:
10 A
Main relay drive fuse:
10 A Main fuse: 20 A
Battery fuse: 30 A
SCU fuse: 50 A
           1
     109
]]></page><page Index="116" isMAC="true"><![CDATA[Trouble recovery
mation on draining the storage compart-
ments.)
(2) Drain the bilge water from the engine
compartment. (See page 66 for informa-
tion on draining the bilge water.)
(3) Have the watercraft serviced by a Yamaha dealer as soon as possible. NOTICE: Be sure to have a Yamaha dealer inspect the watercraft. Other- wise, serious engine damage could
result. [ECJ00792]
 110
]]></page><page Index="117" isMAC="true"><![CDATA[ EJU34785
Consumer information Limited warranty
 YAMAHA MOTOR CORPORATION, U.S.A. WAVERUNNER® WATERCRAFT LIMITED WARRANTY
Yamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha WaveRunner watercraft purchased from an authorized Yamaha WaveRunner Watercraft Dealer in the United States (excluding its territories) will be free from defects in material and workmanship for the period of time stated herein, subject to certain stated limitations.
PERIOD OF WARRANTY. Any new Yamaha WaveRunner watercraft purchased for pleasure use will be warranted for a period of one (1) year from the date of purchase, subject to exclusions noted herein. Any Yamaha WaveRunner watercraft purchased and utilized for commercial applications will be warranted for a period of ninety (90) days from the date of purchase, subject to exclusions noted herein. The battery will be warranted against defects in material or workmanship for thirty (30) days from the date of vehicle purchase for either pleasure or commercial use. Replacement parts used in warranty repairs will be warranted for the balance of the applicable warranty period.
OBTAINING REPAIRS UNDER WARRANTY. During the period of warranty, any authorized Yamaha WaveRunner Watercraft Dealer will, free of charge, repair or replace, at Yamaha’s option, any part adjudged defective by Yamaha due to faulty workmanship or material from the factory. All parts replaced under warranty will become the property of Yamaha Motor Corporation, U.S.A.
THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to:
1. Operate, maintain, and store the WaveRunner watercraft as specified in the appropriate Owner’s/Operator’s Manual, and
2. Give notice to an authorized Yamaha WaveRunner watercraft dealer of any and all apparent defects within ten (10) days after
discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business.
GENERAL EXCLUSIONS from this warranty shall include any failures caused by:
a. Racing or competition use, modification of original parts, abnormal strain.
b. Lack of proper maintenance and off-season storage as described in the Owner’s/Operator’s Manual.
c. Installation of parts or accessories that are not equivalent in design and quality to genuine Yamaha parts.
d. Use of lubricants, oils, and fuels that are not suitable for WaveRunner watercraft use.
e. Damage as a result of accidents, collisions, contact with foreign materials, or submersion.
f. Growth of marine organism on motor or hull surfaces.
g. Normal deterioration.
h. Gel coat stress cracks
i. Damage due to improper transportation.
SPECIFIC PARTS EXCLUDED FROM WARRANTY. Parts replaced due to normal wear or routine maintenance such as oil, spark plugs, fuel filters, impeller and liner, and anodes are not covered by warranty. Charges for transporting the WaveRunner watercraft to and from an authorized Yamaha WaveRunner Watercraft Dealer are excluded from warranty coverage.
EMISSION CONTROL WARRANTY.
Yamaha warrants to the ultimate purchaser and any subsequent owner, that the exhaust emission control components on this engine are designed, built and equipped so as to conform at the time of sale with applicable regulations under section 213 of the Clean Air Act and that this engine is free from defects in materials and workmanship which cause said engine to fail to conform with applicable regulations for 30 months from the date of purchase or 175 hours of operation, whichever comes first. For evaporative emission components, for a failure that will increase evaporative emissions, the warranty coverage is 2 years from the date of purchase. Some states may have different emission control warranty provisions. As these vary from state to state, consult your Yamaha dealer or contact Yamaha Customer Relations at 1-800-962-7926 for more information.
WARRANTY TRANSFER: To transfer the warranty from the original purchaser to any subsequent purchaser(s), it is imperative that the WaveRunner watercraft be inspected and registered for warranty by an authorized Yamaha WaveRunner watercraft dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer of ownership to the subsequent purchaser. A reasonable dealer-imposed fee may be charged for this inspection.
YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIMITS STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPORATION, U.S.A. AND EXCLUDED FROM THIS WARRANTY.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS OF USE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
111
]]></page><page Index="118" isMAC="true"><![CDATA[Consumer information
  THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
YAMAHA MOTOR CORPORATION, U.S.A. Post Office Box 6555 Cypress, California 90630
WARRANTY QUESTIONS AND ANSWERS
Q. What costs are my responsibility during the warranty period?
A. The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision dam-
ages.
Q. What are some examples of “abnormal” strain, neglect, or abuse?
A. These terms are general and overlap each other in areas. Specific examples include:
Running the watercraft out of oil, operating the machine with a broken or damaged part which causes another part to fail, and so on. If you have any specific questions on operation or maintenance, please contact your Yamaha dealer for advice.
Q. Does the warranty cover incidental costs such as transportation due to a failure? A. No. The warranty is limited to repair of the watercraft itself.
Q. May I perform any or all of the recommended maintenance shown in the Owner’s/Operator’s Manual instead of having the dealer do them?
A. Yes, if you are a qualified mechanic and follow the procedures specified in the Owner’s/Operator’s and Service Manual. We do rec- ommend, however, that items requiring special or equipment be done by a Yamaha dealer.
Q. Will the warranty be void or cancelled if I do not operate or maintain my new watercraft exactly as specified in the Owner’s/Opera- tor’s Manual?
A. No. The warranty on a new watercraft cannot be “voided” or “cancelled”. However, if a particular failure is caused by operation or maintenance other than as shown in the Owner’s/Operator’s Manual, that failure may not be covered under warranty.
Q. What responsibility does my dealer have under this warranty? A. Each Yamaha dealer is expected to:
1. Completely set up each new watercraft before sale.
2. Explain the operation, maintenance, and warranty requirements to your satisfaction at the time of sale, and upon your request at
any later date. In addition, each Yamaha dealer is held responsible for his setup, service and warranty repair work.
Q. Is the warranty transferable to second owners?
A. Yes. The remainder of the existing warranty can be transferred upon request. The unit has to be inspected and re-registered by an
authorized Yamaha dealer for the policy to remain effective.
CUSTOMER SERVICE
If your watercraft requires warranty service, you must take it to any authorized Yamaha dealer within the continental United States. Be sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises regard- ing warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, this person is in the best position to help you. If you are still not satisfied and require additional assistance, please write:
YAMAHA MOTOR CORPORATION U.S.A. CUSTOMER RELATIONS DEPARTMENT P.O. Box 6555
Cypress, California 90630
CHANGE OF ADDRESS
The federal government requires each manufacturer to maintain a complete, up-to-date list of all first purchasers against the possibility of a safety-related defect and recall. This list is complied from the purchase registrations sent to Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.
If you should move after you have purchased your new watercraft, please advise us of your new address by sending a postcard listing your Yamaha model name, engine number, dealer number [or dealer’s name] as it is shown on your warranty card, your name and new mailing address.
Mail to:
YAMAHA MOTOR CORPORATION, U.S.A. 1270 Chastain Road Kennesaw, Georgia 30144 Attention: Warranty Department
This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.
112
]]></page><page Index="119" isMAC="true"><![CDATA[ EJU34803
Consumer information YAMAHA EXTENDED SERVICE (Y.E.S.)
 Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.).
• Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.
• Y.E.S. is flexible. You choose the plan that is right for you: 12 months, 24 months, 36 months, or (on four-stroke models) 48 months beyond your warranty period.
• Y.E.S. is designed and administered by the same Yamaha people who handle your warranty— and it shows in the comprehensive coverage benefits. There are no mileage limitations. Cover- age is not limited to “moving parts” or the “drive train” like many other plans. And Y.E.S. covers manufacturing defects just like the warranty. See the sample contract at your Yamaha dealer to see how comforting uninterrupted factory-backed protection can be.
• You do not have to pay anything for covered repairs. There is no deductible to pay, and repairs are not “pro-rated.” You do not have any “out-of-pocket” expenses for covered repairs.
• In addition, Travel and Recreation Interruption Protection (TRIP) is included at no extra cost. TRIP gives you up to $250 reimbursement per occurrence for any reasonable expenses you incur because your Yamaha needs covered service: replacement vehicle rental, emergency towing, phone calls, even food and lodging when you are away from home. This superb cover- age goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as covered repairs during your entire Y.E.S. plan period.
• Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.
• Y.E.S. coverage is transferable to a new owner if you sell or trade-in. That can make your Yamaha much more valuable!
This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service.
We urge you to act now. You will get the excellent benefits of TRIP coverage right away, and you will rest easy knowing you will have strong factory-backed protection even after your Yamaha Limited Warranty expires.
A special note:
If visiting your dealer is not convenient, contact Yamaha with your Primary ID number (your Owner’s Manual shows you where to find this number). We will be happy to help you get the Y.E.S. coverage you need.
Yamaha Service Marketing P.O. Box 6555
Cypress, CA 90630 1-(866)-YES-EXTD (1-866-937-3983)
 113
]]></page><page Index="120" isMAC="true"><![CDATA[Index
A
Adjustable tilt steering system ................. 33 Adjustable tilt steering system checks .... 74 After removing the watercraft from the
water ..................................................... 90 Approval label of emission control
certificate ................................................ 2
B
Battery care.............................................. 92 Battery checks ......................................... 72 Battery, jumping..................................... 106 Beaching and docking the watercraft ...... 89 Beverage holder ....................................... 60 Bilge water check..................................... 72 Bilge water, draining ................................ 66 Bilge water, draining on land ................... 66 Bilge water, draining on water ................. 66 Boarding alone ......................................... 85 Boarding and starting off from a dock ..... 88 Boarding the watercraft ........................... 85 Boarding with passenger(s) ..................... 86 Bow eye ................................................... 56 Bow storage compartment ...................... 57 C
Capsized watercraft ................................. 88 Cleaning ................................................... 94 Cleaning the watercraft ............................ 92 Cleat ......................................................... 56 Cooling water pilot outlet check .............. 77 Cooling water pilot outlets ....................... 34 Cruise assist............................................. 43 Cruising limitations................................... 11 D
Drive control mode................................... 41 Drive control mode screen....................... 49 E
Electric trim system.................................. 37 Electric trim system check ....................... 75 Emergency procedures.......................... 105 Emission control information ..................... 2 Engine break-in ........................................ 68 Engine compartment check ..................... 71 Engine cover, removing and installing ..... 96 Engine idling speed check ....................... 78 Engine lock screen................................... 51
Engine oil.................................................. 64 Engine oil and oil filter ............................ 100 Engine oil level check............................... 72 Engine oil requirements ........................... 64 Engine serial number ................................. 2 Engine shut-off cord (lanyard) check ....... 74 Engine shut-off switch ............................. 31 Engine stop switch ................................... 31 Engine unit check..................................... 72 Enjoy your watercraft responsibly............ 24 Equipment ................................................ 54 F
Fire extinguisher check ............................ 76 Fire extinguisher holder and cover........... 61 Fire extinguisher holder, cover, and
band checks ......................................... 75 Flushing the cooling water passages....... 91 Fuel .......................................................... 62 Fuel level check........................................ 71 Fuel requirements .................................... 62 Fuel system checks ................................. 71 Fuses, replacing ..................................... 107 G
Getting to know your watercraft .............. 79 Glossary, watercraft ................................. 25 Glove compartment ................................. 58 H
Handgrip .................................................. 55 Hazard information................................... 15 Home screen ............................................ 47 Hood check .............................................. 77 Hull and deck check ................................ 76 Hull Identification Number (HIN)................. 2 I
Identification numbers ............................... 1 Information screen ................................... 48 J
Jet intake and impeller, cleaning............ 105 Jet intake checks ..................................... 76 Jet thrust nozzle and reverse gate
check .................................................... 76 Jumper cables, connecting .................... 106 L
Labels, important ....................................... 5 Labels, other .............................................. 8
 114
]]></page><page Index="121" isMAC="true"><![CDATA[ Labels, warning .......................................... 6 Launching the watercraft ......................... 80 Learning to operate your watercraft ........ 79 Leaving the watercraft ............................. 81 Limitations on who may operate the
watercraft.............................................. 10 Limited warranty .................................... 111 Long-term storage ................................... 94 Lubrication ............................................... 94 M
Main components, location of ................. 26 Maintenance ............................................ 96 Manufactured date label ............................ 3 Multifunction information center .............. 45 Multifunction information center check ... 77 N
No-wake mode ........................................ 40
O
Operating in weeded areas ...................... 89 Operating the watercraft .......................... 81 Operating the watercraft in reverse or
neutral ................................................... 84 Operating your watercraft ........................ 79 Operation buttons .................................... 46 Operation requirements ........................... 12 Optional part mounting bracket ............... 61 P
Periodic maintenance chart ..................... 98 Post-launch checks ................................. 77 Post-operation care ................................. 91 Pre-launch checks ................................... 71 Pre-operation check points ..................... 71 Pre-operation checklist ............................ 69 Primary Identification (PRI-ID) number ...... 1 Pull-up cleats (FX CRUISER SVHO / FX
LIMITED SVHO) .................................... 57
R
Raising the reverse gate ........................ 106 Reboarding grip ....................................... 55 Reboarding step ...................................... 55 Recommended equipment ...................... 15 Removable watertight storage
compartment ........................................ 60 Reverse assist .......................................... 39 RiDE lever................................................. 32
Index
RiDE lever checks .................................... 74 Riding position ......................................... 80 Rules of the Road .................................... 19 Rustproofing ............................................ 95 S
Safety equipment check .......................... 76 Seats ........................................................ 54 Setting menu screen ................................ 49 Shift system ............................................. 35 Shift system check ................................... 77 Star labels .................................................. 3 Start switch .............................................. 31 Starting off ............................................... 87 Starting off from a trailer .......................... 88 Starting the engine on water .................... 80 Status area ............................................... 47 Steering system ....................................... 32 Steering system checks ........................... 73 Stern drain plug checks ........................... 76 Stern eyes ................................................ 56 Stern storage compartment ..................... 59 Stopping the engine ................................. 81 Stopping the watercraft ........................... 83 Storage compartment checks.................. 75 Storage compartments ............................ 57 Submerged watercraft ........................... 109 Switch checks .......................................... 74 T
T.D.E. (thrust directional enhancer).......... 39 Throttle lever ............................................ 32 Throttle lever checks ................................ 74 To get more boating safety information ... 23 Touch screen ........................................... 46 Towing the watercraft ............................ 109 Transporting on a trailer ........................... 67 Troubleshooting ..................................... 102 Troubleshooting chart ............................ 102 Turning the watercraft .............................. 82 W
Wakeboarding and water-skiing .............. 17 Warning function ...................................... 51 Water separator ....................................... 34 Water separator check ............................. 72 Watercraft characteristics ........................ 16 Watercraft control functions..................... 30
115
]]></page><page Index="122" isMAC="true"><![CDATA[Index
Watercraft operation functions ................ 35 Watercraft operation modes .................... 39 Y
YAMAHA EXTENDED SERVICE
(Y.E.S.) ................................................ 113 Yamaha Security System.........................30 Yamaha Security System check .............. 74 Yamaha Security System setting ............. 30
 116
]]></page><page Index="123" isMAC="true"><![CDATA[EJU42011
 For your best ownership experience, think Genuine Yamaha!
Genuine Yamaha Parts – Genuine Yamaha replacement parts are the exact same parts as the ones originally equipped on your vehicle, providing you with the performance and durability you have come to expect. Why settle for aftermarket parts that may not provide full confidence and satisfaction?
Genuine Yamaha Accessories – Yamaha only offers accessories that meet our high standards for quality and performance. Buy with confidence, knowing your Genuine Yamaha Accessories will fit right and perform right – right out of the box.
Yamalube – Take care of your Yamaha with legendary Yamalube oils, lubricants, and care products. They’re formulated and approved by the toughest judges we know: the Yamaha engineering teams that know your Yamaha from the inside out.
Genuine Yamaha Service Manuals – Get the same factory manual for your vehicle that the technicians at your authorized Yamaha dealer use. Service manuals are available through your Yamaha dealer or you can order them directly through yamahapubs.com.
Genuine Yamaha products are available only from your Yamaha dealer. Find out more at yamaha-motor.com
]]></page><page Index="124" isMAC="true"><![CDATA[ Printed in U.S.A.
June 2020–1.5 × 1 CR
]]></page></pages></Search>